Lincoln Electric VANTAGE 400 Service Manual page 26

C-2
FIELD INSTALLED OPTIONS / ACCES-
SORIES
K2641-2 FOUR WHEELED STEERABLE YARD TRAILER
For in plant and yard towing. Comes standard with a Duo-Hitch™, a
2" Ball and Lunette Eye combination Hitch.
K2636-1 TRAILER - Two-wheeled trailer with optional fender and
light package. For highway use, consult applicable federal, state,
and local laws regarding possible additional requirements. Comes
standard with a Duo-Hitch™, a 2" Ball and Lunette Eye combination
hitch. Order:
K2636-1 Trailer
K2639-1 Fender & Light Kit
K2640-1 Cable Storage Rack
K903-1 SPARK ARRESTOR - Includes a heavy gage steel,
approved spark arrestor, clamp and adapter for mounting to the muf-
fler exhaust pipe.
K704 ACCESSORY SET - Includes 35 ft. (10m) of electrode cable
and 30 ft. (9.1m) of work cable, head shield, work clamp electrode
holder. Cables are rated at 400 amps, 100% duty cycle.
K857 25 ft (7.6m) or K857-1 100 ft. (30.4m) REMOTE CONTROL
Portable control provides same dial range as the output control on
the welder. Has a convenient 6 pin plug for easy connection to the
welder.
K802N POWER PLUG KIT
Provides four 120 volt plugs rated at 20 amps each and one dual
voltage, full KVA plug rated at 120/240 volts, 50 amps.
K802R POWER PLUG KIT
Provides four 120 volt plugs rated at 15 amps each and one dual
voltage, full KVA plug rated at 120/240 volts, 50 amps.
T12153-9 50 AMP, 120/240V POWER PLUG (1-Phase)
T12153-10 50 AMP, 240V POWER PLUG (3-Phase)
K1816-1 FULL KVA ADAPTER KIT
Plugs into the 120/240V NEMA 14-50R receptacle on the case front
(which accepts 4-prong plugs) and converts it to a NEMA 6-50R
receptacle, (which accepts 3-prong plugs.) For connection of Lincoln
equipment with NEMA 6-50 Plug.
K1858-1 SERVICE INDICATOR KIT- Provides a GO / NO-GO visu-
al indication of air cleaner element useful service life. Filter service
based on restriction readings allows the longest life possible from the
filter and best engine protection.
K2679-1 COLD WEATHER HEATER AND TARP KIT
For engine starting and operation in extreme cold weather conditions
down to -40ºF / -40ºC (with the use of OW40 synthetic oil and arctic
diesel fuel), includes 120VAC engine block heater, and radiator grill
tarp.
ACCESSORIES
WIRE FEEDER OPTIONS
K449 LN-25 - Includes internal contactor for across the arc
operation (no control cable). Provides "cold" electrode until
gun trigger is pressed. Includes gas solenoid.
K1870-1 LN-15 Across the Arc Wire Feeder.
Portable, lightweight, compact CC/CV unit for flux-cored and
MIG welding. Includes Gas Solenoid, adjustable flow meter
and internal contactor. For 10-15 lb. (4.5-6.8kg) spools.
Magnum Gun and Magnum Gun Connector Kit are required
for gas-shielded welding. Innershield Gun is required for gas-
less welding.
K126-2 Magnum 350 Innershield Gun
K1802-1 Magnum 300 MIG Gun (for LN-25)
K470-2 Magnum 300 MIG Gun (for LN-15, Includes
Connector Kit)
K466-10 Connector Kit (for LN-15, K470-2)
K1500-1 Gun Receiver Bushing (for LN-15 & K126-2)
K487-25 Magnum SG Spool Gun
Hand held semiautomatic wire feeder. Requires SG Control
Module and Input Cable.
K488 SG Control Module (For Magnum Spool Gun)
The Interface between the power source and the spool gun.
Provides control of the wire speed and gas flow. For use
with a K487-25 spool gun.
K691-10 Input Cable (For SG Control Module)
For Lincoln engine power sources with 14-pin MS-type con-
nection, separate 115V NEMA receptacles and output stud
connections.
Note: See Wire Feeder IM manuals for appropriate Drive
Roll and Guide Tubes.
TIG OPTIONS
K1783-9 Pro -Torch® PTA-26V TIG Torch
Air Cooled 200 amp torch (2 piece) equipped with valve for
gas flow control. 25 ft. (7.6m) length.
KP509 Magnum Parts Kit for PTA-26V TIG Torch
Magnum Parts Kit provides all the torch accessories you
need to start welding. Parts kit provides collets, collet bod-
ies, a black cap, alumina nozzles and tungstens in a variety
of sizes, all packaged in an easy to carry reclosable sack.
K870 Foot Amptrol®
K963-3 Hand Amptrol®
K2347-1 Precision TIG 185 Ready-Pak(For AC TIG)
K2350-1 Invertec® V205-T AC/DC One-Pak™ Package
(For AC TIG)
PLASMA CUTTING
K1580-1 Pro-Cut 55
Cuts metal using the 3-phase AC generator power from the
engine driven welder. Accepts 3-phase or 1-phase input
power. Requires the K1816-1 Full KVA adapter kit, if con-
nected for 1-phase input power.
VANTAGE® 400
C-2