Huviron SK-B300(D)/HD21 Manual

HD-SDI CAMERA
SK-B300(D)/HD21
MANUAL
FEATURES
1. 1/2.9" SONY CMOS
2. Full HD Resolution
3. DAY & NIGHT Function
4. WDR (Wide Dynamic Range)
5. 3D DNR Fucntion
6. Privacy mask function 28 area
7. On Screen Display menu
8. Intelligent motion detection 4 area
9. Output : HD-SDI/CVBS
10. Protocol RS-485 : PELCO - P, PELCO - D
CAUTION AND WARNING
1. Do not install the camera outdoors.
Use weather-proof housing for outdoor.
2. Choose an ideal location for the camera, since the
camera unit must be protected against moisture and
vibration.
3. Be careful not to scratch the camera unit, especially
lens glass.
4. Use the camera under proper temperature.
(-10℃ ~ +50℃)
5. Handle with care. Dropping it can cause serious
damage to the camera.
6. Avoid any direct sun light into the lens.
7. Use the adaptor regulated 12V DC, 500mA.
Dual voltage product can use 24V AC, 500mA adaptor.
(Option)
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
DESCRIPTION OF OPERATION
1. Remove the protective rubber before installing a CS
mount lens.(If you use a C mount lens, add a C mount
ring. - option)
2. Connect the video output jack to the monitor video in
jack.
3. Connect power supply. Check the voltage.
LENS CONNECTION
(option)
1. Manual iris lens
1) Before mounting a lens, please check whether it is
a C mount or CS mount lens.
2) CS mount lens : After removing the protective
rubber, attach the lens.
3) C mount lens : Before installing the lens, attach the
C mount ring to the camera.
4) Set the LENS mode to "manual" by OSD.
C-MOUNT RING(option)
BACK FOCUS CONTROL
2. Auto iris lens
1) Attach a DC lens as like the manual lens connection.
2) Connect the lens plug to the auto iris lens connector
on the rear panel of the camera.
3) Set the LENS mode to DC and adjust DC level by
OSD.
BACK FOCUS CONTROL
Auto Iris Lens Connector
DC-TYPE
② ①
①DAMP COIL -
②DAMP COIL +
③DRIVE COIL +
④ ③ ④DRIVE COIL -
ACCESSORIES
C MOUNT RING - (option)
OVERVIEW
②
POWER
CVBS HD-SDI
U
① L R
D E
④
AC24V~
1 2 3 4 5
DC12V
①Menu setup buttons :
ㆍENTER : Used to access the menu and confirm
selection.
ㆍUp, Down : Used to move the cursor to up or
down.
ㆍLeft, Right : Used to move the cursor to left or
right and change the value.
②CVBS output : Composite analog video output
③HD-SDI output : HD-SDI digital video output
④Input/Output terminal :
1. GND : GROUND terminal
2. D/N IN : Switch to Day & Night Mode by
connecting an external signal to this port
(Using an 'EXT' mode in Day&Night menu)
3. MD OUT : Motion detection signals are
output through this port
4. RS-485A : Connect the control unit via a twi s ted,
2-conductor line to the port. RS-485A(+)
5. RS-485B : Connect the control unit via a twi s ted,
2-conductor line to the port. RS-485B(-)
⑤Power input terminal : You can connect 12V DC
regardless polarity.(Dual power product can
use 24V AC)
DIMENSION
59.8
109.4
③
⑤
43.4
1/4"-20UNC(20THREAD)
59.4
L : 4.5mm±0.2mm
(ISO standard)
TROUBLESHOOTING GUIDE
Before calling service, check the following points for
possible misuse.
Check point
Problem
Too dark or bright Readjust the contrast or brightness
picture controls on the monitor.
Check for power connection
No Power
Clean the camera lens.
Poor picture quality
Readjust lens focus.
Check the condition of the power
Shrinking picture
sources.
If you can't correct the problem after going through this
chart, contact a service professional for further assistance.
POWER
CVBS HD-SDI
U
L R
D E
1 2 3 4 5 AC24V~
DC12V
.