Burstner Trecento 2011 Owner's Manual
  1. Manuals
  2. Brands
  3. Burstner Manuals
  4. Motorhomes
  5. Trecento 2011
  6. Owner's manual

Burstner Trecento 2011 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction manual
Dear Reader ...
Instruction manual
We would like to congratulate you on the purchase of your new caravan. You have selected a top-quality
vehicle which will afford you many years of enjoyment.
To enable you to always use and operate your caravan properly and easily, your Bürstner dealer will first pro-
vide you detailed instructions for all important functions when you take delivery.
This manual, as well as the instruction manuals from the appliance manufacturers are your constant travelling
companions and will help answer any questions you may have regarding your caravan.
Before your first journey
Please familiarise yourself with this manual rather than relying on it strictly for reference.
Fill in the warranty cards for the appliances and special equipment in the individual instructions and send these
cards to the respective manufacturers. This ensures your warranty claim for each appliance.
© 2010 Bürstner GmbH Kehl
Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Trecento 2011 and is the answer not in the manual?

Questions and answers

Related Manuals for Burstner Trecento 2011

Summary of Contents for Burstner Trecento 2011

  • Page 1 Instruction manual Dear Reader ... Instruction manual We would like to congratulate you on the purchase of your new caravan. You have selected a top-quality vehicle which will afford you many years of enjoyment. To enable you to always use and operate your caravan properly and easily, your Bürstner dealer will first pro- vide you detailed instructions for all important functions when you take delivery.
  • Page 2 Instruction manual Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 3: Table Of Contents

    Contents Introduction 230 V connection ....37 ....7 Refrigerator .
  • Page 4 Contents 6.11.4 Fixed bed (adjustable head 9.2.1 Models with waste gas vent on the section) ......62 right-hand side of the vehicle .
  • Page 5 Contents 10.7.1 Swivel toilet (Thetford C-200) ..127 12.9.2 Recessed halogen light (flat) ..159 10.7.2 Toilet with fixed seat 12.9.3 Recessed halogen light ... 160 (Thetford C-402) .
  • Page 6 Contents Technical data ....187 16.1 Table of linear measures ..187 16.2 Power supply ....187 Helpful notes .

  • Page 7: Introduction

    Introduction Please read this instruction manual completely before 1Introduction using the vehicle for the first time! Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. The non-observance of this symbol can lead to personal injury. ...

  • Page 8: General

    Introduction General The vehicle is constructed in accordance with the latest technology and the recognised safety regulations. Nevertheless, personal injury may result and the vehicle may be damaged if the safety instructions in this instruction manual are not followed. Only use the vehicle in a technically impeccable condition. Follow the instruc- tions in the instruction manual.
  • Page 9 Introduction When staying in towns and communities for long periods, search for  parking areas which are specially reserved for caravans and towing vehi- cles. Enquire at the town or community authority about parking spaces. Always leave the parking places in a clean condition. ...
  • Page 10 Introduction Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 11: Safety

    Safety Chapter overview 2Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: fire prevention and what to do in case of fire  general care of the vehicle ...

  • Page 12: General

    Safety All windows and doors which meet the following requirements are considered as emergency exits: Open to the outside or can be shifted in horizontal direction  Opening angle at least 70°  Minimum diameter of clearance = 450 mm ...

  • Page 13: Towing

    Safety In case of underpasses, tunnels or similar obstacles, note the total  height of the vehicle (including the roof load). In winter, the roof must be free of snow and ice before commencing the  journey. Before commencing the journey, empty the waste water tank. ...

  • Page 14: Gas System

    Safety Gas system 2.5.1 General instructions Before commencing the journey, when leaving the vehicle or when gas  equipment is not in use, close all gas isolator taps and the main isolator tap on the gas bottle. No appliance operated by a naked flame (e.g. heater or refrigerator) may ...

  • Page 15: Gas Bottles

    Safety Do not use the gas bottle compartment as storage space as it is not  moisture-proof. Secure the gas bottle compartment against unauthorised access. To do  this, lock the compartment. The regulator tap on the gas bottle must be accessible. ...

  • Page 16: Water System

    Safety Only replace defective fuses when the cause of the defect is known and  has been remedied. Never bridge or repair fuses.  Water system Water left standing in the water tank or in the water pipes becomes  undrinkable after a short period.

  • Page 17: Before The Journey

    Before the journey Chapter overview 3Before the journey This chapter contains important information which has to be noted before com- mencing your journey or carrying out any tasks before the journey. The instructions address the following topics: keys  registration ...

  • Page 18: Connecting

    Before the journey Connecting Care is to be taken when connecting and detaching a trailer. Risk of acci-  dent and injury! No persons are to be between the towing vehicle and the trailer during  positioning for connecting and detaching. Observe the permissible nose weight and rear axle load of the towing ...

  • Page 19: Caravan Couplings

    Before the journey Caravan couplings Before connecting, ensure that the tow ball of the coupling device is free of  dirt and grease. 3.4.1 AKS 1300 stabiliser Fig. 2 AKS 1300 stabiliser Connecting: Pull up the stabilising lever (Fig. 2,1) as far as possible. ...

  • Page 20: Ws 3000 D Stabiliser

    Before the journey In addition, push the coupling handle downwards by hand (not with your  foot). Closing and securing is carried out automatically. Conduct a visual inspection: The green cylinder on the safety indicator  (Fig. 3,3) must be visible. Activate the stabilising mechanism.

  • Page 21: Caravan Control System

    Before the journey Fig. 5 Hitching device Easy-Pull Connecting the caravan: Drive up to the caravan with the towing vehicle.  Push the locking lever (Fig. 5,2) to the open position.  Pull the belt with the hook (Fig. 5,5) out towards the front, lay it around the ...

  • Page 22: Caravan Control System (Idc) (Special Equipment)

    Before the journey 1 Control LED Fig. 6 Control LED Couple caravan.  Use the connection cable to connect the caravan to the towing vehicle. The  caravan control system starts a self test. The control LED (Fig. 6, 1) on the caravan lights up red for about 3 seconds.

  • Page 23: Payload

    Before the journey Detaching: Apply the caravan handbrake.  Place the wheel chocks behind both of the wheels.  Remove the connector plug of the caravan from the towing vehicle socket  and insert it in the holder on the drawbar. Remove the breakaway cable from the towing vehicle.
  • Page 24 Before the journey Maximum permissible The maximum permissible gross weight in a laden condition is the weight that gross weight in a laden a vehicle may never exceed. condition The maximum permissible overall weight in laden condition consists of the mass in ready-to-drive condition and of the payload.

  • Page 25: Calculating The Payload

    Before the journey Additional equipment Additional equipment includes accessories and special equipment. Examples of additional equipment include: Spare wheel  Bike rack  Satellite unit  Microwave oven  Hot water supply  Chapter 15 lists the weights of the various items of special equipment; they may also be obtained from the manufacturer.

  • Page 26: Loading The Caravan Correctly

    Before the journey The payload (see section 3.8.1) is the difference in weight between Maximum permissible gross weight in a laden condition and  Vehicle mass complete in a ready-to-drive condition.  Mass in kg to be Calculation calculated Example for calculating Maximum permissible gross weight ac- 1500 cording to vehicle documents...

  • Page 27: Caravan Load, Nose Weight And Axle Load

    Before the journey Fig. 7 Incorrect weight distribution Incorrectly loaded Loads stored apart from each other (Fig. 7) lead to inclination to skid. Fig. 8 Correct weight distribution Correctly loaded Do not store heavy objects such as awnings, tin cans, etc. in the caravan but rather in the towing vehicle.

  • Page 28: Bike Rack (Special Equipment)

    Before the journey Caravan load The caravan load (Fig. 9,1) stipulated in the towing vehicle documents pro- vides information as to the maximum weight which the towing vehicle is per- mitted to tow. The caravan load refers to the actual weight of the caravan and not to the maximum permissible gross weight of the caravan.
  • Page 29 Before the journey Fasten bicycles using the straps provided and check to see that they are  secure after you have driven a few kilometres. Check the secure attachment of the bicycles on the bike rack after the  first 10 km and then at each break in the journey. Do not use the bike rack as luggage rack or ladder.

  • Page 30: External Mirrors

    Before the journey Fig. 11 Bike rack on the rear wall Loading the bicycles: Put the bikes onto the bike rack and secure them with quick straps.  In addition, secure each bicycle on the retaining bracket or retaining arm. ...

  • Page 31: Television (Special Equipment)

    Before the journey 3.10 Television (special equipment) Before commencing the journey, remove the television from the support  and store it securely. Before commencing the journey, place and secure the flat screen and  screen support in the initial position. If the screen holder is installed in a TV cabinet: Close TV cabinet.
  • Page 32 Before the journey Checks Checked External flaps closed and locked Conversion door locked Housing body, inside Windows and skylights closed and locked Television removed from the support and securely stored Flat screen secured Television antenna retracted (if one is built in) Loose parts stored away or fixed in position Open storage spaces empty No gas cartridges or other easily flammable materials stored in...

  • Page 33: During The Journey

    During the journey Chapter overview 4During the journey This chapter contains instructions on how to drive the caravan. The instructions address the following topics: driving speed  brakes  driving in reverse  Driving with the caravan During the journey, no persons are to travel inside the caravan. ...
  • Page 34 During the journey Fig. 13 Approach Fig. 14 Steer to the left Driving in reverse: Drive up to the entrance until the rear of the caravan is roughly level with  the entrance (Fig. 13). Steer the stationary towing vehicle and trailer to the left (Fig. 14). ...

  • Page 35: Pitching The Caravan

    Pitching the caravan Chapter overview 5Pitching the caravan This chapter contains instructions on how to pitch the vehicle. The instructions address the following topics: handbrake  wheel chocks  operation of the supports  entrance step  mobile waste water tank ...

  • Page 36: Entrance Step (Free-Standing)

    Pitching the caravan With the assistance of the jockey wheel position the pitched caravan in a hor- izontal position. For control purposes use a small spirit level. Crank down the corner steadies after the caravan is in an absolutely horizontal position.

  • Page 37: Waste Water Tank, Mobile (Special Equipment)

    Pitching the caravan Waste water tank, mobile (special equipment) Fig. 21 Waste water tank, mobile The waste water tank (Fig. 21,1) is stored inside the caravan gas bottle com- partment during the journey. The drain pipe (Fig. 21,3) of the caravan is located at the bottom of the vehicle - on the left hand side in the direction of travel.

  • Page 38: Equipment With Semi-Automatic Antenna Alignment

    Pitching the caravan Fig. 22 Remote control Setting up the unit: Switch on the television.  Press the key " " (Fig. 22,2) on the remote control.  The satellite antenna repositions itself out of the park position and into search mode.
  • Page 39 Pitching the caravan Turn antenna slowly. When the antenna finds the satellite, you will hear a  signal tone. Optimise the reception by turning and tilting the antenna.  Slightly retighten the antenna mast clamp.  Lowering the antenna for Loosen antenna mast clamp.
  • Page 40 Pitching the caravan Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 41: Living

    Living Chapter overview 6Living This chapter contains instructions about living in the vehicle. The instructions address the following topics: opening and closing the doors and external flaps  light switches  adjusting the halogen spotlights  positioning the television  heating the vehicle ...

  • Page 42: Conversion Door, Inside

    Living 6.1.2 Conversion door, inside Fig. 25 Door lock, conversion door, inside Opening: Push the handle (Fig. 25,1) down.  Locking: Turn the handle (Fig. 25,1) approx. 45° upward and leave it in this position.  6.1.3 Window conversion door (Seitz) (special equipment) The conversion door window is fitted with a Roman shade.

  • Page 43: External Flaps

    Living Fig. 27 Insect screen Closing: Pull out the insect screen completely by the bar (Fig. 27,1).  Opening: Push the insect screen into its initial position by the bar (Fig. 27,1).  External flaps Before commencing the journey, close all external flaps and lock them. ...

  • Page 44: Flap Lock, Rectangular

    Living Closing: Firmly close the external flap.  Turn lock handle in a clockwise direction until it is horizontal. The flap lock  is now engaged but not locked. Insert key into locking cylinder.  Press down lock handle with key inserted and turn key a quarter turn in a ...

  • Page 45: Flap For Toilet Cassette

    Living 6.2.3 Flap for toilet cassette Fig. 30 Flap for toilet cassette Opening: Insert key into locking cylinder (Fig. 30,1) of the push-button lock and turn  a quarter turn. Remove the key.  Press both push-button locks (Fig. 30,2) simultaneously with your thumb ...

  • Page 46: Cap For The Drinking Water Filler Neck (Only For Water Tank 40 L)

    Living 6.2.5 Cap for the drinking water filler neck (only for water tank 40 l) Fig. 32 Cap for the drinking water filler Fig. 33 Cap for the drinking water filler neck neck (alternative) The drinking water filler neck is labelled by the word "WASSER" (water) ...

  • Page 47: Furniture Flaps With Handle

    Living Closing: Press furniture flap shut.  Press push button in until it locks. The furniture flap is closed correctly  when the fastener locks into place. 6.3.2 Furniture flaps with handle Fig. 35 Furniture flap with handle (example) Opening: Pull handle (Fig.

  • Page 48: Light Switch

    Living Light switch 6.4.1 Entrance area Fig. 37 Light switch Fig. 38 Awning light The entrance area has light switches for the following lamps: Seating group lighting (Fig. 37,1)  Awning light (Fig. 37,2 and Fig. 37,3)  For models without the light switch (Fig. 37,2) the awning light (Fig. 38) is ...

  • Page 49: Holder For Flat Screen

    Living Fig. 41 Cooker lamp Fig. 42 Living area lamps, light switch separate from the lamp The light switches in the living area are located directly on the corresponding lamp (Fig. 41,1) or in the seating group (Fig. 42,1) or the bed area. Holder for flat screen Before commencing the journey, place and secure the flat screen and ...

  • Page 50: Holder In The Tv Cabinet

    Living 6.5.2 Holder in the TV cabinet The flat screen is attached to a console in the TV cabinet. Fig. 44 Holder in the TV cabinet Positioning: Push the unlocking bar (Fig. 44,1) in.  Pull out the extension (Fig. 44,2) as far as possible. ...

  • Page 51: Windows

    Living Condensation Ensure that there is a continuous exchange of air by providing frequent and efficient ventilation. This is the only method for ensuring that condensation and resulting mould is not formed during cool weather. During the colder season, a pleasant living climate is created if heating output, air distribution and venti- lation are synchronised.
  • Page 52 Living Fig. 45 Catch lever in "closed" position Fig. 46 Hinged window with rotary hinges, open Opening: Turn the catch lever (Fig. 45,3) a quarter turn towards the centre of the  window. Open the hinged window until the required position has been reached and ...

  • Page 53: Hinged Window With Automatic

    Living 6.8.2 Hinged window with automatic hinges Open the window completely, to release the lock. If the locking device is  not released and the window is closed nevertheless, there is the danger of the window breaking due to the massive counter-pressure. When opening the hinged windows, ensure that there are no torsional ...

  • Page 54: Blind And Insect Screen

    Living To place the hinged window into the "continuous ventilation" position: Turn the catch lever (Fig. 50,3) a quarter turn towards the centre of the  window. Slightly open the hinged window outwards.  Turn the catch lever a quarter turn towards the window frame. The locking ...

  • Page 55: Roman Shade And Insect Screen (Special Equipment)

    Living Insect screen The insect screen is located in the upper blind box. Closing: Pull insect screen at the handle (Fig. 51,1) down and hang it into the  locking devices (Fig. 51,3) situated on both sides of the window frame. Opening: Press handle (Fig.

  • Page 56: Heki Skylight (Mini And Midi) (Partially Special Equipment)

    Living The skylights are fitted with a blind or Roman shade and with an insect  screen or folding insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force.

  • Page 57: Heki Skylight (Partially Special Equipment)

    Living Fig. 55 Heki skylight in ventilation Fig. 56 Ventilation position locking position mechanism Ventilation position The Heki skylight can be put in two ventilation positions: Bad weather position (Fig. 55,1) and central position (Fig. 55,2). Depending on the model, the sky- light can be locked in the central position with the latch (Fig.
  • Page 58 Living Opening: Press the safety knob (Fig. 57,1) and turn the catch lever (Fig. 57,2) one  quarter turn inward. Pull the bar (Fig. 57,4) downwards out of the latch.  Press the Heki skylight upwards using the bar.  Press the bar back into the latch.

  • Page 59: Tables

    Living Opening: Hold the blind screen by the handle with one hand.  With your other hand, push the unlocking bar on the handle of the insect  screen (Fig. 60,1) towards the handle. The lock is released. Use handle to return the blind slowly to its initial position. ...

  • Page 60: Lift-Off Table, Rotatable

    Living 6.10.2 Lift-off table, rotatable Fig. 63 Lift-off table, rotatable The top of the lift-off table can be rotated. Rotating table-top: Loosen knurled screw (Fig. 63,3).  Rotate table-top (Fig. 63,2) to the required position.  Retighten the knurled screw. ...

  • Page 61: Fixed Bed (Manual Setup)

    Living 6.11.2 Fixed bed (manual setup) Do not let the slatted frame fall down when closing the bed!  Fig. 64 Fixed bed The bedding box is located underneath the bed. The bedding box may be used to store bedding. Fold up the slatted frame to place items in the bedding box or to empty it.

  • Page 62: Fixed Bed (Adjustable Head Section)

    Living Closing: Press the slatted frame downwards against the resistance of the gas-pres-  sure springs. If necessary, push the mattress behind the panel.  6.11.4 Fixed bed (adjustable head section) Do not let the slatted frame fall down when closing the bed! ...

  • Page 63: Widening Single Beds (Special Equipment)

    Living 6.11.5 Widening single beds (special equipment) 1 Mattress 2 Bedside locker cover 3 Bedside locker extension 4 Slatted frame 5 Additional cushion 6 Additional cushion Fig. 67 Prior to conversion Fig. 68 During conversion Fig. 69 After conversion Remove the bedside locker cover (Fig. 67,2) and put it to one side. ...

  • Page 64: Converting Seating Groups For

    Living 6.12 Converting seating groups for sleeping 6.12.1 Bench and central seating group without additional cushion 1 Back cushion 2 Seat cushion 3 Table Fig. 70 Prior to conversion Fig. 71 After conversion Convert the table (Fig. 70,3) to a bed foundation (see section 6.10). ...

  • Page 65: Round Seating Group With Square

    Living 6.12.2 Round seating group with square table Depending on the model, the seating group can be different in shape and  position to the one shown here. 1 Back cushion 2 Seat cushion 3 Table 4 Back cushion 5 Back cushion 6 Additional cushion (basic or foldable) Fig.

  • Page 66: Round Seating Group Without Additional Cushion

    Living 6.12.3 Round seating group without additional cushion Depending on the model, the seating group can be different in shape and  position to the one shown here. 1 Back cushion 2 Seat cushion 3 Table 4 Seat cushion 5 Back cushion 6 Back cushion 7 Back cushion 8 Back cushion...

  • Page 67: Round Seating Group With Additional Cushion (Foldable)

    Living 6.12.4 Round seating group with additional cushion (foldable) Depending on the model, the seating group can be different in shape and  position to the one shown here. 1 Back cushion 2 Seat cushion 3 Table 4 Back cushion 5 Back cushion 6 Additional cushion (foldable) Fig.

  • Page 68: Rear Seating Group

    Living 6.12.5 Rear seating group 1 Back cushion 2 Seat cushion 3 Table 4 Back cushion 5 Seat cushion 6 Back cushion 7 Seat cushion 8 Additional cushion (foldable) Fig. 81 Prior to conversion Fig. 82 During conversion Fig. 83 After conversion Convert the table (Fig.

  • Page 69: Gas System

    Gas system Chapter overview 7Gas system This chapter contains instructions regarding the gas system of the vehicle. The instructions address the following topics: safety  changing the gas bottles  gas isolator taps  external gas connection  automatic switching facility ...

  • Page 70: Gas Bottles

    Gas system Propane gas is capable of gasification up to -42 °C, whereas butane gas  gasifies at 0 °C. Below these temperatures no gas pressure is available. Butane gas is unsuitable for use in winter. Regularly inspect the gas tube fitted to the gas bottle connection for ...

  • Page 71: Changing Gas Bottles

    Gas system Use the shortest possible tube lengths (150 cm max.) for external gas  bottles. Never block the floor ventilation openings below the gas bottles.  For gas-operated units the gas pressure must be reduced to 30 mbar.  Connect gas pressure regulator complete with safety valve directly to bottle ...

  • Page 72: Gas Isolator Taps

    Gas system Gas isolator taps 1 Cooker 2 Boiler (special equipment) 3 Oven (special equipment) 4 Refrigerator 5 Heater Fig. 85 Symbols for the gas isolator taps A gas isolator tap (Fig. 85) for every gas device is built into the vehicle. The gas isolator taps are located behind a flap in the kitchen area.

  • Page 73: Duocontrol Switching Facility (Special Equipment)

    Gas system Connect the external gas device to the connection point (Fig. 86,1).  Open the gas isolator tap (Fig. 86,2).  DuoControl switching facility (special equipment) Do not use the switching facility in closed spaces.  Also read the manufacturer's instruction manual. ...

  • Page 74: Gas Alarm System (Special Equipment)

    Gas system Putting into operation: Open the regulator taps on the gas bottles (Fig. 87,1 and 6).  Use the knob (Fig. 87,4) on the reversing valve (Fig. 87,3) to select the gas  bottle which is to be the primary source of gas (primary bottle). Always turn the knob as far as it will go.
  • Page 75 Gas system Fig. 89 Gas sensor The flashing LED (Fig. 89,2) next to the terminal block of the gas sensor (Fig. 89,1) indicates readiness for operation. Switching off the buzzer: Briefly switch off the 12 V power supply and switch it on again (e.g. on the ...
  • Page 76 Gas system Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 77: Electrical System

    Electrical system Chapter overview 8Electrical system This chapter contains instructions regarding the electrical system of the vehicle. The instructions address the following topics: safety  explanations of terms relating to the battery  12 V power supply  power supply unit ...

  • Page 78: Power Supply Unit Csv 400-1

    Electrical system When the caravan is not connected to the 230 V power supply, 12 V power supply is performed either by the starter battery of the connected towing vehicle or by the living area battery (electric kit). The starter battery has a limited power supply only. For this reason, the elec- trical appliances should not be operated for a long time without using the 230 V power supply when the engine of the towing vehicle is switched off.

  • Page 79: Electric Kit (Special Equipment)

    Electrical system Electric kit (special equipment) Scope The following components belong to the electric kit: Battery 12 V, 90 or 110 Ah  Battery charging unit  Panel  Booster  The multi-function power supply (EVS) is a product of the most modern switched-mode power supply technology.

  • Page 80: Charging Procedure For The Living Area Battery

    Electrical system 8.5.3 Charging procedure for the living area battery Power operation If the mains connection has been made, the EVS works as a power supply during mains operation. The EVS has an electronic protection against incor- rect polarity. The charging current is only supplied if the battery is correctly connected and a minimum voltage of 1.5 V is present.
  • Page 81 Electrical system When leaving the vehicle, switch off the main 12 V power supply from the  panel. This prevents any unnecessary discharge of the living area battery. The power supply unit then only supplies a current, if the battery is con- ...
  • Page 82 Electrical system Connection diagram Fig. 92 Connection diagram 1 Fig. 93 Connection diagram 2 Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 83: Power Supply

    Electrical system 230 V power supply Only allow qualified personnel to work on the electrical system.  The 230 V power supply provides electricity for: sockets with earth contact for appliances with maximum 16 A  refrigerator  power pack or power supply unit ...

  • Page 84: Fuses

    Electrical system Fig. 94 Connection possibilities 230 V Fig. 95 Connecting an angled con- connection nector with socket Adapter cable:  CEE 17 socket with earth contact (Fig. 94,1) – plug with earth contact (Fig. 94,2) Cable reel:  Socket with earth contact (Fig. 94,3) – plug with earth contact (Fig. 94,4) Adapter cable: ...
  • Page 85 Electrical system 1 Unbroken fuse element 2 Broken fuse element Fig. 96 12 V fuse An intact 12 V fuse can be detected by the unbroken fuse element (Fig. 96,1). If the fuse element is broken (Fig. 96,2), change the fuse. Before changing fuses, take the function, value and colour of the relevant fuses from the following specifications.

  • Page 86: 230 V Fuse

    Electrical system Fuse for the Thetford The fuse is located in the locker wall of the Thetford cassette. toilet (fixed seat) 1 Flat fuse 3 A/purple Fig. 98 Fuse for the Thetford toilet Changing: Open the flap for the Thetford cassette on the outside of the vehicle. ...

  • Page 87: Thirteen-Pin Plug Connection Diagram

    Electrical system Thirteen-pin plug connection diagram Note the colours of the connecting cable of the socket which is fitted to the  towing vehicle. This makes any new connection which may be necessary easier. To connect the thirteen-pin plug to a seven-pin socket, use a commercially ...

  • Page 88: External Socket (Special Equipment)

    Electrical system Contact DIN- Function Cable Cross number specifi- colour section of cation the wire Earth charging line Orange- 2.5 mm white Not assigned – – Earth (contacts 9 - 12) Blue- 2.5 mm white These earth cables may not be connected to electrical conductors on the trailer side.

  • Page 89: Circuit Diagrams

    Electrical system 8.10 Circuit diagrams 8.10.1 Circuit diagram, interior Fig. 104 Circuit diagram, interior Towing vehicle connecting cable (external fuse max. 15 A) Refrigerator 12 V indicator (panel) Refrigerator control Water pump Circuit 1 Circuit 2 Circuit 3 10 Awning light 11 Spare 12 Circuit 5 Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 90: Circuit Diagram, Exterior

    Electrical system 8.10.2 Circuit diagram, exterior Cable installation can differ depending on the model.  Fig. 105 Circuit diagram, exterior Side marking light (number depends on type) Left direction indicator (yellow) Fog tail light (grey) Earth 1 - 8 (white) Right direction indicator (green) Brake lights (red) Right tail light (brown)

  • Page 91: Appliances

    Appliances Chapter overview 9Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction man- uals for the appliances, included separately with the vehicle. The instructions address the following topics: heater ...

  • Page 92: Heater

    Appliances Heater In winter, check that the waste gas vent on the vehicle roof is free of  snow and ice before using the heater. Never let gas escape unburned due to danger of explosion.  When filling the fuel tank of the towing vehicle, on ferries or in the ...

  • Page 93: Hot-Air Heater

    Appliances Adjusting the air outlet Fully open: Full hot air stream  nozzles Half or partially open: Reduced hot air stream  When five air outlet nozzles are completely opened, less warm air escapes through each nozzle. However, if only three air outlet nozzles are opened, more warm air flows out of each nozzle.

  • Page 94: Circulation Fan

    Appliances Fig. 109 Removing heater cover Fig. 110 Heater opened Changing the battery on the Make certain that the heater is switched off.  automatic ignition: Remove heater cover (Fig. 109,2). Pull the heater cover upwards and for-  wards, press up the retaining springs (Fig. 109,1) to the side and tip the cover forwards.

  • Page 95: Airmix Comfort Package (Special Equipment)

    Appliances Fig. 112 Operating switch for circulation Switching circulation fan on: Set sliding switch (Fig. 112,1) to " " (manual control) or "A" (automatic  operation). Turn the knob (Fig. 112,2) to set (manual control) or limit (automatic oper-  ation) the power of the circulation fan.

  • Page 96: Alde Hot-Water Heater

    Appliances 9.2.6 Alde hot-water heater Never run hot-water heater without heating fluid. Observe notes in  chapter 12. Never drill holes in the floor. This might damage the hot-water pipes.  The circulating pump must always be turned on when the hot-water heater ...
  • Page 97 Appliances Start screen The Start screen appears on the display after the heater is switched on. The Start screen contains the following information: Symbol Signification This symbol appears when the circulating pump is activated This symbol appears when a switching facility for gas cylinders is activated This symbol appears when a voltage of 230 V is present at the heater...

  • Page 98: Ultraheat Additional Electric Heater (Special Equipment)

    Appliances If gas and 230 V electrical operation is selected and if the vehicle is con-  nected to the 230 V power supply, then the hot-water heater at first only operates in 230 V electric operation. Only if the heat output is insufficient does the gas operation also automatically switch on.

  • Page 99: Warming Unit For Waste Water Pipes (Special Equipment)

    Appliances 9.2.8 Warming unit for waste water pipes (special equipment) Always only press the test button briefly.  The warming unit only functions when the vehicle is connected to a 230 V  power supply. In order to prevent waste water pipes freezing up, the waste water pipes can be electrically warmed.

  • Page 100: Electrical Floor Warming Unit (Special Equipment)

    Appliances 9.2.9 Electrical floor warming unit (special equipment) On models with electrical floor warming unit, never drill holes in the floor  or screw in any screws. Careful with sharp objects. There is danger of a power cut or a short circuit due to damage to a heater wire. Do not cover the transformer.
  • Page 101 Appliances In the winter, vehicle heating can be supported but not replaced by the air  conditioning unit. Also read the manufacturer's instruction manual.  Symbol for automatic mode Symbol for cold mode Symbol for warm mode Symbol for ventilation mode Symbol for discharged batteries Time Temperature display...

  • Page 102: Telair

    Appliances The LED (Fig. 120,4) on the ceiling unit (Fig. 120,1) displays the operating status of the air conditioning unit: Status LED Signification Air conditioning unit off Orange Air conditioning unit ready to operate Green Air conditioning unit in operation Red (continuous) No 230 V power connection Red (flashes once intermit-...

  • Page 103: Boiler

    Appliances 1 Mains connection indicator lamp 2 Temperature (current) display 3 Mode indicator lamp Green: Cooling Red: Heater Fig. 122 Display on the diffusor To execute the individual switching commands, always point the remote con- trol in the direction of the receiver. Operating modes Automatic ...

  • Page 104: Models With Waste Gas Vent On The Right-Hand Side Of The Vehicle

    Appliances 9.4.1 Models with waste gas vent on the right-hand side of the vehicle If the awning is put up and the boiler is running in gas operation, exhaust  gases from the boiler can escape into the awning area. Danger of suffo- cation! Make sure the area is sufficiently ventilated.

  • Page 105: Truma Boiler (Special Equipment)

    Appliances Fig. 124 Drain cock for hot water source Filling the hot water source Connect the vehicle to the external 230 V power supply and switch on the  with water: 230 V automatic circuit breaker. Switch off the operating switch (Fig. 123). Indicator lamp (Fig. 123,1) in the ...
  • Page 106 Appliances Gas operation The boiler is operated exclusively with gas. 1 Temperature control knob 2 Red indicator lamp "Fault" 3 Rotary switch 4 Off 5 On Fig. 125 Operating unit for Truma boiler (gas operation) Switching on: Remove cap from waste gas vent. ...

  • Page 107: Alde Boiler (Partially Special Equipment)

    Appliances Switching off: Set the flip switch (Fig. 126,1) to " ". The indicator lamp on the switch goes  off. Combined operation The water is heated more quickly in the boiler if gas operation and 230 V elec- trical operation are switched on simultaneously. Further information can be obtained in the manufacturer's instruction ...

  • Page 108: Cooker

    Appliances Fig. 128 Drain cock Filling the boiler with water: Close the drain cock(s). Position the rocking lever (Fig. 128,1) horizontally.  Switch on 12 V power supply on the panel.  Set all the water taps to "Hot" and open them. The water pump is turned ...
  • Page 109 Appliances If there is a flame protection, always put it up when using the gas cooker.  Depending on the model, the gas cooker lid is held closed by a spring.  When closing there is danger of getting injured! Do not use the glass gas cooker lid as a hob.

  • Page 110: Gas Oven (Dometic) (Special Equipment)

    Appliances 9.5.2 Gas oven (Dometic) (special equipment) Keep the ventilation openings on the gas oven open at all times.  There must be no flammable objects near the gas oven when it is being  lit. If ignition has not taken place, repeat the entire procedure. If necessary, ...
  • Page 111 Appliances Never leave the microwave oven unattended when it is in operation.  If there is smoke, keep the microwave oven closed, switch it off and  interrupt the power supply. Operate the microwave oven only with the rotary plate and the rotary cross ...

  • Page 112: Extractor Hood (Partially Special Equipment)

    Appliances 9.5.4 Extractor hood (partially special equipment) Fig. 132 Extractor hood The cooking area is equipped with an extractor hood. The powerful fan blows the cooking steam directly outside. To switch on the extractor hood, press the right flip switch (Fig. 132,2). Use the left flip switch (Fig.

  • Page 113: Refrigerator Ventilation Grill

    Appliances 9.6.1 Refrigerator ventilation grill Fig. 133 Refrigerator ventilation grill (with sliding trap) Removal: Push sliding trap (Fig. 133,1) upward.  Remove refrigerator ventilation grill.  Fig. 134 Refrigerator ventilation grill (with screw) Removal: Turn screw (Fig. 134,1) one quarter turn using a coin. ...
  • Page 114 Appliances 1 Energy selector switch 2 "230 V" operating indicator 3 "GAS" operating indicator 4 "12 V" operating indicator 5 Control knob for setting the tempera- ture Fig. 135 Operating controls for the refrigerator (Dometic 7 series) Switching on: Open the regulator tap on the gas bottle and the gas isolator tap "Refriger- ...

  • Page 115: Operation (Dometic 7 Series With Frame Heater)

    Appliances Further information can be obtained from the separate instruction manual  "Refrigerator". 9.6.3 Operation (Dometic 7 series with frame heater) Volume Model RM 7651: 150 l (arched door) Operating modes The refrigerator has 2 operating modes: Gas operation  Electrical operation (230 V AC or 12 V DC) ...

  • Page 116: Operation (Dometic 8 Series With Manual Power Selection Mes)

    Appliances Electrical operation Close the gas isolator tap "Refrigerator" when the refrigerator is operated  electrically. The refrigerator can be operated with the following voltages: 230 V AC  12 V DC  Switching the 230 V Set energy selector switch (Fig. 136,3) to "230 V". The "230 V" operating ...
  • Page 117 Appliances Select only one energy source.  The refrigerator always requires a 12 V control voltage, regardless of which  type of energy it is using. The control voltage is present as soon as the transformer/rectifier is switched on. Therefore the closed circuit current always flows even if the refrigerator is switched off.

  • Page 118: Refrigerator Door Locking Mechanism

    Appliances The refrigerator can be operated with the following voltages: 230 V AC  12 V DC  Switching the 230 V Press the on/off switch/energy selector switch (Fig. 137,1) down for 2 sec-  operation on: onds in order to switch on the appliance. The LED of the operating mode chosen most recently lights up.
  • Page 119 Appliances Dometic 7 series Fig. 138 Locking of the refrigerator door Fig. 139 Refrigerator door in ventilation (Dometic 7 series) position (Dometic 7 series) Opening: Push the lock (Fig. 138,1) to the left " ".  Use recessed grip to open refrigerator door. ...
  • Page 120 Appliances Locking in the ventilation Slightly open refrigerator door/freezer compartment door.  position: Push the lock completely to the right. The door latch (Fig. 141,1) keeps the  refrigerator door/freezer compartment door in a fixed position. The refriger- ator door/freezer compartment door will then stay slightly open (Fig. 141). Dometic 8 series Fig.

  • Page 121: Sanitary Fittings

    Sanitary fittings Chapter overview 10Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the car- avan. The instructions address the following topics: water tank  waste water tank  complete water system  toilet compartment  toilet  10.1 Water supply, general Fill water tank from supply systems that have been verified to provide...

  • Page 122: Water Tank

    Sanitary fittings 10.2 Water tank When filling the water tank, observe the maximum permissible gross  weight of the vehicle. Luggage must be reduced accordingly when the water tank is full. 10.2.1 Water tank 22 l with external flap (special equipment) The water tank is mobile or portable.

  • Page 123: Water Tank 40 L

    Sanitary fittings 10.2.2 Water tank 40 l Fig. 147 Drinking water filler neck Fig. 148 Drinking water filler neck (alter- native) The drinking water filler neck is on the right or left side of the vehicle, depending on the model. The drinking water filler neck is labelled by the word "WASSER"...

  • Page 124: Waste Water Tank (Special Equipment)

    Sanitary fittings 10.3 Waste water tank (special equipment) Before commencing the journey, empty the waste water tank.  If there is any risk of frost, empty the waste water tank.  Never pour boiling water directly into the sink outlet. Boiling water could ...

  • Page 125: Emptying The Water System

    Sanitary fittings Fig. 152 Drain cock (with rocking lever) Fig. 153 Drain cock (with twist cap) Position the vehicle horizontally.  Connect the 230 V power supply and switch on the 230 V automatic circuit  breaker. If the vehicle is equipped with a self-sufficiency package with bat- tery, it is not necessary to connect it to a 230 V power supply.

  • Page 126: Toilet Compartment

    Sanitary fittings To empty and ventilate the water system, proceed as follows. Frost damage and deposits are avoided in this way: Position the vehicle horizontally.  Switch off the 230 V power supply on the 230 V automatic circuit breaker. ...

  • Page 127: Swivel Toilet (Thetford C-200)

    Sanitary fittings Further information can be obtained in the manufacturer's instruction  manual. Only empty the sewage tank (cassette) at disposal stations, at camping  sites or caravan sites, that are especially provided for this purpose. Depending on the design, the toilet is flushed either directly via the vehicle's water system, or via a separate water tank.
  • Page 128 Sanitary fittings Fig. 156 Turning drainage neck Place the Thetford cassette upright.  Turn the drainage neck upwards.  Remove the cap of the drainage neck.  Never put the sanitary liquid directly in the toilet bowl.  Fig. 157 Filling with sanitary liquid Fill the Thetford cassette with the specified quantity of sanitary liquid.
  • Page 129 Sanitary fittings Fig. 158 Inserting the Thetford cassette Push the Thetford cassette back to its original position.  Fig. 159 Thetford cassette secured Ensure that the Thetford cassette is secured by the retaining clip.  Lock the flap for the Thetford cassette. ...
  • Page 130 Sanitary fittings Fig. 161 Pre-flush Fill the toilet bowl with some water. Press the flush button. Flushing con-  tinues as long as the button is pressed. Use the toilet.  C-200 S cassette With the C-200 S cassette, proceed as follows to flush the toilet: Fig.
  • Page 131 Sanitary fittings C-200 E cassette With the C-200 E cassette, proceed as follows to flush the toilet: Fig. 164 Opening the sliding trap Open the sliding trap. To do this, press the left side of the sliding trap  button. Fig.
  • Page 132 Sanitary fittings Fig. 167 Carrying the Thetford cassette Take the Thetford cassette to a proper disposal area. As you do this, point  the drainage neck upwards. Fig. 168 Emptying the Thetford cas- sette Turn the drainage neck upwards.  Remove the cap of the drainage neck.

  • Page 133: Toilet With Fixed Seat (Thetford C-402)

    Sanitary fittings 10.7.2 Toilet with fixed seat (Thetford C-402) The Thetford toilet of some models is equipped with its own water tank. Fig. 170 Fresh water filler neck, swung Filling the water tank: Open the flap for the Thetford cassette. ...
  • Page 134 Sanitary fittings Fig. 173 Pulling the retaining clip Preparing toilet: Open the flap for the Thetford cassette and pull the retaining clip  upwards to remove the Thetford cassette. Fig. 174 Removing the Thetford cas- sette Pull out the Thetford cassette as far as it can go. ...
  • Page 135 Sanitary fittings Fig. 176 Filling with sanitary liquid Fill the Thetford cassette with the specified quantity of sanitary liquid.  Then add enough water to completely cover the bottom of the Thetford cas-  sette. Close drainage neck with the cap. ...
  • Page 136 Sanitary fittings Fig. 179 Pre-flush Using the toilet: Fill the toilet bowl with some water. Press the flush button. Flushing con-  tinues as long as the button is pressed. Use the toilet.  Fig. 180 Operating the sliding trap Open the sliding trap.
  • Page 137 Sanitary fittings Fig. 182 Removing the Thetford cas- sette Emptying the Thetford Open the flap for the Thetford cassette and pull the retaining clip  cassette: upwards to remove the Thetford cassette. Pull out the Thetford cassette as far as it can go. ...
  • Page 138 Sanitary fittings Activate the aeration knob with your thumb. The Thetford cassette empties.  Rinse the Thetford cassette thoroughly with fresh water.  Close drainage neck with the cap.  Return the drainage neck to its original position.  Fig. 185 Inserting the Thetford cassette Prepare the Thetford toilet for use.
  • Page 139 Sanitary fittings Remove the screw cap from the fresh water filler neck.  Turn the fresh water filler neck in an anticlockwise direction until the  residual water flows out. Turn the fresh water filler neck back in a clockwise direction. ...
  • Page 140 Sanitary fittings Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 141: Care

    Care Chapter overview 11Care This chapter contains instructions regarding the care of the vehicle. The instructions address the following topics: exterior of the vehicle  interior  water system  extractor hood  air conditioning unit  winter operation  At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time.

  • Page 142: Washing The Vehicle

    Care 11.1.3 Washing the vehicle Never clean the vehicle in the car wash. Water can enter the refrigerator  grills, the waste gas vents, the ventilation of the extractor hoods or the forced ventilations. The vehicle could be damaged. Wash the vehicle only on a washing site intended for this purpose. ...

  • Page 143: Underbody

    Care Snow (e.g. by standing too long in snow)  Defective ventilation (e.g. by covering with aprons in the floor area)  To avoid formation of white rust or to remove any existing white rust, we rec- ommend the following method: After driving in winter, rinse out the hot galvanized surfaces with clean ...

  • Page 144: Water System

    Care Surface and knobs of furniture, lamps and synthetic parts in the toilet and  living area should be cleaned with water and a wool cloth. A mild cleanser may be added to the water. If required, use furniture polish for the painted surfaces.

  • Page 145: Disinfecting The Water System

    Care Collect any emerging mixture of water and cleaning agent for correct dis-  posal. Empty the water system.  Close all drain holes and drain cocks.  Fill mixture of water and cleaning agent into the water tank. Observe the ...

  • Page 146: Extractor Hood

    Care Leave the water taps open until the mixture of water and disinfectant has  reached the drain. Close all water taps.  Flush the toilet several times.  Allow the disinfectant to act in accordance with the manufacturer's instruc- ...

  • Page 147: Winter Care

    Care Cleaning the filter: Wash the filter with warm water and some washing-up liquid.  Allow the filter to dry thoroughly before reassembly.  Cleaning the ventilation grill: Use a brush to remove coarse dirt or deposits from the external ventilation ...

  • Page 148: At The End Of The Winter Season

    Care 11.6.3 At the end of the winter season Thoroughly clean the underbody. When this is done, corrosion-inducing  anti-freeze agents (salts, alkaline residues) are removed. Clean the exterior and use regular car wax to protect metal surfaces.  Remove vent extension. ...

  • Page 149: Winter Lay-Up

    Care Activities Done Gas system Close regulator tap on the gas bottle Close all gas isolator taps Always remove gas bottles from the gas bottle compartment, even if they are empty Electrical system Spray the contacts on the thirteen-pin connector with contact spray Fully charge the living area battery (if there is one) ...

  • Page 150: Starting Up The Vehicle After A Temporary Lay-Up Or After Lay-Up Over Winter

    Care Activities Done Complete vehicle Clean the awning area and store in a dry place Arrange the tarpaulins in such a way that the ventilation openings are not covered, or use porous tarpaulins 11.7.3 Starting up the vehicle after a temporary lay-up or after lay- up over winter Go through the following checklist before start-up: Activities...

  • Page 151: Maintenance

    Maintenance Chapter overview 12Maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle. The maintenance instructions address the following topics: caravan couplings  hitching device Easy-Pull  braking system  doors  Alde hot-water heater  replacing light bulbs ...

  • Page 152: Aks 1300

    Maintenance 12.3.2 AKS 1300 Fig. 189 Friction control Fig. 190 Friction control Checking the stabilising Prerequisite: Connection to AKS 1300, ball diameter 50 mm device (on the side of the friction pads) Turn the handwheel (Fig. 189,1), until it can be heard and felt that the ...

  • Page 153: Ws 3000 D

    Maintenance Resetting the friction pads is not required.  12.3.4 WS 3000 D Fig. 193 Stabilising handle Fig. 194 Wear indicator Checking the stabilising Prerequisite: Connection to WS 3000, ball diameter 50 mm device (on the side of the friction pads) Activate the stabilising mechanism.

  • Page 154: Doors

    Maintenance 12.6 Doors To maintain gliding capability between springs and hinges, grease the conver- sion door hinges occasionally. We recommend either Molykote PG 65 or Vaseline as lubricants.  12.7 Alde hot-water heater Check the level of the heating fluid regularly on the compensator reservoir. ...

  • Page 155: Bleeding The Heating System

    Maintenance Check anti-freeze with an anti-freeze hydrometer. The frost protection con-  tent must be 40 % or correspond to a frost protection of -25 °C. Fill water frost protection mixture slowly into the compensator reservoir.  The optimum fluid level is reached when the fluid in the compensator res- ...

  • Page 156: Front Lights

    Maintenance Types of bulbs Different types of bulbs are used in the vehicle. Below, we have described how to change the different types of bulbs. Fig. 197 Types of bulbs Pos. in Fixture type/bulb Changing Fig. 197 type Plug-in fixture To remove, pull out the bulb To mount, push the bulb into the socket with gentle pressure...

  • Page 157: Rear Lights

    Maintenance 12.8.2 Rear lights 1 Rear light 2 Brake light 3 Direction indicator 4 Reverse light 5 Fog tail light 6 Licence plate light 7 Brake light Fig. 199 Rear lights Undo five housing screws.  Remove housing.  Remove bulb. ...

  • Page 158: Types Of Bulbs For Exterior Lighting

    Maintenance 12.8.4 Types of bulbs for exterior lighting Item Exterior lighting Type of bulb Front Front light Rear Rear light Ba15s 12 V 5 W Brake light Ba15s 12 V 21 W Direction indicator Ba15s 12 V 21 W orange Reverse light Ba15s 12 V 21 W Fog tail light...

  • Page 159: Ceiling Lamp

    Maintenance 12.9.1 Ceiling lamp Fig. 201 Ceiling lamp The ceiling lamp has LEDs. Changing bulbs: Press the two ends (Fig. 201,2) of the spring ring (Fig. 201,1) together and  remove. Remove the housing (Fig. 201,3) with LED from the lamp. ...

  • Page 160: Recessed Halogen Light

    Maintenance 12.9.3 Recessed halogen light Fig. 203 Recessed halogen light Fig. 204 Changing the halogen bulb Halogen bulb 12 V/10 W The recessed halogen light (Fig. 203,1) is installed flush with the panel. Changing bulbs: Use a screwdriver to remove the inner cover ring (Fig. 204,1) from the ...

  • Page 161: Spare Parts

    Maintenance 12.10 Spare parts Every alteration of the original condition of the vehicle can alter road  behaviour and jeopardize road safety. The special equipment and original spare parts recommended by us  have been specially developed and supplied for your vehicle. These products are available at the authorised dealer or service centre.

  • Page 162: Warning And Information Stickers

    Maintenance Do not remove the vehicle identification plate. The vehicle identification plate: Identifies the vehicle  Helps with the procurement of spare parts  Together with the vehicle documents identifies the vehicle owner  Always include the chassis number with all inquiries for the customer ...

  • Page 163: Wheels And Tyres

    Wheels and tyres Chapter overview 13Wheels and tyres This chapter contains instructions regarding the tyres of the vehicle. The instructions address the following topics: tyre selection  handling of tyres  changing wheels  spare wheel support  At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle.

  • Page 164: Tyre Selection

    Wheels and tyres Fig. 207 Tighten the wheel nuts or wheel bolts cross-wise Check regularly that the wheel nuts or wheel bolts are firmly seated. Re-  tighten the wheel nuts or wheel bolts of a changed wheel cross-wise (Fig. 207) after 50 km (30 miles). See section 13.5.2 for tightening torque.

  • Page 165: Tyre Specifications

    Wheels and tyres 13.3 Tyre specifications Description Explanation 215/70 R 15C 109/107 Q Tyre width in mm Height-to-width proportion in percent Tyre design (R = radial) Rim diameter in inches Commercial (transporter) Load index code for single tyres Load index code for twin tyres Speed index (Q = 160 km/h) 13.4 Handling of tyres...

  • Page 166: Tightening Torque

    Wheels and tyres No persons may be in the vehicle while it is is raised.  Whilst the vehicle is in a jacked up position, persons must not lie down  under it. Do not damage the thread of the thread bolts when changing the wheel. ...
  • Page 167 Wheels and tyres A special vehicle jack from AL-KO with holder pockets is available as spe-  cial equipment. These holder pockets are mounted on to the frame. The AL-KO jack has a bearing capacity of 800 kg.  You should have a useable spare wheel available at all times. For this ...

  • Page 168: Changing A Wheel At Alloy Wheel Rims

    Wheels and tyres AL-KO vehicle jack:  Hold on to the AL-KO vehicle jack with one hand and with the other turn the hand crank (Fig. 212,4) in a clockwise direction until the footplate (Fig. 212,3) is touching the ground and is in a level position. Turn the wheel bolts several times to loosen them, but do not remove them! ...

  • Page 169: Spare Wheel Support Under The Vehicle (Special Equipment)

    Wheels and tyres Removing the spare wheel: Undo bolt (Fig. 213,1).  Remove the spare wheel (Fig. 213,2).  13.6.2 Spare wheel support under the vehicle (special equipment) Fig. 214 Spare wheel support Fig. 215 Spare wheel fixture The spare wheel support is located under the vehicle near the axle. Removing the spare wheel: Unhook the safety chain (Fig.
  • Page 170 Wheels and tyres 1 Correct tyre pressure 2 Tyre pressure too low 3 Tyre pressure too high Fig. 216 Contact surface of the tyre The information on pressure levels is valid for cold tyres and loaded vehi-  cles. Pressure in hot tyres must be 0.3 bar higher than in cold tyres. Recheck the ...
  • Page 171 Wheels and tyres Tyres Maximum per- Maximum per- Tyre pressure missible gross missible gross (bar) weight mono weight tandem axle (kg) axle (kg) 195 R 14 C LI106 Up to 1,100 3.25 1,200 3.25 1,300 3.50 1,400 3.50 1,500 4.50 1,600 2,800 4.50...
  • Page 172 Wheels and tyres Tyres Maximum per- Maximum per- Tyre pressure missible gross missible gross (bar) weight mono weight tandem axle (kg) axle (kg) 215/70 R 15 C LI109 Up to 1,100 3.00 1,200 3.25 1,300 3.50 1,400 3.50 1,500 4.00 1,600 2,800 4.25...

  • Page 173: Troubleshooting

    Troubleshooting Chapter overview 14Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies. The instructions address the following topics: chassis  braking system  caravan control system  electrical system ...

  • Page 174: Caravan Control System

    Troubleshooting 14.3 Caravan control system 14.3.1 Caravan control system (ATC) Fault Cause Remedy Control LED flashes ATC active Drive approx. 30 m with green (possible to contin- the trailor at a minimum Self test not yet complete ue journey) 10 km/h. If the control LED continues to flash, contact customer servic- Control LED lights up red...

  • Page 175: Caravan Control System (Idc)

    Troubleshooting 14.3.2 Caravan control system (IDC) Fault Cause Remedy Control LED flashes Brake heated up (limited Allow the brake to cool green (slowly) braking effect) down Control LED lights up Standby mode Automatic reactivation green (briefly, every during driving 5 seconds) Control LED flashes red Error in the central unit Disconnect and then re-...

  • Page 176: Gas System

    Troubleshooting Fault Cause Remedy 12 V power supply in the 230 V automatic circuit Switch on 230 V auto- living area does not work breaker switched off matic circuit breaker Fuse on the power sup- Replace fuse ply unit is defective Power supply unit is de- Contact customer service fective...

  • Page 177: Cooker

    Troubleshooting Fault Cause Remedy No gas Gas bottle is empty Change gas bottle Gas isolator tap closed Open the gas isolator tap Regulator tap on the gas Open regulator tap on bottle is closed the gas bottle External temperature is Wait for higher external too low (-42 °C for pro- temperatures...

  • Page 178: Trumatic S Hot-Air Heater

    Troubleshooting 14.7.1 Trumatic S hot-air heater Fault Cause Remedy For heater with automatic Battery on the automatic Changing the battery on ignition: Heater does not ignition empty the automatic ignition ignite 14.7.2 Alde heater/boiler Fault Cause Remedy Heating does not ignite Lack of gas Open regulator tap and with gas operation...

  • Page 179: Truma Hot Water Source

    Troubleshooting Fault Cause Remedy Electrical operation Boiler is connected to Operating switch is Switch on the operating power supply but is not switched off switch, the indicator lamp heated on the switch must light Operating switch defec- Contact customer service tive 230 V automatic circuit Switch on the 230 V au-...

  • Page 180: Dometic 8 Series

    Troubleshooting Fault Cause Remedy Refrigerator does not Contacts on the plug Clean contacts and spray switch on when operating and/or in the socket have with contact spray in 12 V mode oxidised and/or are con- taminated Short circuit caused by Open plug and/or sock- water in the plug and/or et, dry out, and spray...

  • Page 181: Air Conditioning Unit

    Troubleshooting Fault Cause Remedy Lack of gas Open regulator tap and LED " " flashes gas isolator tap Connect a full gas bottle Cobwebs or burnt resi- Remove the ventilation due in the burning cham- grill on the outside of the vehicle and clean the burning chamber LEDs for display of the...

  • Page 182: Telair

    Troubleshooting 14.9.2 Telair Fault Cause Remedy Air conditioning unit does No 230 V power supply Connect 230 V power not start up supply 230 V automatic circuit Switch on the 230 V au- breaker has triggered tomatic circuit breaker Remote control batteries Change batteries empty (2 x AAA)

  • Page 183: Body

    Troubleshooting Fault Cause Remedy Milkiness of the water Tank filled with dirty wa- Clean water tank me- chanically and chemical- ly; then disinfect and rinse copiously with drinking water Residues in the water Clean water system me- tank or water system chanically and chemical- ly;...
  • Page 184 Troubleshooting Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 185: Special Equipment

    Special equipment 15.1 Weight details for special equipment 15Special equipment The use of accessories, parts and fittings not supplied by us may cause  damage to the vehicle and jeopardize road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product.
  • Page 186 Special equipment Item designation Surplus weight (kg) Floor warming unit Gas bottle (11 kg) made of aluminium Gas bottle switching facility, automatic Gas alarm system Weight increase 5-10 Smooth plate Holder for flat screen Heater S 5002 Insect screen, door (full height) Children's bunk bed with 3 levels Air conditioning unit (Dometic) Air conditioning unit (Telair)

  • Page 187: Technical Data

    Technical data 16.1 Table of linear measures 16Technical data 460 TL 5790 5200 2320 7120 2540 9270 465 TS 5890 5300 2320 7200 2540 9870 490 TS 6090 5500 2320 7410 2540 10070 510 TS 5890 5300 2520 7260 2540 9870 535 TL 6170...
  • Page 188 Technical data Belcanto/Trecento - 10/11 - Ausgabe 07/10 - 1976844 - BUE-0042-06EN...

  • Page 189: Helpful Notes

    Helpful notes Chapter overview 17Helpful notes This chapter contains helpful tips for the journey. The instructions address the following topics: road assistance in European countries  traffic rules in European countries  gas supply in European countries  toll regulations in European countries ...
  • Page 190 Helpful notes Country Emergen- Breakdown service cy services Police Greece ELPA 104 00 171/112 Great Britain AA (08 00) 0 28 90 18 Ireland AA Dublin 18 00 66 77 88 999/112 999/112 Iceland F.I.B 5 11 21 12 Italy ACI 8 00 11 68 00 118/112 Croatia...

  • Page 191: Speed Limits

    Helpful notes Country Emergen- Breakdown service cy services Police Serbia AMSS 987 Slovakia SATC 1 81 24 Slovenia AMZS (1) 9 87/ 00386 1 5 30 53 53 Spain RACE 9 15 93 33 33 061/112 Czech Republic UAMK CR 12 30 Turkey TTOK (02 12) 2 82 81 40 155/112...
  • Page 192 Helpful notes Country In built-up Outside built-up Motorway areas areas Great Britain 80/96 Ireland Iceland – Italy Croatia Latvia Lithuania Luxembourg Macedonia 40/60 Montenegro Netherlands Norway Austria Poland 70/80 Portugal 70/80 Romania 70/80 Russia Sweden Switzerland Serbia Slovakia Slovenia Spain 70/80 Czech Republic Turkey...

  • Page 193: Driving With Low Beam In European Countries

    Helpful notes Trailers with no brakes and a current gross weight exceeding 300 kg With trailer of over 750 kg (max. perm. gross weight of 3.5 t), the following applies: On highways 80 km/h, on motorways 100 km/h. For towing vehicles over 3.5 t perm.
  • Page 194 Helpful notes Country Sleeping on Sleeping on Comments roads and privately fields owned lands Italy Staying overnight for one night at car parks and service stations is allowed. Observe the local regulations. Parking and staying overnight on free areas is pro- hibited Croatia Luxembourg...

  • Page 195: Gas Supply In European Countries

    Helpful notes Country Sleeping on Sleeping on Comments roads and privately fields owned lands Turkey Ukraine Hungary Staying overnight on privately owned land is permitted only with police certification Specifications without guarantee 17.6 Gas supply in European countries In Europe, there are several different connection systems for gas bottles. It ...

  • Page 196: Tips For Winter Campers

    Helpful notes Before commencing the journey, close and lock all windows, doors and  skylights. During high season do not spend the night at highway rest stops or parking  areas located along typical vacation routes. Several vehicles on one site at the same time do not necessarily decrease ...
  • Page 197 Helpful notes Do not leave checking of documents (e.g. vehicle papers and information)  as well as checking the condition of the vehicle until just before com- mencing the trip. Planning and checking documents well in advance will save unnecessary trouble. Object Object Object...
  • Page 198 Helpful notes Object Object Object Vehicle/tools Waste water con- Fabric tape Screwdriver tainer Adapter socket Watering can for Current-measuring drinking water instrument CEE adapter Cable reel Step Wire V-belt Wheel chocks Spare wheel Glue First-aid kit Spare lamps Universal pliers Vehicle jack Spare fuses Compressor...

  • Page 199: Inspection Plan

    Inspection plan 18Inspection plan Pos. Component Activity Interval Jockey wheel Lubricate, check wheel Annually rims for damage, visu- al check of the tyres, check threaded spin- dle and crank Corner steadies Lubrication Annually Joints, hinges and levers on the Lubrication Annually chassis Underbody...
  • Page 200 Inspection plan Delivery Pos. 1-13 Stamp of the Bürstner dealer Date Signature 1st year Pos. 1-13 2nd year Pos. 1-21 Stamp of the Bürstner dealer Stamp of the Bürstner dealer Date Signature Date Signature 3rd year Pos. 1-13 4th year Pos.
  • Page 201 Index 12 V fuses ......84 Appliances ......91 For the refrigerator .
  • Page 202 Index Halogen spotlight ....160 Washing ......142 Interior lighting .
  • Page 203 Index Corner steadies ......35 Extractor hood ......112 Cranking down .
  • Page 204 Index Heater automatic ignition, changing the battery ....... . .94 Gas alarm system .
  • Page 205 Index Light metal wheel rims see alloy wheel Heating system, bleeding ... . . 155 rims ....... . . 168 Maintenance work .
  • Page 206 Index Gas operation, switching on ..... . . 114 Net curtains, cleaning ....144 Operating modes .
  • Page 207 Index Seating groups, sleeping conversion ..64 Shower ......126 Table of linear measures .
  • Page 208 Index Extractor hood ..... . 176 Waste gas vent, cap .....105 Furniture flaps .

Table of Contents

Save PDF