THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
•
: Internal component.
f
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
Parts on the pattern face side seen
(Conductor Side)
from the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(Component Side)
the parts face are indicated.
Caution:
Pattern face side:
Parts on the pattern face side seen
(SIDE B)
from the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(SIDE A)
the parts face are indicated.
• MAIN board is multi-layer printed board. However, the
patterns of intermediate layers have not been included in
diagrams.
• Indication of transistor.
C
Q
These are omitted.
B
E
Note 1: When the complete MAIN board is replaced, refer
to "NOTE OF REPLACING THE IC3001 ON THE
MAIN BOARD AND THE COMPLETE MAIN
BOARD" and "NOTES ON THE WIRELESS CON-
NECTION (LINK) AFTER REPAIRS ARE COM-
PLETE" on page 5.
Note 2: When the complete POWER board is replaced, refer
to "BOND FIXATION OF ELECTRIC PARTS" on
page 6.
HT-CT380/CT381
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
•
: Internal component.
f
• 2 : Nonfl ammable resistor.
• 5 : Fusible resistor.
• C : Panel designation.
Note:
Note:
The components identi-
Les composants identifi és
fi ed by mark 0 or dotted
par une marque 0 sont
line with mark 0 are criti-
critiques pour la sécurité.
cal for safety.
Ne les remplacer que par
Replace only with part
une pièce portant le nu-
number specifi ed.
méro spécifi é.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : POWER ON
• Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
: AUDIO (ANALOG)
F
: AUDIO (DIGITAL)
J
E
: VIDEO
: Bluetooth
N
Note 1: When the complete MAIN board is replaced, refer
to "NOTE OF REPLACING THE IC3001 ON THE
MAIN BOARD AND THE COMPLETE MAIN
BOARD" and "NOTES ON THE WIRELESS CON-
NECTION (LINK) AFTER REPAIRS ARE COM-
PLETE" on page 5.
Note 2: When the complete POWER board is replaced, refer
to "BOND FIXATION OF ELECTRIC PARTS" on
page 6.
• Waveforms
– MAIN Board –
IC3109 ud (XTALOUT)
1
3.8 Vp-p
37.2 ns
1 V/DIV, 20 ns/DIV
IC3109 oa (MCLK)
2
4.6 Vp-p
59 ns
1 V/DIV, 50 ns/DIV
3
IC2005 qk (LRCK)
4.1 Vp-p
20.8 s
1 V/DIV, 10 s/DIV
4
IC2005 ql (BCK)
4.5 Vp-p
326 ns
1 V/DIV, 200 ns/DIV
IC2005 w; (SCKO)
5
3.7 Vp-p
40.2 ns
1 V/DIV, 20 ns/DIV
IC2005 r; (XTO)
6
2.8 Vp-p
40.2 ns
1 V/DIV, 20 ns/DIV
35
35
IC2009 qd (XTAL)
IC1009 1 (BOOT)
7
qd
3.7 Vp-p
39.6 ns
1 V/DIV, 20 ns/DIV
5 V/DIV, 2 s/DIV
IC2009 y; (BCK_OUT)
8
4.4 Vp-p
326 ns
1 V/DIV, 200 ns/DIV
– DISPLAY Board –
9
IC2009 ya (LRCLK_OUT)
wa
Q802 (Base)
4.3 Vp-p
20.8 s
1 V/DIV, 10 s/DIV
q;
IC2012 1 (BST)
24 Vp-p
3 s
5 V/DIV, 2 s/DIV
IC1002 qa (Xout)
qa
2.7 Vp-p
126 ns
1 V/DIV, 100 ns/DIV
IC3705 1 (BOOT)
qs
24 Vp-p
2.9 s
5 V/DIV, 2 s/DIV
HT-CT380/CT381
20.2 Vp-p
3 s
12 Vp-p
8 s
5 V/DIV, 5 s/DIV