Sanyo PLC-XU116 Service Manual page 45

Electrical Adjustments
Group/
Item Name
Item
26 Eco Fan3 Min
27 Eco Fan3 Max
28 Eco Fan4 Min
29 Eco Fan4 Max
Group
Fan Start/cooling Setting
255
0 Fan1 Initial Volt
1 Fan2 Initial Volt
2 Fan3 Initial Volt
3 Not used
4 Fan1 Cooling Speed
5 Fan2 Cooling Speed
6 Fan3 Cooling Speed
7 Not used
8 Cooling Time L1
9 Cooling Time L2
10 Temp Error Cooling Time
11 OnStart Cooling Start
Threshold
12 After shutdown cooling
Group
Fan lamp Voltage down Setting
256
0 Lamp Voltage
1 Lamp Vol Threshold
2 Fan1 Speed Gain
3 Fan2 Speed Gain
4 Fan3 Speed Gain
5 Not used
Group
Fan dimmer Setting
257
Dimmer Average Check
0
Period
1 Dimmer Average
2 Last Voltage Difference
3 Voltate Difference Goal
Group
Fan Ic temp for Netowrk model
258
Standby Cooling Check
0
Cycle
Standby Cooling Start
1
Threshold
2 Standby Cooling Enable
Group
Auto calibration (commn) * Auto calibration
260
0 Execute Calibration
1 Loop Count
2 Auto Status
3 AutoWait
4 CHECK -Tolelance
Group
Auto calibration (rGB)
261
0 OFFSET AREA H START
1 OFFSET AREA V START
2 GAIN AREA H START
3 GAIN AREA V START
Function
Fan voltage value at Eco (unit: 0.1V)
Fan Start Voltage (0.1V)
Fan Voltage at Power Off (0.1V)
Cooling Time stting at Fan Mode L1 (x
30 sec)
1: 30, 3: 90, 15: 450 sec.
Cooling Time stting at Fan Mode L2 (x
30 sec)
1: 30, 3: 90, 15: 450 sec.
Cooling Time setting at Temp Erro (x
30 sec)
Cooling after shutdown (0: No, 1: Yes)
Current Lamp Voltage (0.1V)(Read
only)
Threshold to judge Lamp Voltage
Down ( V×10)
Additional Fan Speed of Min at Lamp
Voltage Down (unit: 0.1V)
Dimmer Avarage measurement Time
(0:10sec, 1:30sec, 2:6sec,
90sec...10:300sec)
Dimmer Avarage Value (Read only)
Temp A check cycle at Standby
Cooling start threshold temp A
Cooling in standby Enable
Maximum Execution Times
(OFFSET->GAIN)
Result of Auto-Calibration (Last
Memory)
Wait Value for each setting
Torelance of OFFSET
Black Level Acquiring Area H-Start
Position
Black Level Acquiring Area V-Start
Position
White Level Acquiring Area H-Start
Position
White Level Acquiring Area V-Start
Position
Initial
53 53 58 58
53 53 63 63
9999 9999
9999 9999
70
70
70
9999
130
130
130
9999
2
3
3
38
1
-
9999
1
-
-
5
46
1
0
10
0
1
2
975
500
25
500
-45-
range Note
0-255
0-255
-
-
0-255
0-255
0-255
-
0-255
0-255
0-255
-
1-15
1-15
1-15
0-100
0-1
0-255
30-90
0-255
0-255
0-255
0-255
0-10
Executes Auto-Calibration when
0 - 1 changiing the Value (PC White
100%)
1 - 30
0: OK, 1: Adjusting,9: Error *
0 / 1 / 9
ReadOnly
1 - 20
1 - 255
0 - 1000
0 - 1000
0 - 1000
0 - 1000