LG RZ-37LZ55 Owner's Manual page 51

08. Brightness (Command:h)
G To adjust screen brightness.
You can also adjust brightness in the Picture menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 (transmit by Hexadecimal code)
•
Refer to 'Real data mapping 1'. See page 50.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
9. Colour (Command:i)
G To adjust the screen colour.
You can also adjust colour in the Picture menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 (transmit by Hexadecimal code)
•
Refer to 'Real data mapping 1'. See page 50.
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
10. Tint (Command:j)
G To adjust the screen tint.(NTSC M input only)
You can also adjust tint in the Picture menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 (transmit by Hexadecimal code)
•
Refer to 'Real data mapping 1'. See page 50.
Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command:k)
G To adjust the screen sharpness.
You can also adjust sharpness in the Picture menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 (transmit by Hexadecimal code)
•
Refer to 'Real data mapping 1'. See page 50.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command:l)
G To select OSD (On Screen Display) mute on/off.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD mute on 1: OSD mute off
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
13. Key Lock (Command:m)
G To lock the side panel controls on the TV.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off 1: Lock on
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
•
If you're not using the side panel controls on the TV, use
this mode. When main power is on/off, remote control
lock is released.
14. Balance (Command:t)
G To adjust balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 (transmit by Hexadecimal code)
•
Refer to 'Real data mapping 1'. See page 50.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
15. Programme Select (Command:m a) (Main TV Input)
G Tune channel to following Physical/major/minor number.
Transmission
[m][a][ ][Set ID][ ][Data0][Cr]
Data0: Programme Number
Min : 0 ~ Max : 63(transmit by Hexadecimal code)
•
Refer to 'Real data mapping 1'. See page 50.
Acknowledgement
[a][ ][Set ID][ ][OK][Data0][x]
[a][ ][Set ID][ ][NG][Data0][x]
16. Key (Command:m c)
G To send IR remote key code.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data: Key code (Refer to P.53)
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
51