Related Manuals for Hunt Electronic HTP?T2M20WXI
Summary of Contents for Hunt Electronic HTP?T2M20WXI
- Page 1 Hunt Electronic Inc HTP‐T2M20WXI 2.0 Megapixel IP PTZ Camera X20 Zoom CMOS User Manual ver.2.0...
-
Page 2: Safety Precaution
2.0 Megapixel IP X20 PTZ Camera User Manual Safety Precaution We appreciate your purchasing Megapixel IP PTZ camera. Before installing the product, please read the following with care Make sure to turn off the power before installing camera. Do not install under the direct sunlight or in dusty areas. Make sure to use the product within the temperature and humidity specified in the specification. -
Page 3: Table Of Contents
2.0 Megapixel IP X20 PTZ Camera User Manual Table of Content 1. Introduction .......................... 4 About this manual ....................... 4 Features ..........................4 Product and Accessories ...................... 6 Part Names and Functions ....................7 System Connections ......................8 2. Installation .......................... 10 DIP Switch Setup ...................... -
Page 4: Introduction
2.0 Megapixel IP X20 PTZ Camera User Manual 1. Introduction About this manual This User Manual provides information on operating and managing the megapixel IP PTZ camera. The Manual includes instructions of installation, operation and configuration of megapixel IP PTZ camera as well as how to make troubleshooting. - Page 5 2.0 Megapixel IP X20 PTZ Camera User Manual User Interface Diagnose and upgrade through dedicated program called True Manager System configuration using Internet Explorer High Reliability Reliable embedded system Powerful Pan/Tilt Functions Max. 360°/sec high speed Pan/Tilt Motion Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result, time to target view is reduced dramatically and the video on the monitor is very natural to watch.
-
Page 6: Product And Accessories
2.0 Megapixel IP X20 PTZ Camera User Manual Product and Accessories Main body & Dome Cover Accessories Main Cable Wrench Driver 2EA of BNC Cross LAN Cable Audio Cable Note: Mount Brackets are optional. Wall Mount Bracket Ceiling Mount Bracket [Screws : Torx Secrew M4×18, Hex Lag #14×50] [Screws : Torx Screw M4×18, Anchor Bolt 3/8"×70] 6/67... -
Page 7: Part Names And Functions
2.0 Megapixel IP X20 PTZ Camera User Manual Part Names and Functions ① Do not detach protection vinyl from dome cover before finishing all • Dome Cover installation process to protect dome cover from scratches or dust. Sets up camera ID and protocol. •... -
Page 8: System Connections
2.0 Megapixel IP X20 PTZ Camera User Manual System Connections IP Camera can be connected in either 1 to 1 connection where one camera is connected to one PC client or a decoder system or 1 to many connections where one camera can be connected to several PCs and decoder systems. - Page 9 2.0 Megapixel IP X20 PTZ Camera User Manual In this configuration, a site can be monitored from many remote central locations. Although up to 64 PCs or decoders can be connected to one camera, in the real network environment, network bandwidth can limit the maximum connections.
-
Page 10: Installation
2.0 Megapixel IP X20 PTZ Camera User Manual 2. Installation DIP Switch Setup When you control the camera through RS-485, before installation, you should set the DIP switches to configure the camera ID, communication protocol. Camera ID setup ID numbers of camera are set up with binary numbers.. See the examples shown below ID Value ex) ID=5... - Page 11 2.0 Megapixel IP X20 PTZ Camera User Manual Communication Protocol Setup Select the appropriate Protocol with DIP switch combination. Switch State Protocol/Baud rate (Pin 1) (Pin 2) (Pin 3) PELCO-D, 2400 bps PELCO-D, 9600 bps PELCO-P, 4800 bps PELCO-P, 9600 bps Otherwise Reserved If you want to control using DVR or P/T controller, their protocol must...
-
Page 12: Installation Camera With Brackets
2.0 Megapixel IP X20 PTZ Camera User Manual Installation Camera with Brackets Installation using Ceiling Mount Bracket ① Remove the ceiling tile from the ceiling and cut a ② Hook up “Drop Prevention Spring” on main body hole whose diameter is 30~40mm on the ceiling tile to prevent camera from unexpected drop and pull to pass the wire(s) and cable(s) through to the the wire(s) and cable(s) for the system as below... - Page 13 2.0 Megapixel IP X20 PTZ Camera User Manual Installation using Wall Mount Bracket ① Make a hole whose diameter is 30~40mm on the ② Hook up “Drop Prevention Spring” on main body to mounting surface to pass the wire(s) and cable(s) prevent camera from unexpected drop and pull the through the mounting surface.
-
Page 14: Wiring/Cabling & Connecting
2.0 Megapixel IP X20 PTZ Camera User Manual Wiring/Cabling & Connecting Port Description Main Cable Port Pin Number (RJ45) Connector / Wire Color Signal Black RS485 + Brown RS485 − DC 12V Orange Ground Yellow OUT COM (Relay Output Common) Green OUT 2 (Relay Output 2) Blue... - Page 15 2.0 Megapixel IP X20 PTZ Camera User Manual Connecting Power Carefully check the voltage and current capacity of the rated power. The rated power is indicated in the back of main unit. After confirming the power source, connect power adaptor and connect the 12V DC connector to the system For the DC input models, be careful with the polarity of DC power.
- Page 16 2.0 Megapixel IP X20 PTZ Camera User Manual Connecting Serial Port (RS-485 Communication) For PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple cameras to a single controller, RS-485 communication should be connected in parallel as shown below. If you are connecting a single camera to a controller, terminate the camera.
-
Page 17: Check If It Works
2.0 Megapixel IP X20 PTZ Camera User Manual Relay Output Internal AC or DC OUT COM OUT 1 LOAD OUT 2 LOAD Maximum allowable electrical load of relay is shown bellow table. Drive Power DC Power AC Power Max. Load Max DC 24V, 1A Max AC 125V, 0.5A Check if it works... -
Page 18: System Operation
2.0 Megapixel IP X20 PTZ Camera User Manual 3. System Operation Remote Video Monitoring There are two ways to monitor video when the center system and Megapixel PTZ Camera are connected. In order for a proper operation, an IP address must be set accordingly. Please refer to True Manager in Chapter 3 or Remote Setting in Chapter 4 for further details. - Page 19 2.0 Megapixel IP X20 PTZ Camera User Manual Video Select Select the Video stream to be viewed: Primary or Secondary This camera is capable of dual streaming; primary streaming and secondary streaming. Video will be displayed according to the resolution set on video configuration. If dual streaming (“Use Dual Encode”...
- Page 20 2.0 Megapixel IP X20 PTZ Camera User Manual Sensor Input Display the status of the sensor in real time. This camera supports two sensor inputs. When the sensor of the camera is working, the sensor light turns red. Alarm Output Operate the alarm device by pressing the number icon This camera supports two alarm outputs.
-
Page 21: Initialization Of Ip Address
2.0 Megapixel IP X20 PTZ Camera User Manual Video Monitoring with Decoder System Once camera’s IP address is set in the remote IP address section of the decoder, the decoder system will connect to camera and start receiving the video images. Normally, a monitor connected to the decoder will display video images Initialization of IP address If a system IP address is lost, the system can be reset to the system default IP address using the reset button... -
Page 22: Remote Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual 4. Remote Configuration Using Web Brower Remote setting is available by using web browser. Enter IP address of camera and then a live view screen appears as below. Press Setup button located in the upper right area of the monitoring screen to go to the server setup. -
Page 23: System Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual System Configuration 23/67... - Page 24 2.0 Megapixel IP X20 PTZ Camera User Manual General System ID Enter System ID that is used as a camera title The set System ID is displayed with video image on Web browser. The System ID is also transferred to remote software, such as VMS, and displayed on it.
- Page 25 2.0 Megapixel IP X20 PTZ Camera User Manual Config Backup & Restore Backup All the setting of configuration can be stored. Restore Stored configuration can be browsed and restored. The server is rebooted once Config Restore button is pressed. Time Start Time The latest the camera’s booting date and time Current Time...
- Page 26 2.0 Megapixel IP X20 PTZ Camera User Manual Automatically synchronize with NTP server Synchronize the camera time with an NTP server using NTP (network time protocol). Name of the NTP server should be registered on NTP server Name. The Network Time Protocol (NTP) is a protocol for synchronizing the clocks of computer systems over packet-switched, variable-latency data networks.
-
Page 27: Video Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual Video Configuration 27/67... - Page 28 2.0 Megapixel IP X20 PTZ Camera User Manual Encode Enable Preview Select ON to enable to display video on the monitor that is connected to the composite or HD-SDI video port. Select the Output format accordingly in the end of the Video page. Note that when Enable Preview is ON, dual streaming is not available.
- Page 29 2.0 Megapixel IP X20 PTZ Camera User Manual Bit rate Determine bitrate value between 32 ~ 8000kbps. Bitrate mode (CBR encoding) allows you to set a fixed target bitrate that consumes a predictable amount of bandwidth. In order to keep the bitrate limit, video quality is controlled dynamically according to the complexity or activity changes in the input video.
- Page 30 2.0 Megapixel IP X20 PTZ Camera User Manual Motion Detection Use Motion Detection Determine to use Motion Detection function Motion Detection on PTZ Allow disabling of motion detection when PTZ operation is performed. When it is set to Disable, motion detection is disable while the scene is changed due to PTZ control.
- Page 31 2.0 Megapixel IP X20 PTZ Camera User Manual BurnIn OSD Insert system ID and date/time in the compressed video. System ID and time respectively can be turned on or off in the video. Position and Font size can be configured also. System ID for BurnIn OSD exists independently from normal System ID.
-
Page 32: Audio Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual Audio Configuration Algorithm Algorithm Select the audio algorithm: G.711 or AAC G.711 and AAC from client to server direction are supported. Thus, bidirectional audio communication is supported. Bit rate Select the bitrate between 64Kbps and 128kbps when AAC is selected The sampling rate is fixed to 8KHz and 32KHz for G.711 and AAC respectively. - Page 33 2.0 Megapixel IP X20 PTZ Camera User Manual Input Gain Set audio input gain from 0 to 31. Audio Output Configure the audio source to be played on audio output port. Decoded Audio: Audio stream from client is played. Loopback: Audio data from audio input port is loop-backed to the audio output port. 33/67...
-
Page 34: Network Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual Network Configuration 34/67... - Page 35 2.0 Megapixel IP X20 PTZ Camera User Manual Local IP mode Select the IP mode: Fixed IP or DHCP (Dynamic Host Configuration Protocol) Depending on the selected mode, further configuration items come as follows IP Mode Selection Description Local IP Fixed IP address Local Gateway IP address...
- Page 36 2.0 Megapixel IP X20 PTZ Camera User Manual Port Base Port (1025 ~ 65535) Enter the Base Port number. Network base port is use for communication with remote clients. In order for camera and remote systems (decoder or VMS, NVR software) to be connected, the port number must be identically configured in camera side and client side.
- Page 37 2.0 Megapixel IP X20 PTZ Camera User Manual RTP (Real-Time Transport Protocol) is an Internet protocol used for transmitting single real-time multimedia data such as audio and video to a select group of connected clients. Normally RTSP uses RTP to format packets of multimedia content. RTP menu is used when the RTP only streaming without RTSP connection.
- Page 38 2.0 Megapixel IP X20 PTZ Camera User Manual SNMP Setup for using SNMP (Simple Network Management Protocol). It is compatible to both SNMPv1 and SNMPvec. Settings for using SNMP (Simple Network Management Protocol) are as following SNMP Listen Port(0, 161, 1025 ~ 65535): The port is for connecting external devices when system operates as a SNMP client.
- Page 39 2.0 Megapixel IP X20 PTZ Camera User Manual Check IP Disable: If “Check IP Disable” is selected, it will skip to check its own IP. In Fixed IP mode, the set IP will be registered on DDNS server. In DHCP mode, dynamically assigned IP will be registered on DDNS server.
-
Page 40: Serial Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual Serial Configuration 40/67... - Page 41 2.0 Megapixel IP X20 PTZ Camera User Manual Serial Port Configuration Serial Port Information This camera supports one RS-485 serial port The serial port of camera is configured with the DIP switch in the camera. Serial Port Information section just displays the information.
- Page 42 2.0 Megapixel IP X20 PTZ Camera User Manual To set all cells in the schedule, click below “Empty Cell”. 42/67...
-
Page 43: Event Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual Event Configuration 43/67... - Page 44 2.0 Megapixel IP X20 PTZ Camera User Manual This camera has two sensor ports and two alarm ports. When a decoder instead of a PC client is connected to camera, one system becomes a Local system and the other a Remote system (Generally a system which is being used by the user is called as Local system).
- Page 45 2.0 Megapixel IP X20 PTZ Camera User Manual E-mail Notification Specify the information to send event information, when E-mail is selected as an event action. Server Address Enter an address of mail(SMTP) server Port Specify a port for SMTP operation (Port 25 is the default port in SMTP operation. If a different port is configured in the SMTP server, this port needs to be changed accordingly).
- Page 46 2.0 Megapixel IP X20 PTZ Camera User Manual Message Description Test E-mail has been sent successfully. Reception in the client E-mail sent successfully can be checked. Failed to connect SMTP Connection to the SMTP server failed. It is necessary to check if server the server is reachable and server address and port are correct.
- Page 47 2.0 Megapixel IP X20 PTZ Camera User Manual FTP Upload Specify the information to upload event information, when FTP is selected as an event action’ Server Address Enter an address of an FTP server to receive video files Port Specify a port for FTP operation (Port 21 is the default port in FTP operation. If a different port is configured in the FTP server, this port needs to be changed accordingly).
- Page 48 2.0 Megapixel IP X20 PTZ Camera User Manual Number of Frame Enter frame number of JPEG Capture (from 1 to 10). Continuous Upload Continuous upload ‘On’ allows video clips to be transmitted regularly regardless of occurrence of events. When this mode is turned on, FTP upload by events is suppressed. Upload Duration Specify recording duration of a video clip to be transmitted.
-
Page 49: Ptz Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual PTZ Configuration 49/67... - Page 50 2.0 Megapixel IP X20 PTZ Camera User Manual Circular plate provides panning and tilting functions combined with speed control. Clicking a mouse on a position of the circular plate determines the speed of the control as well as the direction. Mask Masks can be displayed in the video.
- Page 51 2.0 Megapixel IP X20 PTZ Camera User Manual Swing By using swing function, you can make camera to move between 2 preset positions repeatedly. When swing function runs, camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction.
- Page 52 2.0 Megapixel IP X20 PTZ Camera User Manual Group This function is that the camera memorizes the combination of Presets, Pattern and/or Swings sequentially and runs Presets, Pattern and/or Swings repetitively on activation. Max 8 groups are programmable. Each group can have max 20 actions which are the combinations of Preset, Pattern and Swing.
- Page 53 2.0 Megapixel IP X20 PTZ Camera User Manual Using Pattern/Swing/Group in Live view page Pattern, Swing or Group which is configured on PTZ page can be activated in Live view page. Select an entry in the list. 8 entries are valid for Swing and Group, while 4 entries are valid for Pattern. Press the button for the function to activate.
-
Page 54: Record Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual Record Configuration 54/67... - Page 55 2.0 Megapixel IP X20 PTZ Camera User Manual DISK SD memory can be used, and at least 1GB size is recommended. Either EXT3 or FAT32 file system can be used. A disk with either EXT3 or FAT32 file system can be read in Linux PC. However, only disk with FAT32 file system can be read in Windows PC.
- Page 56 2.0 Megapixel IP X20 PTZ Camera User Manual General Use record Off: Recording function will not be used when “Off” is selected Use Disk: Recording will be enabled and data will be written to a disk Use FTP: Recording will be enabled and data will be uploaded to an FTP server. In this mode FTP upload by event is automatically disabled.
- Page 57 2.0 Megapixel IP X20 PTZ Camera User Manual FTP Base Directory Specify the name of the directory to be created in the FTP server. It is valid only when Use Record is set to Use FTP. Event Type Three recording modes are supported: Continuous, Event, Disconnect. In case of Event recording, event types can be selected among several events.
- Page 58 2.0 Megapixel IP X20 PTZ Camera User Manual Search and Playback Recorded video and audio data can be saved as AVI format in the disk. In general, one AVI file is created for an event in case of event-based recording. However, it is possible that recorded data by serious of events happening continuously can be merged to a single AVI file depending on pre/post event time setting.
- Page 59 2.0 Megapixel IP X20 PTZ Camera User Manual Playback Selecting an AVI file will show a dialog for opening or saving the file Pressing Save button, the file will be stored in the PC. The AVI file can be played with Windows Media Player.
- Page 60 2.0 Megapixel IP X20 PTZ Camera User Manual Deletion of data If you want to delete recorded files, select the files by checking the item in front of each file and press Delete button. It is possible to delete multiple files at once. 60/67...
-
Page 61: User Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual User Configuration User List User can be registered and privilege level of a user can be specified. User configuration is allowed only to admin user. Max 16 users can be registered and each user can have one of four privileges. Privilege Allowed Operations Remarks... - Page 62 2.0 Megapixel IP X20 PTZ Camera User Manual Delete User Select the User to be deleted and press Delete button. Change Password .Press Modify Password button. The following window will appear. Enter the current password and then set a new password. Modify Privilege Level Press Modify Privilege button to change User level.
-
Page 63: Camera Configuration
2.0 Megapixel IP X20 PTZ Camera User Manual Camera Configuration 63/67... - Page 64 2.0 Megapixel IP X20 PTZ Camera User Manual Day & Night The camera delivers color images during the day. As light diminishes below a certain level, the camera can automatically switch to night mode (Black & White mode) to maintain good image quality. Day &...
- Page 65 2.0 Megapixel IP X20 PTZ Camera User Manual Back Light Compensation It is an ability of a camera to balance the lighting in a scene with an extremely bright background such as sunlight. It helps to obtain the finest light contrast and get clear image. Digital Zoom Determine to use Digital zoom (12x) supported by the camera zoon lens.
- Page 66 2.0 Megapixel IP X20 PTZ Camera User Manual Max Jog Speed Adjust Max Pan Speed (8 Steps) Max Zoom Speed Adjust Max Zoom Speed (8 Steps) Display PTZ Action PTZ control action such as Preset Goto, Pattern, Swing or Group can be displayed on the top of live display.
- Page 67 2.0 Megapixel IP X20 PTZ Camera User Manual Scheduling Configurations In order to allow different configurations of the camera according to time of a day, the feature of defining camera configurations and scheduling them is provided.. Configuration Set 4 different configuration sets can be configured by opening the page with Config Set#N buttons. For example, Config Set#1 can be configured for day mode, and Config Set#2 can be configured for night mode.
Need help?
Do you have a question about the HTP?T2M20WXI and is the answer not in the manual?
Questions and answers