Oppladbar Multi-kutter Ladattava monitoimileikkuri Model No: EY4542 Before operating this unit, please read these instructions completely and save this manual for future use. Vor Inbetriebnahme des Gerätes die Betriebsanleitung bitte gründlich durchlesen und diese Broschüre zum späteren Nachschlagen sorgfältig aufbewahren.
Original instructions: English WARNING Translation of the original instructions: Read all safety warnings and all instructions. Other languages Failure to follow the warnings and instructions Read “the Safety Instructions” booklet may result in electric shock, fire and/or serious and the following before using. injury.
3) Adjust the cutting depth to the thickness either side of the blade, but not in line of the workpiece. Less than a full tooth of with the blade. the blade teeth should be visible below the Kickback could cause the saw to jump back- work-piece.
10) Be sure to inspect material. Avoid cutting WARNING other different material. 11) Be careful not to drop the tool. • Do not use other than the Panasonic battery packs that are designed for use with this 12) Never swing the tool. rechargeable tool.
. OPERATION • Never use other than the dedicated charger to charge the battery pack. Otherwise, the Before Using the Tool battery may leak, overheat, or explode. • After removing the battery pack from the This tool is intended to cut unhardened fer rous tool or the charger, always reattach the pack metal, nonferrous metal, wood, and plastic.
5. Set the outer washer in place. Lock button Front cover 6. Insert the hex bolt. 7. Hold the spindle lock button down. This pre- vents the blade from rotating. 8. Tighten the hex bolt securely with the provid- ed hex wrench. Store the hex wrench. NOTE: Keep the hex wrench in the storage slot on the tool’s body when not using it.
Inner washer Place the inner washer with cut-out facing you. Retracting handle Outer washer Place the protrusion of the outer washer into the position of the washer. Spindle lock button Lower guard Loosen Hex bolt Tighten Fig. 6 Using the Tool 1.
Cutting depth adjustment Handle • Remove battery pack. Switch lock lever • Loosen the depth adjustment nut and adjust the cutting depth, using the graduations on the Front grip lower guard to gauge the depth. Once finished adjusting the depth, tighten the depth adjust- ment nut securely.
Collecting Dust WARNING * Before cutting metal materials, always empty the dust case, open the front cover and remove the dust. • Use the tool with the flammable materials in the dust case to cut metal materials may result in fire. * When cutting metal materials, always use the tool with the dust case attached.
Excessive (complete) discharging of lithium ion Caution : DO NOT STARE INTO BEAM. batteries shortens their service life dramatically. Use of controls or adjustments or performance The tool includes a battery protection feature of procedures other than those specified herein designed to prevent excessive discharging of may result in hazardous radiation exposure.
Cutting thin or corrugated materials; Cut thin and corrugated materials at least 25 mm (1") from the edge of the workpiece to avoid injury or damage to the tool caused by thin strips of metal being pulled into the upper guard.
2. Make sure the blade stops. Even though your tool has a brake, before setting the tool down, make sure the blade has come to a complete stop and the lower guard has closed. 3. Do not use if anything seem unusual. Remove battery pack immediately. If the tool body becomes very hot, or does not work properly, remove the battery pack and do not use.
[Battery Charger] • Charging will not start if the battery pack is warm (for example, immediately after Charging heavy-duty operation). The orange standby lamp will be flashing CAUTION: until the battery cools down. Charging will then begin automatically. • If the temperature of the battery pack falls 4.
Lamp Indications Charging is completed. (Full charge.) Battery is approximately 80% charged. Now charging Charger is plugged into the AC outlet. Ready to charge. Charging Status Lamp (Green) (Orange) Left: green Right: orange will be displayed. Battery pack is cool. The battery pack is being charged slowly to reduce the load on the battery.
Carbide-tipped Blade for Thin Metal (Optional rized service center. Always insist on genuine accessory) Panasonic replacement parts. • EY9PM13D For cutting unhardened thin ferrous thin material Cleaning Tool that clean cutting edge required...
. SPECIFICATIONS Motor voltage 14.4 V DC Blade speed 3600 min (rpm) Blade size Outside diameter 135 mm Arbor size 20 mm Maximum cutting depth 0 – 46 mm (φ135 mm blade) Overall length 329 mm Weight (with battery pack) 2.65 kg Noise See the included sheet.
A replacement fuse cover can be purchased from your local Panasonic Dealer. Fuse Cover IF THE FITTED MOULDED PLUG IS UNSUITABLE SOCKET...