Innovative Hearth Products
Superior
DRT35 See Through and Peninsula Direct Vent Gas Fireplace
TM
TABLE OF CONTENTS
Packaging .........................................Page 4
Requirements for the
Location ............................................Page 7
Maintenance ......................................Page 50
Warranty ...........................................Page 69
Please read and understand these
instructions before beginning your
installation.
4
PACKAGING
The assembled vented gas fireplace heater is
packaged with:
1 - the logs are packaged in a carton located
within the firebox.
2 - one plastic bag of glowing embers is located
in the bottom compartment.
3 - one envelope containing the literature
package which consists of Installation In-
structions and Care and Operations manual
(IICO) with warning labels and warranty;
envelope is located in the bottom compart-
ment.
4 - one vent restrictor to be applied as shown on
page 14; restrictor is taped to the envelope.
5 - two hoods on see through units and three
hoods on peninsula fireplaces
6 - top standoffs taped to top of unit
7 - front face assemblies with barriers.
NOTE:
• If the barrier becomes dam-
aged, the barrier shall be re-
placed with the manufacturer's
barrier for this appliance.
• For use with barrier(s) Part
No(s). J7424 (ST Models) and
J7424 and J7425 (PF Models).
INTRODUCTION
The Millivolt appliances have a millivolt gas
control valve with piezo ignition system. If any
optional accessories that will require electrical
power are to be installed, the electrical power
must be provided at the time of appliance
installation.
The Electronic appliances are designed to op-
erate on natural or propane gas. An electronic
intermittent pilot ignition system provides safe,
efficient operation. External electrical power is
required to operate these units.
These vented gas fireplace heaters are sealed
combustion, air-circulating gas fireplaces de-
signed for residential applications.
Approved Vent Components - These fireplaces
are designed, tested and listed for operation
and installation with the following vent com-
ponents only:
•
Secure Vent™ Direct-Vent System Compo-
nents manufactured by Security Chimneys
International,
•
Secure Flex™ Flexible Vent Components
manufactured by Security Chimneys Inter-
national and
•
Z-FLEX™ Model GA Venting Systems listed
to UL1777 and ULCS635 manufactured by
Flexmaster Canada Limited.
Use only the correct size venting (4-1/2" inner
and 7-1/2" outer).
These approved vent system components are
labeled for identification. DO NOT use any
other manufacturer's vent components with
these appliances.
Installation and Operation Instructions
900300-00, 02/2015
GENERAL INFORMATION
WARNING
Young children should be care-
fully supervised when they are
in the same room as the appli-
ance. Toddlers, young children
and others may be susceptible
to accidental contact burns. A
physical barrier is recommended
if there are at risk individuals in
the house. To restrict access to
a fireplace or stove, install an
adjustable safety gate to keep
toddlers, young children and
other at risk individuals out of
the room and away from hot
surfaces.
AVERTISSEMENT
Les jeunes enfants devraient être
surveillés étroitement lorsqu'ils
se trouvent dans la même pièce
que l'appareil. Les tout petits,
les jeunes enfants ou les adultes
peuvent subir des brûlures s'ils
viennent en contact avec la sur-
face chaude. Il est recommandé
d'installer une barrière physique
si des personnes à risques habi-
tent la maison. Pour empêcher
l'accès à un foyer ou à un poêle,
installez une barrière de sécu-
rité; cette mesure empêchera les
tout petits, les jeunes enfants et
toute autre personne à risque
d'avoir accès à la pièce et aux
surfaces chaudes.
Children and adults should be alerted to the
hazards of high surface temperature and
should stay away to avoid burns or clothing
ignition.
Les enfants et les adultes devraient être infor-
més des dangers que posent les températures
de surface élevées et se tenir à distance afin
d'éviter des brûlures ou que leurs vêtements
ne s'enflamment.
DO NOT ATTEMPT TO ALTER OR MODIFY
THE CONSTRUCTION OF THE APPLIANCE OR
ITS COMPONENTS. ANY MODIFICATION OR
ALTERATION MAY VOID THE WARRANTY, CER-
TIFICATION AND LISTINGS OF THIS UNIT.