Sony HCD-GT111 Service Manual
Hide thumbs Also See for HCD-GT111:
Table of Contents

Advertisement

SERVICE MANUAL
Ver. 1.4 2008.10
• HCD-GT111 is the amplifi er, USB, CD player, tape
deck and tuner section in MHC-GT111/GT111BP.
• HCD-GT222 is the amplifi er, USB, CD player, tape
deck and tuner section in MHC-GT222.
• HCD-GT444 is the amplifi er, USB, CD player, tape
deck and tuner section in MHC-GT444.
• HCD-GT555 is the amplifi er, USB, CD player, tape
deck and tuner section in MHC-GT555.
Amplifier section
HCD-GT555
The following are measured at AC 120, 127,
220, 230 – 240 V 50/60 Hz
Front speaker
Power output (rated): 110 W + 110 W
(at 6 , 1 kHz, 1% THD)
RMS output power (reference):
200W + 200 W (per channel at 6 ,
1 kHz, 10% THD)
Subwoofer
RMS output power (reference): 190 W
(at 6 , 100 Hz, 10% THD)
HCD-GT444
The following are measured at AC 120, 127,
220, 230 – 240 V 50/60 Hz
Front speaker
Power output (rated): 90 W + 90 W
(at 6 , 1 kHz, 1% THD)
RMS output power (reference):
150 W + 150 W (per channel at 6 ,
1 kHz, 10% THD)
Subwoofer
RMS output power (reference): 150 W
(at 6 , 100 Hz, 10% THD)
HCD-GT222
The following are measured at AC 120, 127,
220, 230 – 240V 50/60 Hz
Power output (rated): 110 W + 110 W
(at 6 , 1 kHz, 1% THD)
RMS output power (reference):
200 W + 200 W (per channel at 6 ,
1 kHz, 10% THD)
HCD-GT111
The following are measured at AC 120, 127,
220, 230 – 240V 50/60 Hz
Power output (rated): 60 W + 60 W
(at 6 , 1 kHz, 1% THD)
Sony Corporation
9-889-112-05
2008J05-1
Audio&Video Business Group
©
2008.10
Published by Sony Techno Create Corporation
Photo: HCD-GT555
Model Name Using Similar Mechanism
CD
Mechanism Type
Section
Optical Pick-up Block Name
Model Name Using Similar Mechanism
Tape deck
Section
Tape Transport Mechanism Type

SPECIFICATIONS

Laser Diode Properties
RMS output power (reference):
100 W + 100 W (per channel at 6 ,
1 kHz, 10% THD)
Inputs
AUDIO INPUT L/R : voltage
250 mV, impedance 47 kilohms
MIC: sensitivity 1 mV, impedance
10 kilohms
Frequency response: 20 Hz – 20 kHz
(USB) port: Type A
Signal-to-noise ratio: More than 90 dB
Outputs
Dynamic range: More than 88 dB
PHONES: accepts headphones of 8
or
Tape deck section
more
Recording system: 4-track 2-channel, stereo
FRONT SPEAKER: accepts impedance of
6
Tuner section
SUBWOOFER (HCD-GT555/
FM stereo, FM/AM superheterodyne tuner
HCD-GT444 only): accepts
impedance of 6
FM tuner section
Tuning range:
USB section
Supported bit rate
Antenna: FM lead antenna
MP3 (MPEG 1 Audio Layer-3):
Antenna terminals: 75 ohms unbalanced
32 – 320 kbps, VBR
Intermediate frequency: 10.7 MHz
WMA: 32 – 192 kbps, VBR
AAC: 48 – 320 kbps
AM tuner section
Sampling frequencies
Tuning range
MP3 (MPEG 1 Audio Layer-3):
32/44.1/48 kHz
WMA: 44.1 kHz
AAC: 44.1 kHz
Transfer speed
Full-Speed
Supported USB device
Mass Storage Class
Maximum current
500 mA
CD player section
System: Compact disc and digital audio
system
HCD-GT111/GT222/
GT444/GT555
HCD-GT111/GT222/GT444/GT555
Antenna: AM loop antenna, external antenna
Emission Duration: Continuous
terminal
Laser Output*: Less than 44.6 W
Intermediate frequency: 450 kHz
* This output is the value measurement
General
at a distance of 200 mm from the
Power requirements
objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
Power consumption
87.5 – 108.0 MHz (50 kHz step)
Dimensions (w/h/d) (excl. speakers)
Mass (excl. speakers)
Pan American and Oceanian models:
530 – 1,710 kHz (with 10 kHz tuning
interval)
531 – 1,710 kHz (with 9 kHz tuning
interval)
Design and specifications are subject to
European and Russian models:
change without notice.
531 – 1,602 kHz (with 9 kHz tuning
interval)
Other models:
530 – 1,610 kHz (with 10 kHz tuning
interval)
531 – 1,602 kHz (with 9 kHz tuning
interval)
COMPACT DISC DECK RECEIVER
AEP Model
HCD-GT111/GT222/GT444
UK Model
HCD-GT444
E Model
Russian Model
NEW
CDM88A-K6BD93-WOD
KSM-213DCP
HCD-EC55/EC77
TCM-J1 or CS-21SC-900TP
European and Russian models:
AC 230 V, 50/60 Hz
Mexican model: AC 127 V, 60 Hz
Argentine model: AC 220 V, 50/60 Hz
Other models: AC 120, 220 or 230 –
240 V, 50/60 Hz, Adjustable with
voltage selector
HCD-GT555: 216 W
HCD-GT444: 286 W
HCD-GT222: 163 W
HCD-GT111: 150 W
Approx. 231 × 361 × 437.5 mm
(9 1/8 × 14 1/4 × 17 1/4 inch)
HCD-GT555/GT444/GT222
(Except European model),
HCD-GT222 (European model):
9.6 kg
HCD-GT111: 8.0 kg

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-GT111

  • Page 1: Specifications

    HCD-GT444 E Model Russian Model HCD-GT111/GT222/GT444/GT555 • HCD-GT111 is the amplifi er, USB, CD player, tape deck and tuner section in MHC-GT111/GT111BP. • HCD-GT222 is the amplifi er, USB, CD player, tape deck and tuner section in MHC-GT222. • HCD-GT444 is the amplifi er, USB, CD player, tape deck and tuner section in MHC-GT444.
  • Page 2: Table Of Contents

    COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3: Servicing Notes

    HCD-GT111/GT222/GT444/GT555 Ver. 1.4 SECTION 1 SERVICING NOTES MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP – Back Panel – BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostat- MODEL ic break-down because of the potential difference generated by the NUMBE charged electrostatic load, etc.
  • Page 4 HCD-GT111/GT222/GT444/GT555 HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF  Turn a gear by a driver till a lever falls down to the lever position of the figure.  Pull the tray by the hand. gear hole HOW TO REMOVE THE KNOB VOLUME...
  • Page 5 HCD-GT111/GT222/GT444/GT555 CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION In checking the MAIN board, make a capacitor discharge of C803 and C804 for electric shock prevention. POWERAMP board C803 800 /2W 800 /2W POWERAMP board C804 CD MECHANISM BLOCK SERVICE POSITION CD mechanism block...
  • Page 6 HCD-GT111/GT222/GT444/GT555 POWERAMP BOARD SERVICE POSITION POWERAMP board MAIN board TRANS1 board/ TRANS2 board/ TRANSX board front panel block CD mechanism block HOW TO DISTINGUISH TAPE MECHANISM DECK Two kinds of tape mechanism decks installed by this set exist. Please do the repair exchange after confi rming which tape mechanism deck set of the repair according to how to distinguish the fi gure below.
  • Page 7: General

    HCD-GT111/GT222/GT444/GT555 SECTION 2 This section is extracted from instruction manual. GENERAL Guide to parts and controls This manual mainly explains operations using the remote, but the same operations can also be performed using the buttons on the unit having the same or similar names.
  • Page 8: Hooking Up The System Securely

    HCD-GT111/GT222/GT444/GT555 Remote RM-AMU006 N.(rewind/fast forward)  (on/standby) Press to find a point in a track or file. Press to turn on the system. +/– (tuning) Press to select a sound effect. Press to tune in the station you want. /(play)
  • Page 9: Disassembly

    HCD-GT111/GT222/GT444/GT555 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. SIDE L/R CASE (Page 10) 3-3. TOP PANEL BLOCK (Page 10) 3-5. FRONT PANEL BLOCK 3-4. TAPE MECHANISM DECK (Page 11) (Page 11) 3-6.
  • Page 10: Side-L/R Case

    HCD-GT111/GT222/GT444/GT555 Note: Follow the disassembly procedure in the numerical order given. 3-2. SIDE-L/R CASE  four screws (BVTP3 × 10)  three screws (BVTP3 × 10)  four screws (case 3 TP2)  side-L case  side-R case  four screws (case 3 TP2) 3-3.
  • Page 11: Tape Mechanism Deck

    HCD-GT111/GT222/GT444/GT555 3-4. TAPE MECHANISM DECK Note: This illustration is seeing top panel block from inside.  two screws  bracket (deck) (BVTP2.6 × 8)  TC board  two bracket (PWB)  TC shield board  two screws (BVTP2.6 × 8)
  • Page 12: Dc Fan (M102), Back Panel

    HCD-GT111/GT222/GT444/GT555 Ver. 1.4 3-6. DC FAN (M102), BACK PANEL RG DC fan (M102) XT power cord XB cord X bushing bracket bushing RM two screws (BVTP3 × 10) RE two screws RI coating clip (BVTP3 × 12)  fan connector (CN690)  screw RH screw (BVTP3 ×...
  • Page 13: Cd Mechanism Block

    HCD-GT111/GT222/GT444/GT555  screw (BVTP3 × 10) 3-8. CD MECHANISM BLOCK  two screws (BVTP3 × 10)  screw (BVTP3 × 10)  two screws (BVTP3 × 10)  wire (flat type) (31 core) (MAIN board: CN430/CD board: CN201)  screw (BVTP3 ×...
  • Page 14: 3-10. Base Unit

    HCD-GT111/GT222/GT444/GT555 3-10. BASE UNIT  two screws (PTPWHM2.6)  insulator  two springs  two screws (PTPWHM2.6) (insulator)  insulator  two springs (insulator)  base unit  insulator  insulator CD mechanism block – Bottom view – 3-11. OP BASE ASSY (KSM-213D)
  • Page 15: Belt (Dlm3A)

    HCD-GT111/GT222/GT444/GT555 3-12. BELT (DLM3A) position of belt belt  cover  four screws belt  two belts (DLM3A)
  • Page 16: Test Mode

    HCD-GT111/GT222/GT444/GT555 SECTION 4 TEST MODE 2. The CD ring indicators fl ash on the fl uorescent indicator tube. PANEL TEST MODE The function is changed to AUDIO and the volume is changed This mode is used to check the fl uorescent indicator tube, LEDs, to VOLUME MIN.
  • Page 17 HCD-GT111/GT222/GT444/GT555 TUNER STEP CHANGE Aging mode sequence: (Except GT111: AEP, Russian/GT222: AEP, Russian/ START (from GT444: AEP, Ruissian, UK/GT555: Russian models) Disc 1) The step interval of AM channels can be toggled between 9 kHz and 10 kHz. This mode is not available for Saudi Arabian, Euro- pean and Russian models.
  • Page 18 HCD-GT111/GT222/GT444/GT555 Display of no disc errore Display of Total Error D*$$%%&&##00 D* : The number of no disc error (“0” is latest one) (Press [>] button to display next error) FF button FR button $$ : Error type 01 : Focus error...
  • Page 19 HCD-GT111/GT222/GT444/GT555 CD TRAY LOCK MODE METER TEST MODE This mode let you lock the disc tray. When this mode is activated, This mode is used to check the meter device. the disc tray will not open when [OPEN/CLOSE] button or [DISC Procedure: SKIP/EX-CHANGE] button is pressed.
  • Page 20: Mechanical Adjustments

    HCD-GT111/GT222/GT444/GT555 SECTION 5 MECHANICAL ADJUSTMENTS PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demag- netizer. (Do not bring the head magnetizer close to the erase head.)
  • Page 21: Electrical Adjustments

    HCD-GT111/GT222/GT444/GT555 SECTION 6 ELECTRICAL ADJUSTMENTS Adjustment Location: Record/Playback/Erase Head DECK SECTION 0 dB = 0.775V 1. Demagnetize the record/playback head with a head demagne- tizer. 2. Do not use a magnetized screwdriver for the adjustments. TEST TAPE Tape Signal Used for P-4-A063 6.3 kHz, -10 dB...
  • Page 22 HCD-GT111/GT222/GT444/GT555 RF LEVEL CHECK TUNER SECTION oscilloscope FM TUNE LEVEL CHECK CD board signal TP123 (RFO) generator TP124 (VC) Procedure : 1. Connect an oscilloscope to TP123 (RFO) and TP124 (VC). Procedure: 1. Turn on the set. 2. Turn the power ON.
  • Page 55 HCD-GT111/GT222/GT444/GT555 – MAIN Board – IC407 R2A15216FP REFERENCE INDR INDL 6 INPUT 6 INPUT SELECTOR SELECTOR INER INEL (R-CH) (L-CH) INFR INFL GAMER GAMEL INGAINOUTR INGAINOUTL RECAR RECAL RECBR RECBL VOCAL CUT SURROUND OR DPL IN TRER TREL TONE TONE...
  • Page 56 HCD-GT111/GT222/GT444/GT555 – DISPLAY Board – IC1101 NJU3427FH2 51 50 49 48 46 45 RESET SERIAL CIRCUIT BUFFER INSTRUCTION TIMING DUTY DECODER COUNTER COUNTER ADDRESS DISPLAY DR35 COUNTER DATA RAM DR34 DR33 DR32 SEGMENT TIMING DR31 DATA LATCH DECODER DR30 DR29...
  • Page 57 HCD-GT111/GT222/GT444/GT555 • IC Pin Function Description CD BOARD IC101 TC94A70FG-101 (CD-MP3 PROCESSOR) Pin No. Pin Name Description AVSS3 Ground terminal RFZi RF ripple zero crossing signal input terminal RFRP RF ripple signal output terminal SBAD/RFDC Sub beam addition signal or RF peak detection signal output terminal...
  • Page 58 HCD-GT111/GT222/GT444/GT555 Pin No. Pin Name Description Not used SFSY/LOCK Not used ZDET Zero detection signal output terminal Not used GPIN Not used Microcomputer interface mode selection signal input terminal Fixed at "H" in this set DOUT (PO6) Digital audio data output terminal...
  • Page 59 HCD-GT111/GT222/GT444/GT555 USB BOARD IC901 TMP92CD28AFG-7AC9 (TEM) (USB CONTROLLER) Pin No. Pin Name Description /RESET Reset signal input from the system controller "L": reset Ready to send signal input from the system controller 3, 4 NO USE Not used Function selection signal input terminal Fixed at "L"...
  • Page 60 HCD-GT111/GT222/GT444/GT555 Pin No. Pin Name Description Two-way EEPROM IIC clock bus terminal Not used Bit clock signal output to the CD-MP3 processor DATA Audio data output to the CD-MP3 processor GATE Gate signal output to the CD-MP3 processor DVCC Power supply terminal (+3.3 V)
  • Page 61 HCD-GT111/GT222/GT444/GT555 MAIN BOARD IC401 R5F3640DDFA (SYSTEM CONTROLLER) Pin No. Pin Name Description METER-IN3, 1, 2 Meter motor drive signal output to the motor drive (GT222/GT444/GT555) METER-IN4 SW LED LED drive signal output terminal for SUBWOOFER indicator (GT222/GT444/GT555) SIRCS SIRCS signal input from the remote control receiver...
  • Page 62 HCD-GT111/GT222/GT444/GT555 Pin No. Pin Name Description ST-TUNED Tuned detection input from the tuner (FM/AM) Power supply terminal (+3.3V) ST-CE PLL chip enable signal output to the tuner (FM/AM) Ground terminal ST-DIN PLL serial data output to the tuner (FM/AM) ST-CLK...
  • Page 63: (Gt222/Gt444/Gt555)

    HCD-GT111/GT222/GT444/GT555 SECTION 8 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • Color Indication of Appearance Parts Ex- : Chilean and Peruvian models they may have some difference from the ample: : Mexican model original one. KNOB, BALANCE (WHITE) . . . (RED) : Russian model •...
  • Page 64: Loading Panel Section

    HCD-GT111/GT222/GT444/GT555 Ver. 1.4 8-2. LOADING PANEL SECTION back panel section DISPLAY BOARD section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-283-215-01 PANEL, LOADING (GT111: AEP, RU, E2, E51, AR) 3-283-215-41 PANEL, LOADING (GT111: E3) 3-283-215-11...
  • Page 65: Display Board Section

    HCD-GT111/GT222/GT444/GT555 Ver. 1.4 8-3. DISPLAY BOARD SECTION meter display panel assy (GT222/ GT444/GT555) FFC001 not supplied (VOLUME board) S1051 DISPLAY board supplied supplied with S1051 front panel section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark...
  • Page 66: Front Panel Section

    HCD-GT111/GT222/GT444/GT555 Ver. 1.4 8-4. FRONT PANEL SECTION not supplied not supplied not supplied not supplied not supplied (MIC board) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-2188-449-3 FRONT PANEL ASSY (GT111: AEP, RU, E2, E51,...
  • Page 67: Meter Display Assy

    HCD-GT111/GT222/GT444/GT555 8-5. METER DISPLAY ASSY not supplied (LED board: GT222/GT444/GT555, LED (GSL1) board: GT111) not supplied not supplied not supplied (MOTOR DRIVE board) supplied not supplied supplied supplied not supplied not supplied not supplied not supplied (GT222/GT444/GT555) (SW board) Ref. No.
  • Page 68: Top Panel Section

    HCD-GT111/GT222/GT444/GT555 8-6. TOP PANEL SECTION not supplied not supplied #1: except AEP, RU, UK not supplied #3: AEP, RU, UK not supplied not supplied (TC SHIELD board) not supplied TC board (AEP, RU, UK ) FFC502 not supplied Note: When you exchange Ref .No. 260, 261 or 262, Please refer to “HOW TO DISTIN-...
  • Page 69: Back Panel Section

    HCD-GT111/GT222/GT444/GT555 8-7. BACK PANEL SECTION M102 (GT222/GT444/GT555) supplied not supplied M101 supplied not supplied (5V REG board) not supplied (SW JACK board) not supplied IC050 (GT444/ GT555) not supplied not supplied MAIN BOARD section not supplied (USB board) Ref. No.
  • Page 70: Main Board Section

    HCD-GT111/GT222/GT444/GT555 Ver. 1.4 not supplied (9V REG board) 8-8. MAIN BOARD SECTION not supplied not supplied (GT111) FFC220 MAIN chassis section board Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1444-551-A MAIN BOARD, COMPLETE (GT111: AEP)
  • Page 71: Chassis Section

    HCD-GT111/GT222/GT444/GT555 Ver. 1.4 8-9. CHASSIS SECTION not supplied (TRANS1 board (GT111: E2, E3, E51)/ TRANS2 board (GT222/GT444/GT555)/ TRANSX board (GT111: AEP, RU, AR)) F908 F904 (GT222/GT555) F905 F909 F907 F906 PT901 not supplied not supplied (BU FFC board) not supplied...
  • Page 72: Cd Mechanism Section (Cdm88A-K6Bd93-Wod)

    HCD-GT111/GT222/GT444/GT555 8-10. CD MECHANISM SECTION (CDM88A-K6BD93-WOD) not supplied (including sled motor (M402), spindle motor (M401)) not supplied sled motor (M402) spindle motor (M401) S201 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-797-193-31 MECHANICAL, CD (DLM3A) (MX) 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING...
  • Page 73: Electrical Parts List

    HCD-GT111/GT222/GT444/GT555 SECTION 9 5V REG 9V REG ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • RESISTORS : Mexican model the parts list may be different from the All resistors are in ohms. : Russian model parts specifi ed in the diagrams or the com- METAL: Metal-fi...
  • Page 74 HCD-GT111/GT222/GT444/GT555 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C302 1-137-710-91 CERAMIC CHIP 10uF 6.3V R151 1-216-864-11 SHORT CHIP C303 1-137-710-91 CERAMIC CHIP 10uF 6.3V R153 1-216-857-11 METAL CHIP 1/10W C306 1-128-995-21 ELECT CHIP 100uF R154...
  • Page 75 HCD-GT111/GT222/GT444/GT555 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1444-539-A DISPLAY BOARD, COMPLETE (GT111: AEP, RU) < FLEXIBLE FLAT CABLE > A-1444-582-A DISPLAY BOARD, COMPLETE (GT222: AEP, RU) A-1444-600-A DISPLAY BOARD, COMPLETE FFC001 1-833-945-21 CABLE, FLEXIBLE FLAT (11 CORE)
  • Page 76 HCD-GT111/GT222/GT444/GT555 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1130 1-216-819-11 METAL CHIP 1/10W R1181 1-216-825-11 METAL CHIP 2.2K 1/10W (GT111/GT222/GT444) R1182 1-216-827-11 METAL CHIP 3.3K 1/10W R1130 1-216-821-11 METAL CHIP 1/10W R1183 1-216-829-11 METAL CHIP 4.7K...
  • Page 77 HCD-GT111/GT222/GT444/GT555 DISPLAY LED (GSL1) MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R019 1-216-821-11 METAL CHIP 1/10W S1191 1-762-875-21 SWITCH, KEYBOARD (ENTER) R020 1-216-833-11 METAL CHIP 1/10W S1192 1-762-875-21 SWITCH, KEYBOARD (RETURN) ************************************************************* S1193 1-762-875-21...
  • Page 78 HCD-GT111/GT222/GT444/GT555 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark (GT111/GT555) C137 1-126-964-11 ELECT 10uF C241 1-162-964-11 CERAMIC CHIP 0.001uF C242 1-162-962-11 CERAMIC CHIP 470PF C139 1-126-961-11 ELECT 2.2uF C243 1-100-717-91 CERAMIC CHIP 1uF C142 1-126-964-11...
  • Page 79 HCD-GT111/GT222/GT444/GT555 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C611 1-104-658-91 ELECT 100uF D211 6-501-722-01 DIODE MAZ8043GMLS0 C612 1-100-597-91 CERAMIC CHIP 0.1uF D212 6-501-817-01 DIODE MA2J1110GLS0 C615 1-100-597-91 CERAMIC CHIP 0.1uF D213 6-500-334-01 DIODE MC2836-T112-1...
  • Page 80 HCD-GT111/GT222/GT444/GT555 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JR117 1-216-296-11 SHORT CHIP Q681 6-551-276-01 TRANSISTOR RT1N431C-TP-1 JR118 1-216-864-11 SHORT CHIP Q684 8-729-037-13 TRANSISTOR KTA1271Y JR119 1-216-296-11 SHORT CHIP Q690 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF JR120 1-216-296-11...
  • Page 81 HCD-GT111/GT222/GT444/GT555 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R190 1-216-857-11 METAL CHIP 1/10W R229 1-216-825-11 METAL CHIP 2.2K 1/10W R192 1-216-842-11 METAL CHIP 1/10W R241 1-216-845-11 METAL CHIP 100K 1/10W R194 1-216-822-11 METAL CHIP 1.2K...
  • Page 82 HCD-GT111/GT222/GT444/GT555 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R391 1-216-833-11 METAL CHIP 1/10W R493 1-216-819-11 METAL CHIP 1/10W R392 1-216-815-11 METAL CHIP 1/10W (GT222: MX/GT444: MX/GT555: MX) (GT222) R493 1-216-821-11 METAL CHIP 1/10W R392...
  • Page 83 HCD-GT111/GT222/GT444/GT555 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R647 1-216-841-11 METAL CHIP 1/10W C711 1-124-584-00 ELECT 100uF 6.3V R648 1-216-841-11 METAL CHIP 1/10W C712 1-162-923-11 CERAMIC CHIP 47PF R649 1-216-817-11 METAL CHIP 1/10W C713...
  • Page 84 HCD-GT111/GT222/GT444/GT555 Ver. 1.4 MOTOR DRIVE POWERAMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MOTOR DRIVE BOARD (GT222/GT444/GT555) C804 1-137-842-11 ELECT (BLOCK) 2200uF (GT222/GT555) ****************** < CAPACITOR > C805 1-127-811-11 ELECT (BLOCK) 3300uF (GT222: E2, E51, MX, AR/GT555: E2, E51, MX, AR)
  • Page 85 HCD-GT111/GT222/GT444/GT555 Ver. 1.2 POWERAMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D806 6-500-968-21 DIODE 30PRA20FC (GT222/GT555) D807 6-501-817-01 DIODE MA2J1110GLS0 R809 1-216-797-11 METAL CHIP 1/10W D808 6-501-817-01 DIODE MA2J1110GLS0 (TYPE A) (TYPE A/TYPE B/GT111 (TYPE C): AEP, RU/...
  • Page 86 HCD-GT111/GT222/GT444/GT555 Ver. 1.2 POWERAMP SW JACK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R830 1-216-841-11 METAL CHIP 1/10W R881 1-216-838-11 METAL CHIP 1/10W 0 R831 1-220-893-11 METAL 0.22 (GT444/GT555) 0 R832 1-220-893-11 METAL 0.22 R881...
  • Page 87 HCD-GT111/GT222/GT444/GT555 SW JACK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C548 1-162-964-11 CERAMIC CHIP 0.001uF < RESISTOR > < CONNECTOR > R870 1-216-797-11 METAL CHIP 1/10W R873 1-216-797-11 METAL CHIP 1/10W CN501 1-815-449-11 PIN, CONNECTOR (PWB) 8P...
  • Page 88 HCD-GT111/GT222/GT444/GT555 TRANS1 TRANS2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R531 1-216-832-11 METAL CHIP 8.2K 1/10W < RESISTOR > R532 1-216-832-11 METAL CHIP 8.2K 1/10W R533 1-216-837-11 METAL CHIP 1/10W R904 1-216-821-11 METAL CHIP 1/10W...
  • Page 89 HCD-GT111/GT222/GT444/GT555 TRANS2 TRANSX Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSFORMER > FH910 1-533-217-31 FUSE HOLDER FH913 1-533-217-31 FUSE HOLDER 0 PT902 1-443-927-11 TRANSFORMER, POWER FH914 1-533-217-31 FUSE HOLDER (GT222: MX/GT444: MX/GT555: MX) FH915...
  • Page 90 HCD-GT111/GT222/GT444/GT555 USB CONNECTOR VOLUME Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN907 1-784-833-51 CONNECTOR, FFC (LIF (NON-ZIF)) 21P R973 1-216-809-11 METAL CHIP 1/10W R974 1-216-809-11 METAL CHIP 1/10W < DIODE > R975 1-216-809-11 METAL CHIP...
  • Page 91 HCD-GT111/GT222/GT444/GT555 Ver. 1.4 VOLUME Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < ROTARY ENCODER > ACCESSORY ********** S1051 1-478-133-11 ENCODER, ROTARY (OPERATION DIAL) S1052 1-480-136-11 ENCODER, ROTARY (12 TYPE) 1-569-008-22 ADAPTOR, CONVERSION 2P (E2, E3, E51)
  • Page 92 HCD-GT111/GT222/GT444/GT555 MEMO...
  • Page 93: Revision History

    TC (Suffi x-14), TRANS1 (Suffi x-13) and USB CONNECTOR (Suffi x-14) boards (SUPPLEMENT-1) (SMR-08081) 2008.09 Addition of Mexican model (HCD-GT111) Change of 5V REG (Suffi x-14), POWERAMP (Suffi x-13) and VOLUME (Suffi x-15) boards Change of 9V REG (Suffi x-13), DISPLAY (Suffi x-15), MAIN (Suffi x-14), MIC (Suffi x-15), SW JACK (Suffi...

This manual is also suitable for:

Hcd-gt222Hcd-gt444Hcd-gt555

Table of Contents