LCD TV SERVICE MANUAL CHASSIS : ML-041B MODEL: RZ-15LA66 (RZ-15LA66 Rev A) ) ID LABEL Model No. CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. *Same looking with new chassis *Issue Date; 2004. 06...
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range This specification is applied to ML-041B chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ±...
Page 7
4. Feature and Function Item Specification Remark Teletext Top(option) TOP, FLOF,LIST 10 page REMOCON NEC Code PAL/ NTSC AV Input Rear(option, NT), S-Vedio Input Rear Component input Rear (option, NT) PERI TV Connector Full SCART : 1 Rear (option,EU) RGB(VGA)Input D-sub 15 pin H/p input PC Sound input...
Page 9
Item Specification Remark Power Supply H/V Sync Video Power Consumption LED Color Normal On/On Active GREEN Stand By Off/On Suspend Mode On/Off DPM Off Mode Off/Off Cut-off Switch off PBP SWAP ON/OFF ITEM Spectification Remark D-SUB Pin Configuraion 1: RED 2: Green 3: Blue: 4: ID2(GND)
Page 10
6-3. Power Item Unit Remark Video Input Level 0.85 1.15 EN-50049 Audio Input Level NTSC:0.4Vrms(Typ) Audio Input Frequency Response Audio Input S/N Audio Input Distortion Audio Input Dynamic Range Video Output Level 0.85 1.15 Video Output Frequency Response Video Output S/N Audio Output Level Audio Output Frequency Response Audio Output S/N...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Total Period Video Active Time Front Porch Sync Duration Back Porch Sync Mode Resolution Frequency Clock Sort Polarity 31.468 25.175 640x350 –...
ADJUSTMENT INSTRUCTION 1. Application Object 2.3 EDID (The Extended Display Identification Data) setting This instruction is for the application to the LCD TV. Connect the 15 Pin D-Sub Cable to D-Sub Jack. 2. Adjustment Set the input mode of Set to PC. Connect the DDC automation equipment to write 2.1 Adjustment overview DDC data.
Page 13
*Option(PAL) ITEM CONDITION REMARK ITEM CONDITION REMARK Option 1 Option 3 Side AV 0: Side AV Off Language 0: Eng Only 1: Side AV On 1: EU5 SCART 0: SCART Off 2: 12 nations(Europe) 1: SCART On 3: Eng + Chines 0: PC Off 4: Eng + France Arab 1: PC On...
Page 14
EDID ADJUSTMENT Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
SVC REMOCON To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily.
TROUBLESHOOTING No power :[A]Process (LED indicator off) Check short of main B/D Check 15V or 5V or Change Lips Fail of Lips Pass Check Output of Change Q1100 Fail Q1100 Pass Check Output of Change IC1107, IC1104 IC1107, IC104 Fail Pass Change LED Assy Check LED Assy...
Page 17
No Raster :[B]Process Check LED Status Repeat A PROCESS on display unit Fail Check L900,L901 Change L900,L901, L902,L903 L902,L903 Fail Pass Check the input/ Change IC901 Output of IC901 Fail Pass Change inverter Check inverter connector or inverter Connector or inverter Fail Pass Change panel link...
Page 18
No Raster on Component signal Repeat [A] Process Pass Check the signal of Check JA1200 or L1200, L1202, L1203 RCA CABLE Fail Pass Re-soldering or Check the input/ Change the defect part, Fail output of IC1 Check X11 Re-soldering or Check the input/output Change the defect part Fail...
Page 19
No Raster on AV Signal No Raster on TV(RF) signal (Video, S-Video) Check 5V, 33V of TU1000 Repeat Check the output of Re-soldering or [A] Process TU1000 Fail Fail Change the defect part Pass Check the signal of Change L1209, L1210, L1209, L1210, L1212 L1212 Fail...
Page 20
No Sound Check the Change source input input source Fail Pass Re-soldering or Check the input/output Change the defect part of IC1 Fail Check X11 Pass Re-soldering or Check the input/output Change the defect part of IC100,IC101 Fail Pass Check the speaker Change speaker Fail Pass...
Page 22
BLOCK DIAGRAM DESCRIPTION 1. Video Controller Unit & Display Data Conversion Unit The video controller unit receives the video signals inputted through the tuner, AV port (AV1, AV2, S-Video, component), and converts them into an analog RGB signal through the microcomputer (VCTI) combined with the video decoder that integrates various functions in one chip.
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)