Do you have a question about the I 2012 and is the answer not in the manual?
Questions and answers
Antonio Martins
March 10, 2025
Como ligar relógio e temporizador
1 comments:
Mr. Anderson
May 14, 2025
To set the clock on a Burstner I 2012:
1. Switch on the digital clock display by pressing the upper part of the rocker switch (Fig.130,11). 2. Use a thin device, such as a biro, to: - Press into the hour display opening (Fig.130,10) until the correct hour is shown. - Press into the minute display opening (Fig.130,9) until the correct minutes are shown.
Note: - The clock continues running even if the display is off. - If the living area battery is disconnected, the clock resets to 00:00 and must be set again.
Page 1
Instruction manual Dear Reader ... Instruction manual We would like to congratulate you on the purchase of your new motorhome. You have selected a top-quality vehicle which will afford you many years of enjoyment. To enable you to always use and operate your motorhome properly and easily, your Bürstner dealer will first provide you detailed instructions for all important functions when you take delivery.
Contents Introduction Pilot seats for the driver's and ....9 front passenger's seats ... . 40 General .
Page 4
Contents 6.1.7 Window of conversion door 6.12 Divan adjustment mechanism (Hartal Premium) (partially special equipment) ..87 (partially special equipment) ..60 6.13 Beds ......88 6.1.8 Folding insect screen on the 6.13.1...
Page 5
Contents 8.7.1 V/tank gauge for battery voltage Boiler ......163 and water or waste water levels ..120 9.4.1 Models with waste gas vent on 8.7.2...
Page 6
Contents 11.1.6 Waste water tank ....205 13.3 Tyre specifications ....235 11.1.7 Entrance step.
Page 7
Contents 17.8 Tips on staying overnight safely during travel ....274 17.9 Tips for winter campers... 275 17.10 Travel checklists .
Introduction Please read this instruction manual completely before 1Introduction using the vehicle for the first time! Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. The non-observance of this symbol can lead to personal injury. The non-observance of this symbol can lead to damage being caused to, or inside the vehicle.
Introduction Only use the vehicle in a technically impeccable condition. Follow the instruc- tions in the instruction manual. Malfunctions which impair the safety of persons or the vehicle should be immediately remedied by qualified personnel. To avoid further damages, observe the duty to avert, minimize or mitigate loss for the user during faults. Have the vehicle's braking and gas systems inspected and repaired by an authorised specialist workshop only.
Safety Chapter overview 2Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: fire prevention and what to do in case of fire general care of the vehicle road safety of the vehicle towing gas system of the vehicle...
Safety All windows and doors which meet the following requirements are considered as emergency exits: Open to the outside or can be shifted in horizontal direction Opening angle at least 70° Minimum diameter of clearance = 450 mm Maximum distance from the vehicle floor = 950 mm General The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances.
Page 13
Safety Before commencing the journey and after short interruptions of the journey, ensure that the entrance step is completely retracted. Before commencing the journey, secure the hinged pull-down bed. Before commencing the journey, open and secure the shades on the windscreen and on the driver's and front passenger's windows.
Safety Before commencing the journey, remove the external supports and retract the corner steadies or steady legs, which are fitted to the vehicle. Before commencing the journey, put the antenna in park position. During the initial journey and each time after changing a wheel, re-tighten the wheel bolts/wheel nuts after 50 km (30 miles).
Safety Do not use the gas cooker or gas oven for heating purposes. If there are several gas devices, each gas device must have its own gas isolator tap. If individual gas devices are not in use, close the respective gas isolator tap.
Safety Only use special gas pressure regulators with a safety valve designed for vehicle use. Other gas pressure regulators are not permitted and cannot meet the demanding requirements. Use the gas pressure regulator defroster if the temperature falls below 5 °C. Use only 11 kg or 5 kg gas bottles.
Before the journey Chapter overview 3Before the journey This chapter contains important information which has to be noted before com- mencing your journey or carrying out any tasks before the journey. The instructions address the following topics: keys registration calculating the payload correct loading of the vehicle and bike rack load rack towing...
Before the journey Payload Overloading the vehicle and wrong tyre pressure can cause tyres to burst. You can lose control of the vehicle. Only the maximum permissible gross weight and the mass in a ready-to- drive condition, not the actual weight of the vehicle, is stated in the vehicle documents.
Page 19
Before the journey Mass in ready-to-drive The mass in ready-to-drive condition is the weight of the ready-to-drive condition standard vehicle. The mass in ready-to-drive condition is made up as follows: Unladen weight (mass of the empty vehicle) with factory-installed standard equipment Driver's weight Basic equipment weight...
Before the journey Additional equipment Additional equipment includes accessories and special equipment. Examples of additional equipment include: Caravan coupling Roof rail Awning Bike or motorcycle rack Satellite unit Microwave oven Chapter 15 lists the weights of the various items of special equipment; they may also be obtained from the manufacturer.
Before the journey The payload (see section 3.3.1) is the difference in weight between Maximum permissible gross weight in a laden condition and Vehicle mass complete in a ready-to-drive condition. Mass in kg to be Calculation calculated Example for calculating Maximum permissible gross weight ac- 3500 cording to vehicle documents...
Page 22
Before the journey Distribute the load evenly on both axles. In doing so, observe the axle loads specified in the vehicle documents. Observe the permissible load- carrying capacity of the tyres (see chapter 13). Heavy loads behind the rear axle can reduce the load on the front axle due to the leverage effect ( ).
Before the journey If the calculated value exceeds the permissible axle load, the load must be dis- tributed in a different way. If the load on the front axle is too low, the grip of the tyres on the road is reduced (traction).
Before the journey Fig. 1 Rear ladder Climbing on to the roof (rear Hook the lower part of the ladder (Fig. 1,1) in the part of the ladder ladder): (Fig. 1,2) which is fastened to the rear, and place it on the ground. Carefully climb the ladder.
Before the journey 3.3.6 Double floor Observe the permissible axle loads and maximum permissible gross weight when loading the double floor. Distribute the load evenly. Excessive spot loads can lead to damages of the floor covering. 3.3.7 Extendable storage compartment The maximum permitted extendable storage compartment load is 40 kg.
Before the journey Loading the bike rack with When loading the bike rack, observe the centre of gravity. The centre of gravity bicycles of the bicycles must be as close as possible to the rear wall of the vehicle. The bike rack should always be loaded from the inside to the outside.
Before the journey Always make sure to store the load roadworthy and secure it against falling. The load may not jut out beyond the maximum width of the vehicle. The lighting and the official licence plate on the load rack may not be covered by the load.
Page 28
Before the journey Always make sure to store the load roadworthy and secure it against falling. The load may not jut out beyond the maximum width of the vehicle. The lighting and the official licence plate on the load rack may not be covered by the load.
Before the journey Towing Care is to be taken when connecting and detaching a trailer. Risk of acci- dent and injury! No persons are to be between the towing vehicle and the trailer during positioning for connecting and detaching. Observe the permissible nose weight and rear axle load of the towing vehicle.
Before the journey Entrance step (partially special equipment) Before commencing the journey and after short interruptions of the journey, ensure that the entrance step is completely retracted. Do not stand in the direct range of the entrance step while it is being retracted or extended.
Before the journey Fig. 10 Indicator lamp When the ignition is switched on and the entrance step is extended, an indi- cator lamp (Fig. 10,1) is illuminated on the dashboard. Television (special equipment) Before commencing the journey, remove the television from the support and store it securely.
Before the journey Securing add-on parts In the event of an accident or emergency braking, loose add-on parts could injure the occupants of the vehicle. Before setting off, secure loose add-on parts in the holders provided or stow them in a secure place inside the vehicle.
Before the journey 3.11 Road safety Check tyre pressure before a journey or every 2 weeks. Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst. You can lose control of the vehicle. Before commencing the journey, work through the checklist: Checks Checked Base vehicle...
Page 34
Before the journey Checks Checked Pull-down bed secured Children's seats mounted to seats with three-point safety belts Swivel seat locking device for driver's seat and front passen- ger's seat locked Shades in the driver's cabin opened and secured Gas system Gas bottles firmly fixed in the gas bottle compartment so that they are unable to turn If the gas bottles are not connected to the gas tube, always...
During the journey Chapter overview 4During the journey This chapter contains instructions on how to drive the motorhome. The instructions address the following topics: the parking distance control reversing camera with LCD monitor driving speed brakes seat belts child restraint system seats and headrests seating arrangement electrical window winders...
During the journey If a reversing camera is installed in the vehicle, the camera is automatically switched on when driving in reverse gear. If the vehicle is equipped with the automatic transmission Comfort-Matic from Fiat, please note the following: The acoustic signal described in the instruction manual for Comfort-Matic is not active in our vehicles.
Page 37
During the journey When you switch on the ignition, the parking distance control runs a self- test. If a sensor is defective, this is indicated on the display by rapid flashing of the sensor position. The parking distance control continues to function, with the exception of the defective sensor.
During the journey Reversing camera (partially special equipment) Depending on the model, different monitor systems can be installed in the vehicle. The function of the reversing camera is the same way for all sys- tems. Fig. 14 Reversing camera (example) Fig.
During the journey Driving speed The vehicle is equipped with a powerful engine. This means there are sufficient reserves in difficult traffic situations. This high power enables a high maximum speed and requires above-average driving ability. The vehicle provides a large contact surface for wind. A sudden cross- wind can be especially dangerous.
During the journey After an accident, replace the seat belts. During the journey, do not tilt the backrest too far backwards. Otherwise the functionality of the seat belt is no longer guaranteed. 4.6.1 Fastening the seat belt correctly Do not twist the belt. The belt must be positioned smoothly against the body.
During the journey 4.8.1 Seats (Aguti) 1 Lengthways adjustment 2 Armrest adjustment 3 Rotating 4 Backrest adjustment Fig. 17 Driver's seat and front pas- senger's seat Rotating seats The seats can be rotated in any direction. The seats can only be locked in posi- tion in the direction of travel.
During the journey Push both armrests upward. Slide seat forward. Operate the release lever (Fig. 18,3). The latch is released. Rotate the seat. Moving seat in Adjust the driver's seat so that the driver can depress the pedals comfortably. lengthways direction Pull the bar (Fig.
During the journey 4.10 Seating arrangement During the journey, persons are only to sit on the permitted seats. The authorised number of seats is stipulated in the vehicle documents. During the journey sitting on the divans is not permitted. Seat belts must be worn by all passengers. Fig.
During the journey 4.12 External mirrors Fig. 24 External mirrors Depending on the model or equipment, the vehicle is equipped with two elec- trically adjustable and heated external mirrors (Fig. 24,1). The switch used to adjust the external mirrors is located on the driver's door or on the left of the dashboard.
During the journey Fig. 27 Roman shade Fig. 28 Lock for Roman shade Opening and closing: Grasp the handle (Fig. 27,1) of the Roman shade and slide to the left or the right. Securing: Push the handle (Fig. 28,1) onto the cap. The Roman shade is secured. 4.14 Bonnet When the bonnet is open, there is a risk of injury in the engine compart-...
During the journey 4.15 Washer nozzles Fig. 30 Washer nozzle The vehicle has washer nozzles with an adjustable angle of spray. Adjusting: Use a suitable screwdriver to turn the adjusting screw (Fig. 30,1) until you reach the desired position. 4.16 Filliing with washer fluid Fig.
During the journey 4.17 Filling up with diesel No appliance operated by a naked flame (e.g. heater or refrigerator) may be in operation when filling the tank, on ferries or in the garage. Danger of explosion! The cap for the fuel filler neck and for the drinking water filler neck are very similar.
Page 48
During the journey I-Modell - 11/12 - Ausgabe 09/11 - 2096165 - BUE-0056-05EN...
Pitching the motorhome Chapter overview 5Pitching the motorhome This chapter contains instructions on how to pitch the vehicle. The instructions address the following topics: handbrake entrance step ramps wheel chocks operation of the supports 230 V connection refrigerator aligning the antenna retracting and extending the awning Pitch the vehicle so that it is as horizontal as possible.
Pitching the motorhome Supports 5.5.1 General instructions Do not use the fitted supports as a vehicle jack. They supports are only for stabilising the parked vehicle to prevent the rear axle from bottoming out. When pitching the vehicle, ensure that the supports are evenly loaded. Before driving away, wind up the supports as far as they can go, fully retract and secure them.
Pitching the motorhome Push in the support foot extension (Fig. 34,5) and insert the splint (Fig. 34,4) in the drilled hole in the support foot extension. Rotate the hexagonal nut (Fig. 34,1) until the steady leg has swung upwards and the guide (Fig. 34,2) has reached the very end of the slot (Fig.
Pitching the motorhome 5.5.4 Electrical steady legs (AL-KO) (special equipment) Always observe the electrical steady legs when extending or retracting them. When extending or retracting the steady legs, ensure that no one is in the vehicle. Risk of injury due to unexpected rolling motion. Never extend the steady legs so far that the tyres of the vehicle are not in contact with the ground.
Pitching the motorhome Do not extend the steady leg to the end position without it being in contact with the ground. Extending: Press the push button for approx. 2 seconds until a brief sound is emitted. The steady legs control is now activated. Press and hold the preselection button for the steady leg side (Fig.
Pitching the motorhome Refrigerator If the refrigerator is set to 12 V operation, it will constantly consume cur- rent. Therefore, switch over to gas operation when the vehicle engine is not running, and the vehicle is not connected to the 230 V power supply. For units with an automatic power selection, the 12 V operation of the refriger- ator only functions in the automatic mode when the vehicle engine is running.
Pitching the motorhome The flat screen incorporates a digital receiver. The satellite unit is operated via remote control. Fig. 39 Remote control for television Switching on the satellite Switch on the television. unit: Press the key " " (Fig. 39,2) on the remote control for the television. The unit switches to search mode.
Pitching the motorhome The vehicle must be still during the satellite search. Do not walk through the vehicle. Satellite reception is only possible, when the antenna is positioned in direct line of sight of the chosen satellite and the view is not blocked in any way. Also read the manufacturer's instruction manual.
Living Chapter overview 6Living This chapter contains instructions about living in the vehicle. The instructions address the following topics: opening and closing the doors and flaps light switches light control adjusting the halogen spotlights positioning the television ventilation of the vehicle opening and closing the windows and blinds opening and closing the Roman shades in the driver's cabin opening and closing the skylights...
Living Locking: Insert the key into the locking cylinder (Fig. 41,1) and turn towards "Lock" (Fig. 41,2) until the door is locked. Return the key to the central position and remove it. 6.1.2 Driver's door, inside (partially special equipment) Fig. 42 Door lock of driver's door, inside Opening:...
Living 6.1.6 Conversion door, inside (Hartal Premium) (partially special equipment) Fig. 46 Door lock of conversion door, inside Opening: Pull on the handle (Fig. 46,2). The door lock is unlatched. Locking: Press the upper part of the handle (Fig. 46,2) in the direction of the recessed handle (Fig.
Living 6.1.8 Folding insect screen on the conversion door (partially special equipment) Open the insect screen completely before closing the conversion door. Fig. 48 Insect screen Closing: Pull out the insect screen completely by the bar (Fig. 48,1). Opening: Push the insect screen into its initial position by the bar (Fig. 48,1). External flaps Before commencing the journey, close all external flaps and lock them.
Living 6.2.1 Flap lock with recessed handle To open the external flap, pull all the lock handles fitted to that particular external flap at the same time. Fig. 49 Flap lock with recessed handle Opening: Insert key into locking cylinder (Fig. 49,1) and turn a quarter turn. The flap lock is unlatched.
Living Closing: Firmly close the external flap. Turn lock handle in a clockwise direction until it is horizontal. The flap lock is now engaged but not locked. Insert key into locking cylinder. Press down lock handle with key inserted and turn key a quarter turn in a clockwise direction.
Living 6.2.4 Flap for the 230 V connection, square 1 Recessed grip 2 External flap Fig. 52 Flap for the 230 V connection Opening: Reach into the recessed grip (Fig. 52,1) on the external flap (Fig. 52,2) and swing the external flap upward. Closing: Swivel the external flap downwards and press it shut.
Living Furniture flaps Before commencing the journey, close all furniture flaps and inner doors and lock them. The furniture flaps shown in this section are examples. Depending on the model, the locks and handles on the furniture flaps may differ to those dis- played here.
Living 6.3.3 Furniture flaps with release handle Fig. 58 Furniture flap with release handle Opening: Press the release handle (Fig. 58,2) and hold it down. Pull the release handle (Fig. 58,1) until the furniture flap is open. Closing: Press the furniture flap down until you can feel the flap hinge close and hear the lock snap into place.
Living Light switch 6.4.1 Entrance area The light switches shown in this section are examples. Depending on the model, the type and allocation of the light switches may differ to those dis- played here. Fig. 60 Light switch Fig. 61 Awning light The entrance area has light switches for the following lamps: Seating group lights (Fig.
Living Fig. 64 Halogen lamp (example) Fig. 65 Recessed halogen light Further light switches in the living area are located directly on the corre- sponding lamp (Fig. 64,1) or next to the lamp (Fig. 65,1). Fig. 66 Kitchen light In the case of kitchen lights, the light switch (Fig. 66,1) is generally located on the light itself.
Living Light control Functions Depending on the model, the vehicle is fitted with a central lighting system. This lighting system operates and dims single lamps or lamp groups that form part of the lighting system. Furthermore, scene functions are integrated into the lighting system. These scene functions enable the user to save and automatically recall the desired brightness of all lamp groups.
Page 70
Living Symbols The symbols listed in the following table always have the same meaning. Symbol Signification Light scene Main light, living area Indirect lighting, living area Main light, sleeping area Indirect lighting, sleeping area Night light All lamps "OFF" Operation Each button has different functions: Button Press shortly...
Living Spotlight Bulbs and light fittings can be extremely hot. Allow the light bulbs and lamp holders to cool down before touching them. If the light is switched on or still hot, there must always be a safety dis- tance of at least 30 cm between stores or curtains and flammable objects.
Living 6.7.1 Holder on the column The holder for the flat screen is attached to a column. Fig. 72 Holder on the column Positioning: Push the release lever (Fig. 72,2) to the side and turn the holder (Fig. 72,3) with the flat screen to the desired position. Press flat screen slightly upward and swivel it to the desired position.
Living 6.7.3 Holder with jointed arm The flat screen is fastened to a jointed arm. Fig. 74 Holder with jointed arm Positioning: Pull the release knob (Fig. 74,3). The jointed arm (Fig. 74,4) is unlocked. Swivel flat screen into the desired position. Take hold of the flat screen at the top and bottom edge with both hands and set the desired angle of inclination.
Living Windows The windows are fitted with a blind or Roman shade and with an insect screen or folding insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force.
Page 75
Living Fig. 75 Catch lever in "closed" position Fig. 76 Hinged window with rotary hinges, open Opening: Turn the catch lever (Fig. 75,3) a quarter turn towards the centre of the window. Open the hinged window until the required position has been reached and use knurled knob (Fig.
Living 6.9.2 Hinged window with automatic hinges Open the window completely, to release the lock. If the locking device is not released and the window is closed nevertheless, there is the danger of the window breaking due to the massive counter-pressure. When opening the hinged windows, ensure that there are no torsional forces.
Living Turn the catch lever (Fig. 80,3) a quarter turn towards the centre of the window. Slightly open the hinged window outwards. Turn the catch lever a quarter turn towards the window frame. The locking catch (Fig. 80,2) has to be moved into the recess of window catch (Fig.
Living Fig. 82 Catch lever in "closed" position Opening: Turn the catch lever (Fig. 82,1) a quarter turn towards the centre of the window. Open the hinged window to the desired latched position. The automatic hinge automatically locks in place. The hinged window remains locked in the required position.
Living Opening: If the blind is completely closed: Press handle (Fig. 83,2) downwards and, at the same time, tilt it slightly inward. The blind can be taken out of the locking devices situated on both sides of the window frame. If the blind is in an intermediate position: Pull the handle (Fig.
Living 6.9.7 Roman shade and insect screen The windows are fitted with a Roman shade and an insect screen. The insect screen can only be moved together with the Roman shade. Fig. 85 Hinged window Roman shade The Roman shade is located in the bottom blind box. Closing: Grip the Roman shade using the holding bar (Fig.
Living Opening: Grip the Roman shade (Fig. 86,2) in the centre of the holding bar and slowly push it to its initial position. Insect screen The insect screen can be used separately from the Roman shade and can also stay fully closed if required. Closing: Grip the insect screen in the centre of the holding bar (Fig.
Living The skylights are fitted with a blind or Roman shade and with an insect screen or folding insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force.
Living Fig. 90 Heki skylight in ventilation Fig. 91 Ventilation position locking position mechanism Ventilation position The Heki skylight can be put in two ventilation positions: Bad weather position (Fig. 90,1) and central position (Fig. 90,2). Depending on the model, the sky- light can be locked in the central position with the latch (Fig.
Living Closing: Rotate the hand crank until the wind-up skylight is closed. The wind-up sky- light can be locked after rotating two or three more times. Check the locking mechanism. To do so, press your hand against the acrylic glass. Roman shade The Roman shade can be closed in any position, as desired.
Living Reducing size: Open catches (Fig. 94,1). Slightly lift the front of the table-top and pull out. Remove table-top extension (Fig. 93,1) and lay it aside. Lift the table-top slightly and push back as far as possible. Set down the table. Secure the table-top with the catches.
Living Fig. 97 Support frame Fig. 98 Fixed table (from below) Folding out the table-top: Pull out the support frame (Fig. 97,2) below the table-top (Fig. 97,1) to the end position. Fold out the table-top and carefully rest it on the support frame. Folding away the table-top: Lift up the part of the table-top that is folded out and place it carefully on the fixed part of the table-top.
Living 6.11.4 Fixed table (movable table-top) The top of the fixed table can be moved both lengthways and crossways. Fig. 100 Fixed table Moving in a lengthways Loosen knurled screw (Fig. 100,1). direction: Move table-top (Fig. 100,2) to the desired position. Retighten the knurled screw.
Living 6.13 Beds Always use the safety guards supplied. Never remove or dismantle the safety guards supplied. 6.13.1 Bunk bed Only use the upper bunk bed if the safety guard is fitted. The maximum permitted bunk bed load is 100 kg. The upper bunk bed must not be used by children under 6 years of age.
Page 89
Living Fig. 102 Lock Fig. 103 Pull-down bed complete with applied safety net The pull-down bed is located in the driver's cabin above the seats. Opening the pull-down bed: Switch off the lamps underneath the pull-down bed. Rotate the driver's and front passenger's seats in the direction of travel, lock in position, push completely forwards and turn the backrest as far back as possible.
Living Fold up the steps before removing the step ladder. Roman shade The Roman shade is fastened to the ceiling. Only let the Roman shade down if persons are already in the pull-down bed. Fig. 104 Roman shade for pull-down Closing: Unwind cord (Fig.
Page 91
Living Only raise or lower the pull-down bed if it is loaded with a maximum of 15 kg. This maximum load includes the contents of the wall-mounted cup- board at the base of the pull-down bed. If the pull-down bed is overloaded, the overload protection switches off the lifting motor.
Living Overload protection If the pull-down bed meets an obstacle during opening or closing (e.g. a person or a headrest), the overload protection stops the movement. For release, move the pull-down bed with the arrow key in the opposite direction. Safety net If fitted, the safety net (Fig.
Living Fig. 108 Fixed bed The bedding box is located underneath the bed. The bedding box may be used to store bedding. Fold up the slatted frame to place items in the bedding box or to empty it. Depending on the model, the slatted frame may be equipped with a sliding bar. Opening: Lift up the slatted frame (Fig.
Living 6.13.6 Fixed bed (adjustable head section) Do not let the slatted frame fall down when closing the bed! Fig. 110 Adjustable head section Depending on the configuration, the head section of the slatted frame can be adjusted in several stages. Raising the head section: Raise the head section (Fig.
Page 95
Living Fig. 113 Manual control unit Retracting: On the manual control unit (Fig. 113,3) push the " " button (Fig. 113,2) and keep it pressed. The foot section is retracted. The head sections are raised. Extending: On the manual control unit (Fig. 113,3) push the " "...
Living 6.13.8 Widening single beds (special equipment) 1 Mattress 2 Bedside locker cover 3 Bedside locker extension 4 Slatted frame and/or extension 5 Additional cushion Fig. 115 Prior to conversion Fig. 116 During conversion Fig. 117 After conversion Remove the bedside locker cover (Fig. 115,2) and put it to one side. If a locking mechanism is attached to the extension (Fig.
Gas system Chapter overview 7Gas system This chapter contains instructions regarding the gas system of the vehicle. The instructions address the following topics: safety changing the gas bottles gas isolator taps external gas connection automatic switching facility the gas alarm system The operation of the gas operation appliances of the vehicle is described in chapter 9.
Gas system Propane gas is capable of gasification up to -42 °C, whereas butane gas gasifies at 0 °C. Below these temperatures no gas pressure is available. Butane gas is unsuitable for use in winter. Regularly inspect the gas tube fitted to the gas bottle connection for tightness.
Gas system Use the shortest possible tube lengths (150 cm max.) for external gas bottles. Never block the floor ventilation openings below the gas bottles. With some models, the gas bottle compartment is located right next to the conversion door. With these models, only open the gas bottle compartment when the conversion door is closed.
Gas system Gas isolator taps 1 Oven 2 Refrigerator 3 Heater/boiler 4 Cooker Fig. 119 Symbols for the gas isolator taps A gas isolator tap (Fig. 119) for every gas device is built into the vehicle. The gas isolator taps are located in the vehicle at different positions, and can also be fitted separately.
Gas system Connect the external gas device to the connection point (Fig. 120,1). Open the gas isolator tap (Fig. 120,2). Crash protection unit switching facility (special equipment) Do not use the switching facility in closed spaces. When the vehicle is equipped with the crash protection unit the living area heater may be operated during the journey.
Page 102
Gas system Fig. 122 Operating unit Only the electrical functions can be switched at the operating unit (Fig. 122). The regulator taps on the gas bottles (Fig. 121,7) and the release buttons (Fig. 121,6) must be opened manually. The reversing valve provides a constant gas pressure, regardless of which gas bottle is being drawn upon.
Gas system Open regulator tap on the gas bottle. Press the release button for 10 seconds. Turn the knob on the reversing valve to the changed bottle. Open the release button when the display is green. Set the knob on the reversing valve with a half-turn, so that the newly replaced gas bottle will serve as a reserve bottle.
Page 104
Gas system Operating modes The DuoControl switching facility has two operating modes: Winter operation "On and heating" Summer operation "On" Putting into operation: Open the regulator taps on the gas bottles (Fig. 123,1 and 6). Use the knob (Fig. 123,4) on the reversing valve (Fig. 123,3) to select the gas bottle which is to be the primary source of gas (primary bottle).
Gas system Gas alarm system (special equipment) If the gas sensor or a cable is defective, the buzzer sounds until the defect has been rectified. If a deodorant spray, hairspray or a powerful cleaning agent is used in the immediate vicinity of the gas sensor, a false alarm may be triggered. Extended time in a tunnel (traffic jam) may also trigger a false alarm.
Page 106
Gas system I-Modell - 11/12 - Ausgabe 09/11 - 2096165 - BUE-0056-05EN...
Electrical system Chapter overview 8Electrical system This chapter contains instructions regarding the electrical system of the vehicle. The instructions address the following topics: safety explanations of terms relating to the battery 12 V power supply the radio selector switch starter battery living area battery transformer/rectifier panel...
Electrical system Total discharge Total discharge of the battery is imminent, if a battery is completely discharged by an active appliance and by closed circuit current and the off-load voltage falls below 12 V. Total discharge damages the battery. Capacity Capacity refers to the amount of electricity which can be stored in a battery.
Electrical system Operating the radio from the Set the selector switch to the "1" position. The radio will be powered at all living area battery: times from the living area battery. 8.3.2 Starter battery The starter battery serves for starting the engine and supplies the electrical appliances of the base vehicle as well as optional devices such as the radio, navigation system or central locking system with voltage.
Electrical system When charging the starter battery with an external charger, proceed as fol- lows: Turn off the vehicle engine. Switch off the 12 V power supply on the panel. The indicator lamps or the displays on the panel go out. Switch off all gas appliances, all gas isolator taps and close the regulator tap on the gas bottle.
Electrical system Before disconnecting or connecting the terminals of the battery, switch off the vehicle engine as well as the 230 V and 12 V power supplies and all appliances. Danger of short circuit! If the starter battery or living area battery are disconnected, do not apply the ignition.
Page 112
Electrical system Depending on the model, not all slots for the fuses are occupied. If there are several living area batteries, use an auxiliary charging unit. Further information can be obtained in the manufacturer's instruction manual. Fig. 127 Transformer/rectifier (EBL 99) Main supply socket 230 V~ Block 1: Refrigerator output (D+, heating cartridge) Block 2: Refrigerator output from starter battery, alternator D+...
Electrical system 8.4.1 Battery cut-off switch The battery cut-off switch switches off all the appliances in the living area, even inactive ones. Even appliances such as the entrance step, basic lighting or the refrigerator will stop working. This prevents the living area battery from slowly discharging if the vehicle is not used for a longer period of time (e.g.
Electrical system If the vehicle is connected to the 230 V power supply, the living area battery and the starter battery are automatically charged by the charger module on the transformer/rectifier. The starter battery is only charged with a float charge. The charging current is adapted to suit the charging condition of the battery.
Electrical system Functions The transformer/rectifier has the following functions: The transformer/rectifier charges the living area battery. The transformer/ rectifier charges the starter battery with a float charge only. The transformer/rectifier monitors the voltage in the living area battery. The transformer/rectifier distributes the current to the 12 V circuits and secures them.
Electrical system 8.5.3 Battery monitor You must fully recharge a discharged living area battery as soon as pos- sible. The battery monitor in the transformer/rectifier monitors the voltage in the living area battery. If the battery voltage falls below 10.5 V, the battery monitor in the transformer/ rectifier switches off all the 12 V appliances.
Electrical system 8.6.1 12 V main switch The 12 V main switch (Fig. 129,7 and 9) switches the panel and the 12 V power supply to the living area on and off. Exception: Depending on the model, heater, basic light (lighting in the entrance area), entrance step, spare 4 and a refrigerator with automatic power selection system (AES) remain ready to operate.
Page 118
Electrical system Battery voltage Mobile operation Battery opera- Power operation (values during (vehicle moving, tion (vehicle station- operation) no 230 V con- (vehicle station- ary, 230 V con- nection) ary, no 230 V nection) connection) Danger of total 12 V power sup- If appliances are 12 V power sup- 11 V or less...
Electrical system Volume of water/waste The V/tank gauge is for the indication of the quantity of water or waste water. water With the V/tank gauge (Fig. 129,2), use the bottom scale. The gauge automat- ically lights up as soon as a switch is pressed. Displays: Press switch (Fig.
Electrical system Panel IT 994 Further information can be obtained in the manufacturer's instruction manual. V/tank gauge Digital clock/temperature gauge 230 V indicator lamp Current gauge 12 V indicator lamp 12 V main switch Rocker switch for water pump On/ Rocker switch °C for reading internal temperature or external temperature...
Page 121
Electrical system Battery voltage Mobile operation Battery opera- Power operation (values during (vehicle moving, tion (vehicle station- operation) no 230 V con- (vehicle station- ary, 230 V con- nection) ary, no 230 V nection) connection) Danger of total 12 V power sup- If appliances are 12 V power sup- 11 V or less...
Electrical system Volume of water/waste The V/tank gauge is for the indication of the quantity of water or waste water. water With the V/tank gauge (Fig. 130,1), use the bottom scale. The gauge automat- ically lights up as soon as a switch is pressed. Displays: Press the upper part of the rocker switch (Fig.
Electrical system Temperature display The digital clock/temperature gauge is for the indication of the internal or external temperature. The temperature display is only ready for operation if the digital clock display is switched on. After a reading, the respective temperature will be displayed for approx.
Electrical system 8.7.5 12 V main switch The 12 V main switch (Fig. 130,6) switches the panel and the 12 V power supply of the living area on and off. Exception: Depending on the model, heater, basic light (lighting in the entrance area), entrance step, spare 4 and a refrigerator with automatic power selection system (AES) remain ready to operate.
Electrical system Fig. 131 Panel LT 510 230 V indicator lamp Batteries gauge Volt symbol Interior temperature button External temperature button Tank heater button Water tank symbol Tanks gauge Light control button 10 Water pump button 11 Waste water tank symbol 12 Digital display, temperature 13 Tanks button 14 Starter battery button...
Electrical system If, after switching on, the "11.0" LED of the volt indicator and the "V" volt symbol (Fig. 131,3) in the batteries gauge (Fig. 131,2) flash, the voltage of the living area battery is too low. Charge battery. If, after switching on, the "12 V" indicator and the "V" volt symbol (Fig.
Page 127
Electrical system Battery voltage Mobile operation Battery opera- Power operation (values during (vehicle moving, tion (vehicle station- operation) no 230 V con- (vehicle station- ary, 230 V con- nection) ary, no 230 V nection) connection) Danger of total 12 V power sup- If appliances are 12 V power sup- 11 V or less...
Electrical system Current displayed System status "A" ampere symbol -30 A to -10 A Battery is being heavily Lights up red discharged -10 A to -1 A Battery is being dis- Lights up white charged Battery current is low or Lights up white +1 A to +10 A Battery is being charged...
Electrical system Display Signification Remedy The "V" volt symbol The battery voltage has Switch off all 12 V appli- (Fig. 131,3) and the LED fallen below 11 V. Dan- ances and charge the "11.0" flash when the val- ger of total discharge battery either by mobile ues for the living area operation or by connec-...
Electrical system 8.8.8 Switch for water pump The water pump can be turned on and off using the water pump button (Fig. 131,10). Switching on: Press the water pump button (Fig. 131,10). The symbol lights up. Switching off: Press the water pump button (Fig. 131,10). The symbol goes out. The switch status of the water pump is saved when the 12 V power supply is switched off.
Page 131
Electrical system Fig. 132 Fuel cell with tank cartridge Fig. 133 Connector panel of the fuel cell The fuel cell consists of several components that are installed in the rear storage space (Fig. 132) and of an operating unit (Fig. 134) in the living area. The following components are on the fuel cell (Fig.
Page 132
Electrical system The main menu can be accessed with the menu key (Fig. 134,7): Operating mode Fuel cartridge System information Language System reset In the event of faults, the red fault indicator (Fig. 134,5) lights up and a mes- sage appears on the display. The message consists of an error code and infor- mation on how to rectify the fault.
Electrical system Screw tank cartridge connection onto the new tank cartridge. In the "Main Menu > Fuel Cartridge" menu, specify the tank cartridge size used and confirm with "OK". 8.10 Solar installation (special equipment) Protect the solar collectors (solar module) against mechanical overload. The solar installation supplies the most current under optimal sunlight con- ditions.
Electrical system 8.11 230 V power supply Only allow qualified personnel to work on the electrical system. Have the vehicle's electrical system checked by a qualified electrician at least once every 3 years. If the vehicle is used frequently, an annual check is recommended.
Electrical system Fig. 136 230 V fuse box with safety cut- Fig. 137 230 V connection on vehicle out and FI-switch Connecting the vehicle: Check whether the power supply device is suitable regarding connection, voltage, frequency and current. Check whether the cables and connections are suitable. Check the plug connectors and cables for visible damage.
Page 136
Electrical system 1 Unbroken fuse element 2 Broken fuse element Fig. 138 12 V fuse An intact 12 V fuse can be detected by the unbroken fuse element (Fig. 138,1). If the fuse element is broken (Fig. 138,2), change the fuse. Before changing fuses, take the function, value and colour of the relevant fuses from the following specifications.
Page 137
Electrical system FuNo Function Value/colour Cl. 15 (Ignition On) 15 A blue Cl. 30 (constant position) 15 A blue D+ Signal Internal polyswitch (2 A) Spare 15 A blue Front side marker lights (white/red) 5 A light brown Function Value/colour Fuses on the Internal charger module 20 A yellow...
Page 138
Electrical system Function Value/colour Awning light 5 A light brown Antenna 10 A red 10 A red Solar 15 A blue Step 15 A blue Awning 10 A red Gas alarm 2 A grey Pull-down bed 25 A white Fuse for the Thetford The fuse is located in the locker wall of the Thetford cassette.
Page 139
Electrical system Fuse for the Dometic toilet The fuse is located on the rear side of the control unit for the toilet. 1 Control unit 2 Flat fuse 10 A/red Fig. 143 Fuse for toilet Changing: Lift the control unit for the toilet (Fig. 143,1) with a suitable tool and pull it from the wall.
Electrical system 8.12.2 230 V fuse Check the fault current protection switch for each connection to the 230 V power supply, at least once every 6 months. Fig. 146 230 V fuse box with safety cut- out and FI-switch A fault current protection switch (FI-switch) (Fig. 146,4) in the fuse box (Fig.
Page 141
Electrical system Connection possibilities TV socket and SAT socket offer various possibilities for TV operation: Fig. 148 TV inside the vehicle Fig. 149 TV in the awning TV inside the vehicle (Fig. 148,4): Connection to roof antenna (Fig. 148,1) with connection cable (Fig. 148,2) TV inside the vehicle (Fig.
Page 144
Electrical system Fig. 152 Block diagram for panel (IT 96-2) 2 x AMP flat pins 4.8 x 0.8 + 12 V Pump Lumberg MSFQ 5-pin Full Base waste water tank Lumberg MSFQ 6-pin Full Base water tank n. c. Lumberg MSFQ 9-pin 12 V indicator 12 V main switch off 12 V main switch on...
Page 145
Electrical system Fig. 153 Block diagram for panel (IT 994) 2 x AMP flat pins 4.8 x 0.8 + 12 V Pump Lumberg MSFQ 9-pin 12 V indicator 12 V main switch off 12 V main switch on + Starter battery 12 V + Living area battery sensor Negative living area battery sensor 230 V indicator...
Page 146
Electrical system Fig. 154 Block diagram, panel (LT 510) Lumberg MSFQ 6-pin Full Base water tank n. c. Lumberg MSFQ 5-pin Full Base waste water tank Lumberg MSFQ 12-pin Main switch relay 1 off Main switch relay 1 on Main switch relay 2 off Main switch relay 2 on Mains signal Shunt for appliances...
Page 147
Electrical system Lumberg MSFQ 10-pin Pump Tank heater Anti-freeze n. c. Solar starter battery Solar living area battery n. c. n. c. n. c. Lumberg MSFQ 2-pin KTY Pin 1 KTY Pin 2 Lumberg MSFQ 4-pin ADI1 ADI2 +12 V Lumberg MSFQ 4-pin ADI1 ADI2...
Electrical system 8.14.2 Circuit diagram, exterior Fiat Fig. 155 Circuit diagram, exterior Bürstner colours Connection Left side Grey Left direction indicator Blue Fog tail light White Earth return Green Back-up light Brake light Black Left rear light Right side Grey Right direction indicator Blue Fog tail light...
Appliances Chapter overview 9Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction man- uals for the appliances, included separately with the vehicle. The instructions address the following topics: heater air conditioning unit...
Appliances Heater Never let gas escape unburned due to danger of explosion. Never run the heater in gas operation when refuelling, on ferries or in the garage. Danger of explosion! Never operate the heater in gas operation in closed spaces (e.g. garages).
Appliances When five air outlet nozzles are completely opened, less warm air escapes through each nozzle. However, if only three air outlet nozzles are opened, more warm air flows out of each nozzle. 9.2.3 Truma Combi hot-air heater When there is a danger of frost the heater is not in operation, empty the heating system.
Page 152
Appliances The circulation fan automatically switches on when the heater is activated. Switching off: Set the rotary switch (Fig. 158,3) to " " (Fig. 158,4). Close the gas isolator tap "Heater/boiler" and the regulator tap on the gas bottle. After switching off the heater, the circulation fan may still run for a moment to use up the residual heat.
Appliances 9.2.4 Alde hot-water heater (partially special equipment) Never run hot-water heater without heating fluid. Observe notes in chapter 12. Never drill holes in the floor. This might damage the hot-water pipes. The circulating pump must always be turned on when the hot-water heater is in operation.
Page 154
Appliances Start screen The Start screen appears on the display after the heater is switched on. The Start screen contains the following information: Symbol Signification This symbol appears when the circulating pump is activated This symbol appears when a switching facility for gas cylinders is activated This symbol appears when a voltage of 230 V is present at the heater...
Page 155
Appliances If gas and 230 V electrical operation is selected and if the vehicle is con- nected to the 230 V power supply, then the hot-water heater at first only operates in 230 V electric operation. Only if the heat output is insufficient does the gas operation also automatically switch on.
Page 156
Appliances Fig. 162 3-way valve Opening the heat circulation Set the lever (Fig. 162,2) of the 3-way valve (Fig. 162,1) parallel to the in the rear area: straight flow direction (Fig. 162). Locking the heat circulation Set the lever (Fig. 162,2) of the 3-way valve (Fig. 162,1) transverse to the in the rear area: straight flow direction.
Appliances Alde auxiliary circulating pump (special equipment) The auxiliary circulating pump works only if the heat exchanger has been installed and started, and the hot-water heater is running. Fig. 164 Auxiliary circulating pump The auxiliary circulating pump (Fig. 164,1) can be used to heat the vehicle engine when parked.
Appliances Fig. 167 Operating controls for auxiliary heat exchanger Switching on: Push the sliding regulator (Fig. 167,1) of the flow control downward to the desired position. The water circulation is open. Turn the fan switch (Fig. 167,2) for the circulation fan in a clockwise direc- tion.
Appliances Switching on: Connect the vehicle to the 230 V power supply (see chapter 8). Press the rocker switch (Fig. 169,2). The indicator lamp (Fig. 169,1) on the switch is illuminated. Switching off: Press the rocker switch (Fig. 169,2). The indicator lamp (Fig. 169,1) on the switch goes off.
Appliances Setting the time: Press the button (Fig. 170,2). The time setting is displayed by the symbol (Fig. 170,8). Set the time with the buttons (Fig. 170,3 and 6). Programming heating start: Press the button (Fig. 170,5). Set the switching on time within ten seconds, with the buttons (Fig. 170,3 and 6).
Appliances Use the "+" (Fig. 171,19) and "–" (Fig. 171,18) buttons to set the desired temperature. Use the fan speed button (Fig. 171,10) to select the desired fan level. Switching off: Press the ON/OFF button (Fig. 171,9). Fig. 172 Air conditioning unit (Dometic) The LED (Fig.
Page 162
Appliances Following switch-on the air conditioning unit needs approx. 3 minutes until the compressor starts to run and cold air or hot air is output. Also read the manufacturer's instruction manual. Symbol for automatic Symbol for cooling Symbol for heater Temperature (set) display Fan speed display Temperature increase button...
Appliances Boiler Never let gas escape unburned due to danger of explosion. Never run the boiler in gas operation when refuelling, on ferries or in the garage. Danger of explosion! Never operate the boiler in gas operation in closed spaces (e.g. garages).
Page 164
Appliances In summer operation (Fig. 175,1) only the water in the boiler is heated up to either 40 °C or 60 °C. The water is heated to 60 °C in approx. 25 minutes. The yellow indicator lamp (Fig. 175,5) illuminates during the boiler heating-up period.
Page 165
Appliances Switching off: Set the rotary switch (Fig. 175,2) on the operating unit (Fig. 175) to " ". Close the gas isolator tap "Heater/boiler" and the regulator tap on the gas bottle. Variant: Boiler with gas and 230 V electrical operation 230 V electrical operation is only possible when the vehicle is connected to the 230 V power supply.
Appliances Emptying the boiler: Set the rotary switch (Fig. 175,2) on the operating unit (Fig. 175) to " ". Open the safety/drainage valve. To do this turn the knob (Fig. 176,1) par- allel to the safety/drainage valve. The push button (Fig. 176,2) jumps out. The boiler is drained to the outside by the safety/drainage valve.
Appliances For further information, see the separate manufacturer's instruction manual and observe the maintenance instructions found in chapter 12. Position of the drain See chapter 16. cock(s) Cooker Never let gas escape unburned due to danger of explosion. Before using the cooker make sure that there is sufficient ventilation. Open windows or the skylight.
Page 168
Appliances Fig. 179 Gas cooker Switching on: Open the regulator tap on the gas bottle and the gas isolator tap "Cooker". Open the gas cooker lid (Fig. 179,3). Depending on the model, either fold out or set up the flame protection (Fig.
Appliances Press lighting knob (Fig. 180,2). Ignition sparks are generated at the burner. Once the flame is burning, the control knob must be held down for 10 to 15 seconds, until the thermocouple automatically keeps the gas supply open. Release the control knob and turn to the desired setting. Switching off: Turn the control knob to the 0-position.
Page 170
Appliances If the burner flame is accidentally extinguished, turn the control knob to " " and leave the burner off for at least 1 minute. Then ignite it again. Parts of the gas oven become very hot during operation. Never touch hot parts with bare hands.
Appliances Release control knob. Close oven door. Switching the grill on: Open the regulator tap on the gas bottle and the gas isolator tap "Oven". Open the oven door to at least the first locking position (approx. 45°). Press and hold control knob and turn it clockwise to the grill symbol. Keep control knob pressed for a further 5-10 seconds.
Appliances Fig. 184 Operating controls for micro- wave oven Switching on: Press the key (Fig. 184,3) to open the door and place food into the cooking area. Close the door. A clicking noise can be heard when it engages. Select the output on the control knob (Fig. 184,1). Select the cooking time with the control knob (Fig.
Appliances Refrigerator During the journey, only operate the refrigerator via the 12 V power supply. At high ambient temperatures the refrigerator is unable to reach its full cooling power. At high external temperatures, the full cooling power of the cooling unit is only guaranteed if the refrigerator is ventilated sufficiently.
Appliances 9.6.2 Operation (Dometic 7 series with automatic power selection AES and frame heater) Operating modes The refrigerator is equipped with automatic power selection (AES). If the selector switch is set to "AUTO", the AES automatically selects the optimum energy source and regulates the refrigerator operation. Manual intervention to select the type of power is possible but not required.
Page 175
Appliances Change-over between energy sources Open flames are prohibited at petrol stations. If the stop takes longer than 15 minutes, the refrigerator has to be turned off at the energy selector switch. When changing over from 230 V or 12 V to gas, delay times are built into the AES.
Appliances Switching off: Turn the energy selector switch (Fig. 189,3) to " ". No indicator lamp (Fig. 189,4) is lit. Close the gas isolator tap "Refrigerator" and the regulator tap on the gas bottle. Further information can be obtained from the separate instruction manual "Refrigerator".
Page 177
Appliances Gas operation Never let gas escape unburned due to danger of explosion. Open the regulator tap on the gas bottle and the gas isolator tap "Refriger- ator". If the automatic mode is selected, 230 V power supply is not connected and the vehicle's engine is not running, the AES selects the gas supply.
Appliances If the refrigerator is manually set to "12 V", it will constantly consume cur- rent. Therefore, switch over to gas operation when the vehicle engine is not running, and the vehicle is not connected to the 230 V power supply. Switching off: Press down the on/off switch/energy selector switch (Fig.
Page 179
Appliances Closing: Fully close the refrigerator door/freezer compartment door. Push the lock (Fig. 191,1) to the side, so that the closed lock " " (Fig. 191,2) is completely visible. Locking in the ventilation Slightly open refrigerator door/freezer compartment door. position: Push the lock completely to the right.
Sanitary fittings Chapter overview 10Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the vehicle. The instructions address the following topics: water tank waste water tank waste water tank heater complete water system toilet compartment toilet 10.1 Water supply, general Fill water tank from supply systems that have been verified to provide drinking water quality.
Sanitary fittings 10.2 Water tank 10.2.1 Volumes The water tank contains 120 litres. However, the volume has been limited to 60 litres (overflow installed) for payload reasons. The panel has not been adjusted to this volume. The level indicator on the panel shows the actual amount of water in the tank.
Sanitary fittings 10.2.3 Drinking water filler neck with cap The cap for the drinking water filler neck and for the fuel filler neck are very similar. Before filling the tank, always check the label. Fig. 199 Cap for the drinking water filler Fig.
Sanitary fittings Fig. 201 Water tank with handle Closing: Turn the handle (Fig. 201,1) on the water tank in a clockwise direction as far as it will go. Fill the water tank with drinking water. Opening: Turn the handle (Fig. 201,1) on the water tank in an anticlockwise direction as far as it will go.
Sanitary fittings Only empty the waste water tank at disposal stations, camping sites or car- avan sites especially provided for this purpose. 10.3.1 Drain cock underneath the vehicle In case of frost add so much anti-freeze (such as kitchen salt) to the waste water tank so that the waste water cannot freeze.
Page 186
Sanitary fittings Depending on the model, the vehicle is equipped either with a manually oper- ated drain cock or with an electrically operated drainage valve. Fig. 204 Drain cock The drain cock (Fig. 204,1) is accessible from the side storage flap. Fig.
Sanitary fittings 10.3.3 Waste water tank heater (special equipment) Fig. 207 Operating switch Fig. 208 Operating switch (alternative) The waste water tank may be heated and is insulated. The integrated frost guard prevents waste water from freezing. A switch (Fig. 207,1 or Fig. 208) on the front of the bench seat or bed may be used to switch the frost guard on and off.
Sanitary fittings If necessary, switch on the water pump on the panel. Clean or disinfect water system. Close the safety/drainage valve (Truma). Turn the knob perpendicular to the safety/drainage valve and press the push button in. If the temperature is below 6 °C, the safety/drainage valve cannot be closed.
Sanitary fittings Fig. 211 Drain cock (with rocking lever) Fig. 212 Drain cock (with twist cap) To empty and ventilate the water system, proceed as follows. This will avoid frost damage: Position the vehicle horizontally. Switch off water pump on panel. Switch off the 12 V power supply on the panel.
Sanitary fittings For ventilation purposes during or after a shower, and for drying wet clothing, close the toilet compartment door and open the window or the toilet compartment skylight. This improves the air circulation. Close the shower curtain completely when showering, so that no water is able to enter the area between the wash room wall and the shower tray.
Page 191
Sanitary fittings Fig. 214 Removing the Thetford cas- sette Pull out the Thetford cassette as far as it can go. Tip the Thetford cassette slightly and then pull it out completely. Fig. 215 Turning drainage neck Place the Thetford cassette upright. Turn the drainage neck upwards.
Page 192
Sanitary fittings When inserting, do not use force. The Thetford cassette can be damaged. Fig. 217 Inserting the Thetford cassette Push the Thetford cassette back to its original position. Fig. 218 Thetford cassette secured Ensure that the Thetford cassette is secured by the retaining clip. Lock the flap for the Thetford cassette.
Page 193
Sanitary fittings Fig. 220 Pre-flush Fill the toilet bowl with some water. Press the flush button. Flushing con- tinues as long as the button is pressed. Use the toilet. C-200 S cassette With the C-200 S cassette, proceed as follows to flush the toilet: Fig.
Page 194
Sanitary fittings Fig. 223 Opening the sliding trap Open the sliding trap. To do this, press the left side of the sliding trap button. Fig. 224 Closing the sliding trap Flush the toilet. Press the flush button. After flushing close the sliding trap. To do this, press the right side of the sliding trap button.
Page 195
Sanitary fittings Fig. 226 Carrying the Thetford cassette Take the Thetford cassette to a proper disposal area. As you do this, point the drainage neck upwards. Fig. 227 Emptying the Thetford cas- sette Turn the drainage neck upwards. Remove the cap of the drainage neck. Point the Thetford cassette with the drainage neck downwards.
Sanitary fittings 10.7.2 Toilet with fixed seat (Thetford C-402) The Thetford cassette can only be taken out if the sliding trap is closed. Fig. 229 Pulling the retaining clip Preparing toilet: Open the flap for the Thetford cassette and pull the retaining clip upwards to remove the Thetford cassette.
Page 197
Sanitary fittings Fig. 232 Filling with sanitary liquid Fill the Thetford cassette with the specified quantity of sanitary liquid. Then add enough water to completely cover the bottom of the Thetford cas- sette. Close drainage neck with the cap. Return the drainage neck to its original position. When inserting, do not use force.
Page 198
Sanitary fittings Fig. 235 Pre-flush Using the toilet: Fill the toilet bowl with some water. Press the flush button. Flushing con- tinues as long as the button is pressed. Use the toilet. Fig. 236 Operating the sliding trap Open the sliding trap. To do this, turn the slide lever in an anticlockwise direction.
Page 199
Sanitary fittings Fig. 238 Removing the Thetford cas- sette Emptying the Thetford Open the flap for the Thetford cassette and pull the retaining clip cassette: upwards to remove the Thetford cassette. Pull out the Thetford cassette as far as it can go. Tip the Thetford cassette slightly and then pull it out completely.
Sanitary fittings Activate the aeration knob with your thumb. The Thetford cassette empties. Rinse the Thetford cassette thoroughly with fresh water. Close drainage neck with the cap. Return the drainage neck to its original position. Fig. 241 Inserting the Thetford cassette Prepare the Thetford toilet for use.
Page 201
Sanitary fittings Fig. 244 Turning drainage neck Fig. 245 Filling with sanitary liquid Put the sewage tank down vertically. Turn the drainage neck upwards. Remove the cap of the drainage neck. Fill the stated amount of sanitary liquid into the sewage tank. Then add enough water to completely cover the bottom of the sewage tank.
Page 202
Sanitary fittings Removal of sewage tank: Push the slide lever (Fig. 246,1) in. The sliding trap is closed. To empty, the sliding trap of the toilet must be closed. Open the flap for the sewage tank on the outside of the vehicle. Pull up the retaining clip (Fig.
Care Chapter overview 11Care This chapter contains instructions regarding the care of the vehicle. The instructions address the following topics: exterior of the vehicle interior water system extractor hood air conditioning unit winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time.
Care 11.1.3 Washing the vehicle Never clean the vehicle in the car wash. Water can enter the refrigerator grills, the waste gas vents, the ventilation of the extractor hoods or the forced ventilations. The vehicle could be damaged. Wash the vehicle only on a washing site intended for this purpose. Avoid full sunshine.
Care 11.1.6 Waste water tank Clean the waste water tank after every use. Cleaning: Empty the waste water tank. Open the cleaning opening on the waste water tank and the drain cock. Thoroughly rinse out the waste water tank with fresh water. If possible, clean waste water sensors through the cleaning opening by hand.
Care Leather covers should be cleaned with a cotton cloth and a mild soap (curd soap). Make sure that the leather is not soaked through and that no water seeps through the seams of the leather covers. Curtains and net curtains should be dry cleaned. Vacuum clean the carpet, if necessary clean with carpet shampoo.
Care Empty the water system. Close all drain holes and drain cocks. Fill mixture of water and cleaning agent into the water tank. Observe the manufacturer's instructions regarding the mixing ratio. Open the drain cocks one by one. Leave the drain cocks open until the mixture of water and cleaning agent has reached the respective drain.
Care Allow the disinfectant to act in accordance with the manufacturer's instruc- tions. Empty the water system. Collect the mixture of water and disinfectant for correct disposal. For rinsing fill the entire water system with drinking water and empty again several times over.
Care Cleaning the ventilation grill: Use a brush to remove coarse dirt or deposits from the external ventilation grilles. If a cleaning solution is used, ensure that no water ingresses into the inside of the housing. 11.6 Winter care De-icing salt damages the underbody and the parts open to water spray. We recommend that you wash the vehicle more frequently during wintertime.
Care 11.6.3 At the end of the winter season Thoroughly clean the underbody of the vehicle and the engine. When this is done, corrosion-inducing anti-freeze agents (salts, alkaline residues) are removed. Clean the exterior and use regular car wax to protect metal surfaces. 11.7 Lay-up 11.7.1...
Care Activities Done Gas system Close regulator tap on the gas bottle Close all gas isolator taps Always remove gas bottles from the gas bottle compartment, even if they are empty Electrical system Fully charge living area and starter battery Charge the battery for at least 20 hours before laying up.
Care Activities Done Electrical system Remove the starter battery and the living area battery and store them in a place protected from frost (see chapter 8) or connect the vehicle to a 230 V supply Water system Clean the water system using a cleaning agent from a specialised store Complete vehicle Arrange the tarpaulins in such a way that the ventilation openings...
Page 213
Care Activities Done Appliances Check the function of the appliances Change heating fluid of the hot-water heater every 2 years I-Modell - 11/12 - Ausgabe 09/11 - 2096165 - BUE-0056-05EN...
Maintenance Chapter overview 12Maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle. The maintenance instructions address the following topics: doors living area battery fuel cell Alde hot-water heater independent vehicle heater replacing light bulbs At the end of the chapter you will find important instructions on how to obtain spare parts.
Maintenance We recommend either Molykote PG 65 or Vaseline as lubricants. 12.4 Living area battery When replacing the battery, only use the same type of battery (same capacity and voltage, cycle stability). Never use conventional car batteries (starter batteries). A lead acid battery must not be replaced by a dryfill battery.
Maintenance After use, firmly close the cap of the tank cartridge. Insert a new, sealed original tank cartridge into the tank cartridge holder. Secure the tank cartridge with the securing belt. Open cap and keep safe. Screw tank cartridge connection onto the new tank cartridge. In the "Main Menu >...
Maintenance 12.6.1 Checking the fluid level Fig. 250 Compensator reservoir hot- water heater Switch off the hot-water heater and allow it to cool down. Check if the fluid level is between the marks "MIN" (Fig. 250,3) and "MAX" (Fig. 250,2) on the compensator reservoir (Fig. 250). 12.6.2 Topping up heating fluid Position the vehicle horizontally.
Maintenance Switch off the hot-water heater and allow it to cool down. Open bleeding valve (Fig. 251,1) and leave open until no more air escapes. Close bleeding valve. Repeat this procedure at all bleeding valves. Check to see if the hot-water heater warms up. 12.6.4 Position of the bleeding valves Position of the bleeding valves...
Maintenance Position of the bleeding valves I 890 The drain for complete emptying is in the double floor under the water tank (under the vehicle) Underneath the driver's and front passenger's seats In the front bench seat of the central seating group In the storage box of the divan In the lower cupboard to the left of the entrance On the heat exchanger...
Maintenance Before the heating season starts, have the independent vehicle heater checked by an authorised specialist workshop. 12.8 Replacing bulbs, external Bulbs and light fittings can be extremely hot. Therefore, allow lights to cool down before changing bulbs. Store bulbs in a safe place inaccessible to children. Do not use any bulb that has been dropped or which shows scratches in its glass.
Maintenance 12.8.1 Front lights 1 Fog light 2 Daytime running light (LED) 3 Direction indicator 4 Low beam/main beam Fig. 253 Front lights Low beam/main beam The bulbs are changed in the engine compartment. Fig. 254 Low beam/main beam/parking light Open bonnet (see chapter 4).
Maintenance Put in a new bulb. Reassemble the direction indicator in the reverse order. Daytime running light The lights have LEDs. To change the LEDs, contact an authorised dealer or a service centre. Fog light The bulbs are changed in the engine compartment. Fig.
Page 224
Maintenance Fig. 258 Low beam/main beam/parking light Open bonnet (see chapter 4). Put your hand behind the lamp holder (Fig. 254,1). Turn the lamp holder with the lamp in an anticlockwise direction and remove. Turn bulb in an anticlockwise direction and remove from the holder. Put in a new bulb.
Maintenance Install the parking light in reverse order. Fix the plastic apron in reverse order. Direction indicator The bulbs are changed in the engine compartment. Fig. 261 Direction indicator Open bonnet (see chapter 4). Put your hand behind the lamp holder (Fig. 255,1). Turn the lamp holder with the lamp in an anticlockwise direction and remove.
Maintenance Put in a new bulb. Reassemble the lamp in the reverse order. Round lamps 1 Housing screws 2 Rear light/brake light 3 Direction indicator 4 Reverse light (right) and fog tail light (left) Fig. 263 Rear lights Undo the housing screws (Fig. 263,1). Remove housing.
Maintenance 12.8.5 Types of bulbs for exterior lighting Exterior lighting Type of bulb Front Main beam H7 12 V 55 W Low beam H7 12 V 55 W Parking light W5W 12 V 5 W (Viseo) Direction indicator Bay 9s 12 V 21 W BAU 15s 12 V 21 W (Viseo) Fog light H3 12 V 55 W...
Maintenance 12.9.1 Ceiling lamp Fig. 265 Ceiling lamp The ceiling lamp has LEDs. Changing bulbs: Press the two ends (Fig. 265,2) of the spring ring (Fig. 265,1) together and remove. Remove the housing (Fig. 265,3) with LED from the lamp. Pull out the plug and fully replace the housing with LED.
Maintenance 12.9.3 Recessed halogen light (flat) Fig. 268 Recessed halogen light (flat) Halogen bulb G4 12 V/10 W The recessed halogen light (Fig. 268,2) is installed flush with the panel. Changing bulbs: Use a suitable tool (e.g. a screwdriver) to lever out the internal cover ring with glass disk (Fig.
Maintenance 12.9.5 Halogen spotlight (movable) Fig. 270 Halogen spotlight (movable) Fig. 271 Suction cup for replacing the lamp Halogen bulb 12 V/10 W Changing bulbs: Turn the halogen spotlight (Fig. 270,1) by 90° and remove from rail. Turn the lamp shade (Fig. 270,3) in an anticlockwise direction. Withdraw lamp shade complete with halogen bulb (Fig.
Maintenance 12.9.7 Garage light Fig. 273 Garage light Halogen bulb 12 V/21 CP Changing bulbs: Use a suitable tool (e.g. a screwdriver) to carefully lever out the cover (Fig. 273,2) at the notch (Fig. 273,1) and remove it. Remove halogen bulb. Put in a new halogen bulb.
Maintenance The vehicle described in this instruction manual is built and equipped to factory standards. Special equipment is offered depending on its purpose or use. When fitting special equipment check if such equipment has to be entered in the vehicle documents. Observe the max. permissible gross weight. The authorised dealer or service centre will be happy to advise you.
Wheels and tyres Chapter overview 13Wheels and tyres This chapter contains instructions regarding the tyres of the vehicle. The instructions address the following topics: tyre selection handling of tyres changing wheels spare wheel support At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle.
Wheels and tyres Fig. 275 Tighten the wheel nuts or wheel bolts cross-wise Check regularly that the wheel nuts or wheel bolts are firmly seated. Re- tighten the wheel nuts or wheel bolts of a changed wheel cross-wise (Fig. 275) after 50 km (30 miles). See section 13.5.2 for tightening torque.
Wheels and tyres 13.3 Tyre specifications Description Explanation 215/70 R 15C 109/107 Q Tyre width in mm (example) Height-to-width proportion in percent Tyre design (R = radial) Rim diameter in inches Commercial (transporter) Load index code for single tyres Load index code for twin tyres Speed index (Q = 160 km/h) 13.4 Handling of tyres...
Wheels and tyres Never overload the vehicle jack. The maximum permissible load is spec- ified on the vehicle jack's identification plate. Use the vehicle jack only for lifting the vehicle briefly while changing the tyre. No persons may be in the vehicle while it is is raised. Do not start the motor while the vehicle is jacked up.
Page 237
Wheels and tyres Alloy wheel rim Tomason Fig. 277 Alloy wheel rim Tomason Alloy wheel rim 15" Tomason TN3F-6515: Tightening torque 180 Nm Alloy wheel rim 16" Tomason TN3F-6516: Tightening torque 180 Nm Alloy wheel rim Goldschmitt Fig. 278 Alloy wheel rim Goldschmitt Alloy wheel rim 15"...
Wheels and tyres 13.5.3 Changing a wheel The footplate of the vehicle jack must be levelly positioned on the ground. Do not tilt the vehicle jack. The wheel you have replaced should be repaired immediately. Take note of the general instructions in this chapter. Fig.
Wheels and tyres 13.6 Spare wheel support (special equipment) Depending on the model, the spare wheel can be found under the vehicle or in the rear garage. 13.6.1 Spare wheel support under the vehicle The spare wheel is fitted below the body between the frame parts of the chassis.
Wheels and tyres 13.6.3 Spare wheel support in the rear garage Fig. 281 Spare wheel support in the rear garage Removing the spare wheel: Open external flap of the rear garage. Loosen and remove both fixing screws (Fig. 281,2) with the on-board tool set.
Page 241
Wheels and tyres The information on pressure levels is valid for cold tyres and loaded vehi- cles. Pressure in hot tyres must be 0.3 bar higher than in cold tyres. Recheck the pressure when the tyres are cold. Tyre pressures in bar. Over 4.75 bar requires a metal valve.
Troubleshooting Chapter overview 14Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies. The instructions address the following topics: braking system electrical system fuel cell gas system heater boiler air conditioning unit gas cooker...
Page 244
Troubleshooting Fault Cause Remedy No 230 V power supply 230 V automatic circuit Switch on the 230 V au- despite connection breaker has triggered tomatic circuit breaker The mains connection is Check the mains connec- de-energised tion Starter or living area bat- Jumbo flat fuse (50 A) on Replace jumbo flat fuse tery is not charged when...
Page 245
Troubleshooting Fault Cause Remedy No voltage is supplied by Living area battery is dis- Charge living area bat- the living area battery charged tery immediately Total discharge damages the battery. If the vehicle is to be laid up for a long period, fully charge the living area battery beforehand Discharging is caused by...
Troubleshooting 14.3 Fuel cell Do not open the fuel cell. The fuel cell contains no parts that could be repaired by itself. All faults are not displayed. If the faults cannot be rectified using the fol- lowing table or the instruction manual for the fuel cell, please contact the customer service.
Troubleshooting 14.5 Heater/boiler In the event of a defect contact the nearest customer service workshop of the relevant appliance manufacturer. The list of addresses is enclosed with the accompanying appliance documentation. Only authorised qualified personnel may repair the appliance. 14.5.1 Truma heater/boiler Fault Cause...
Troubleshooting 14.5.2 Alde heater/boiler If a fault occurs in the system, the cause is shown on the display. Fault Cause Remedy Heater does not ignite Lack of gas Open regulator tap and with gas operation gas isolator tap Connect a full gas bottle Heater does not ignite Battery voltage too low Charge battery.
Troubleshooting Fault Cause Remedy Water is entering the ve- Drainage holes for con- Clean air conditioning hicle densation are clogged unit Seal is defective Contact customer service No more air circulation Air filter clogged Clean air filter Fan wheel defective Contact customer service 14.6.2 Telair...
Troubleshooting 14.7.2 Microwave oven Only qualified personnel may repair the microwave oven. Improper repairs can cause major risks to the user. Fault Cause Remedy Microwave oven does not Fuse is defective Replace fuse cut in Door of the microwave Remove foreign bodies oven is not properly stuck in the door of the closed...
Troubleshooting Fault Cause Remedy "GAS" indicator lamp Air in the gas pipe Switch off the refrigera- flashes yellow, no gas tor with energy selector switch Open regulator tap on the gas bottle and the gas isolator tap of the re- frigerator Switch on the refrigera- tor with energy selector...
Troubleshooting Fault Cause Remedy Text "GAS" flashes Lack of gas Open regulator tap and gas isolator tap Connect a full gas bottle Cobwebs or burnt resi- Remove the ventilation due in the burning cham- grill on the outside of the vehicle and clean the burning chamber LEDs for display of the...
Page 253
Troubleshooting Fault Cause Remedy Water jets on the shower Water jets calcified De-calcify shower nozzle nozzle clogged in vinegar water (only for products made from met- al) or rub off soft nozzle burling Water drains from the The vehicle is not in a Position the vehicle hori- shower tray slowly or horizontal position...
Troubleshooting 14.10 Body Fault Cause Remedy Flap hinges/door hinges Flap/door hinges are not Lubricate flap hinges/ are difficult to operate sufficiently lubricated door hinges with acid- free and resin-free grease Hinges/joints in the bath- Hinges/joints are not suf- Lubricate hinges/joints room unit/toilet compart- ficiently lubricated with solvent-free and...
Special equipment 15.1 Weight details for special equipment 15Special equipment The use of accessories, parts and fittings not supplied by us may cause damage to the vehicle and jeopardize road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product.
Page 256
Special equipment Item designation Surplus weight (kg) Spare wheel with with 16" support (underneath vehicle) External gas connection Driver's seat, variable height Bike rack for 2 bicycles Bike rack for 2 bicycles, lowerable Bike rack for 3 bicycles Bike rack for 3 bicycles, lowerable Driver's door Floor warming unit Garage door, left...
Page 257
Special equipment Item designation Surplus weight (kg) Motorcycle rack Motorcycle rack in the rear garage Navigation system Fog light Radio preparation Reversing camera Satellite unit (automatic) + LCD television 14-25 Satellite unit (semi-automatic) + LCD television Solar installation 1 x 100 W Solar installation 2 x 100 W Independent vehicle heater Steadies, electrically operated...
Technical data 16.1 View of ground plans 16Technical data Explanations (1) 230 V fuse (2) Transformer/rectifier with 12 V fuses (3) Living area battery with main fuse (4) Water pump mounted in the tank area (5) Drain cock, waste water tank (6) Safety/drainage valve (7) Boiler/heater (8) Water drain cock - yellow...
Page 260
Technical data Fig. 285 Ground plan I 684 P Aviano Fig. 286 Ground plan I 707 Viseo Fig. 287 Ground plan I 709 Aviano Fig. 288 Ground plan I 726 Viseo I-Modell - 11/12 - Ausgabe 09/11 - 2096165 - BUE-0056-05EN...
Page 261
Technical data Fig. 289 Ground plan I 726 Viseo (alternative) Fig. 290 Ground plan I 727 Aviano Fig. 291 Ground plan I 728 G Aviano Fig. 292 Ground plan I 730 Elegance I-Modell - 11/12 - Ausgabe 09/11 - 2096165 - BUE-0056-05EN...
Page 262
Technical data Fig. 293 Ground plan I 737 G Viseo Fig. 294 Ground plan I 739 G Aviano Fig. 295 Ground plan I 800 G Elegance Fig. 296 Ground plan I 810 G Elegance I-Modell - 11/12 - Ausgabe 09/11 - 2096165 - BUE-0056-05EN...
Page 263
Technical data Fig. 297 Ground plan I 821 G Elegance Fig. 298 Ground plan I 870 G Aviano Fig. 299 Ground plan I 875 G Aviano Fig. 300 Ground plan I 890 G Elegance I-Modell - 11/12 - Ausgabe 09/11 - 2096165 - BUE-0056-05EN...
Technical data Fig. 301 Ground plan I 895 G Elegance Fig. 302 Ground plan I 900 Elegance 16.2 Table of linear measures Type Body width, Total length Wheelbase Overall height exterior without ladder without anten- I 640 G 2300 6850 3800 2850 I 684...
Technical data Type Body width, Total length Wheelbase Overall height exterior without ladder without anten- I 890 G 2300 9000 4600 2850 I 895 G 2300 9000 4600 2850 I 900 G 2300 9000 4600 2850 16.3 Power supply Mains connection Protection class I 230 V (±...
Helpful notes Chapter overview 17Helpful notes This chapter contains helpful tips for the journey. The instructions address the following topics: road assistance in European countries traffic rules in European countries gas supply in European countries toll regulations in European countries safe ways to spend the night during travel camping in winter At the end of the chapter there is a checklist containing the most important...
Page 268
Helpful notes Country Emergen- Breakdown service cy services Police Greece ELPA 104 00 171/112 Great Britain AA (08 00) 0 28 90 18 Ireland AA Dublin 18 00 66 77 88 999/112 999/112 Iceland F.I.B 5 11 21 12 Italy ACI 8 00 11 68 00 118/112 Croatia...
Page 270
Helpful notes Country Max. dimen- Gross In built- Outside Motor- sions in me- weight up are- built-up ters areas Width Lgth. Germany 2.55 Up to 3.5 t 3.5 t up to 7.5 t Over 7.5 t Estonia 2.50 Up to 3.5 t Over 3.5 t Finland 2.60...
Page 271
Helpful notes Country Max. dimen- Gross In built- Outside Motor- sions in me- weight up are- built-up ters areas Width Lgth. Romania 2.50 Up to 3.5 t 80/90 Over 3.5 t 80/90 Russia 2.50 Up to 3.5 t Over 3.5 t Sweden 2.60 Up to 3.5 t...
Helpful notes Drivers who have had their driver's licence for less than one year must not drive faster than 90 km/h. Corresponding stickers (available from ACP offices) must be affixed in a clearly visible position on the rear of the vehicle Drivers who have had their driver's licence for less than two years must not drive faster than 70 km/h Swedish campsites often require the motorhome to have a closed waste water...
Page 273
Helpful notes Country Sleeping on Sleeping on Comments roads and privately fields owned lands Italy Staying overnight for one night at car parks and service stations is allowed. Observe the local regulations. Parking and staying overnight on free areas is pro- hibited Croatia Luxembourg...
Helpful notes Country Sleeping on Sleeping on Comments roads and privately fields owned lands Turkey Ukraine Hungary Staying overnight on privately owned land is permitted only with police certification Specifications without guarantee 17.6 Gas supply in European countries In Europe, there are several different connection systems for gas bottles. It is not always possible to fill or exchange your gas bottles in a foreign country.
Helpful notes The risk of thievery is reduced to a minimum when the following basic rules are observed: Before commencing the journey, close and lock all windows, doors and skylights. During high season do not spend the night at highway rest stops or parking areas located along typical vacation routes.
Page 276
Helpful notes Do not leave checking of documents (e.g. vehicle papers and information) as well as checking the condition of the vehicle until just before com- mencing the trip. Planning and checking documents well in advance will save unnecessary trouble. Object Object Object...
Page 277
Helpful notes Object Object Object Vehicle/tools Waste water con- Fabric tape Screwdriver tainer Adapter socket Watering can for Current-measuring drinking water instrument CEE adapter Cable reel Step Wire V-belt Wheel chocks Spare wheel Glue First-aid kit Spare lamps Universal pliers Vehicle jack Spare fuses Compressor...
Inspection plan 18Inspection plan Pos. Component Activity Interval Auxiliary support Lubrication Annually Joints, hinges Lubrication Annually Refrigerator, heater, boiler, cook- Function check Annually er, lighting, flap and door closures, toilet, seat belts Windows, skylights Function check, water Annually ingress test Upholstery, curtains, blinds Visual check Annually...
Page 280
Inspection plan Delivery Pos. 1-11 Stamp of the Bürstner dealer Date Signature 1st year Pos. 1-11 2nd year Pos. 1-14 Stamp of the Bürstner dealer Stamp of the Bürstner dealer Date Signature Date Signature 3rd year Pos. 1-11 4th year Pos.
Page 281
Index 12 V fuses ......135 Antenna alignment ..... . . 55 For Thetford toilet .
Need help?
Do you have a question about the I 2012 and is the answer not in the manual?
Questions and answers
Como ligar relógio e temporizador
To set the clock on a Burstner I 2012:
1. Switch on the digital clock display by pressing the upper part of the rocker switch (Fig.130,11).
2. Use a thin device, such as a biro, to:
- Press into the hour display opening (Fig.130,10) until the correct hour is shown.
- Press into the minute display opening (Fig.130,9) until the correct minutes are shown.
Note:
- The clock continues running even if the display is off.
- If the living area battery is disconnected, the clock resets to 00:00 and must be set again.
No information is provided about setting a timer.
This answer is automatically generated