Safety Instructions • Rough handling of product may cause physical damage or malfunction. • Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock. • To avoid electric shock, never touch the inside of the monitor. Only a qualified should open the monitor’s case.
Buttons Power Switch turns power on/off. Menu/Exit displays the OSD menu or exit from current menu. Input selects input signal. Function 1~3 Activates/deactivates function 1~3. Audio Out enables user monitor the audio by headphone. is used to update the firmware. Serial is used to update the firmware or to calibrate color.
OSD Menu * The menu may disappear on no signal or instable signal input. * Menu setting is saved for each input mode. So the user should make selection on an appropriate input mode. * If there's no picture change for long, the picture might be left unchanged for some time.
Page 7
SDI Switching Enables smooth switching on the picture if input picture source is changed quickly from such input device as routing switcher. SDI 3G Mode Set this mode if the input is 3G HD SDI. SDI 3G mode support SMPTE standards listed below: ▶...
Page 8
Especially for 3G Level B signals, the format should be set manually. Also, be aware that the format information might be lost on power down. HDMI UV Swap Sometimes UV signal might be opposite such input as PC RGB or such resolution as PC’s.
DISPLAY 1 Aspect Sets the aspect ratio of the screen. 16:9, 4:3, Native(Original) are selectable. Anarmorphic Set this mode to resize the screen to 3.56:1, 2.74:1, 2.59:1, 2.55:1, 2.40:1, 2.39:1, 2.35:1, 1.85:1, 1.75:1, 1.66:1, or 1.37:1. Waveform Display Select waveform display mode. Choose Normal to analyze whole screen, choose Line Select to analyze a specific line of the screen.
Page 10
WFM & Vector Blend Set transparency of Waveform and Vectorscope window between 0~6. YCbCr YCbCr is a digital color reproduction standard. Y is for luminance, Cb is for blue strength, Cr is for red strength.
DISPLAY 2 Timecode Display Set this mode on to display timecode from SDI signal. Select the appropriate timecode that you wish to display among LTC (Longitudinal Time Code), VITC (Vertical Interval Time Code), DVITC (Digital Vertical Interval Time Code). Timecode Position Set Top or Bottom position for timecode.
Page 12
in front. Focus Assist Box Sets focus assist box size for user-interested region among small/medium/large, instead of setting full screen focus assist. Focus Assist Position Adjusts focus assist box position among 9 positions from the center, top-left, top-middle, top-right, left, center, right, bottom-left, bottom-middle, bottom-right. Focus Assist Color Set brush color of focus assist mode among Blue, Green, and Red.
COLOR Dithering Set this mode on to display gradient more smoothly. Auto Color Temperature Set this mode on to adjust color temperature by temperature change. Its output might incorrect on some harsh environment. Color Temperature VAR, 3200K, 5400K, 6500K, 9300K color temperatures are preset and selectable by user. On User mode, user can adjust RGB gain and bias.
MARKER Marker Ratio Select one of preset markers or user marker. To display marker, press Marker button in front of the monitor. Center Marker Set preference to display center marker or not. Safety Area 16:9 Adjust size of the safety area when marker displayed on 16:9 screen. Safety Area 4:3 Adjust size of the safety area when marker displayed on 4:3 screen.
OSD 1 OSD Display Time Set OSD menu display time. Choose 0 for infinite. OSD Blend Set transparency of the menu between 0 to 5. OSD(Menu) Position Set menu position among Left Top, Right Top, Left Bottom, Right Bottom and Center. Internal Pattern To test monitor display without signal, turn this mode on.
OSD 2 H/V Level Meters Displays the horizontal and vertical angle on screen. H/V Level Position Sets the position of level meters. H/V Size Sets large or small level meter size. H/V Sensitivity Sets the sensitivity of level change. Flip/Level Reset Resets the flip and angle meters.
Page 17
Tally Operating Level Sets tally input level. Low (Open) : below 0.6V, Green + Black (GND) High : over 2.5V, Red(5V) + Green Caution : Do NOT use Red(5V) + Black(GND). It can cause electric shock on the monitor. Tally Color Sets tally color among Red, Green, Amber.
AUDIO Audio Level Meter Display Turns on/off audio level meters. Level Meter SDI Channel Set the audio channels to display. Level Meter Type Select one of two types: pair or group. Level Meter Direction Select one of two orientations : Horizontal or Vertical. Level Meter Size Select the size of the meters : Small or Large.
Page 19
Embedded Audio Left Select audio channel for left (Ch 1 ~ 15) Embedded Audio Right Select audio channel for right (Ch 2 ~ 16) Audio Source Select audio source among Auto / SDI / Line In / HDMI...
SYSTEM Function 1,2,3 Assigns a function to each function button. Backlight Set the backlight intensity from 0 to 40. An LCD panel requires more than 30 minutes to be settled to a new backlight value. Font Button Lock Locks front buttons not to work. Press and hold Menu button for 3 seconds to exit from this mode.
Program Update Port (PGM) This mini USB port is used for updating firmware. It is recommended to get help from an expert. Before connecting a cable, the monitor DC power should be disconnected to prevent malfunction of the monitor.
BON Logo nor "No Signal" (Call for Service if the Symptom appeared more than 3 times) Display, but Buttons are Working There's a delay in BON Logo Display It is normal and No Reaction Required. on Startup Remove Input Cable and Check if "No Signal" appears on Screen.
Page 23
Strange Color on BON Logo on Reconnect the Power and Restart the Monitor. Startup (Call for Service if the Symptom appeared more than 3 times) Make Monitor "Factory Default" and Try again. Select Test Pattern(Internal Pattern) in the menu and See if R,G,B Color is Correct.
Warranty Information Free Service If the product needs to be repaired in 12 months from the purchase. Exceptions • damage caused by accident, abuse, misuse, water, flood, fire, or other acts of nature or external causes • damage caused by service performed by anyone who is not an authorized service provider •...
Page 25
Corporate Headquarters Tresebelle-Sky 2F, 1479 Gayang-2, Gangseo-gu, Seoul, South Korea Research / Service Center Vision Tower 7F, 1481 Gayang-2, Gangseo-gu, Seoul, South Korea Telephone +82 2 2659 0333 +82 2 2659 8133 www.bon-electronics.com Email sales@bon-electronics.com...
Need help?
Do you have a question about the FM-055F and is the answer not in the manual?
Questions and answers