Use Of The Remote Controller - Carrier 42 VKG Owner's Manual

42 VKG

Use of the remote controller

Start/stop
(button B)
When the air conditioner is not in operation, the controller readout
will display the time of day only (in case other symbols are lit, turn
controller off by pressing button B
Press button B to start the air conditioner; indicator N on the
unit will appear and be illuminated.
All selected and memorized functions will light up and appear; the
unit will operate according to the functions selected.
If the unit does not acknowledge the starting signal by emitting a
sound ("beep") and indicator N does not light up, it is necessary to
turn the controller off by pressing button B
operation.
Press button B to stop the air conditioner.
All indicators on the unit will go out, and controller will display only
the current time.
If the unit does not stop, turn the controller on (by pressing button
B ) and repeat the operation.
In some special operating conditions the fan will continue to run
for 30 sec. after the unit stops; indicator P on the unit will lighten.
If button B (air conditioner starting) is pressed too soon after a
stop, the compressor will not start for 3 minutes due to the
inherent protection against frequent compressor cycling; in this
case indicator P on the unit will also light up.
The unit will only emit a "beep", when the signals are received
correctly.
Timer mode on/off
(button C)
Press this button if you want the air conditioner to operate in the
timer mode according to the time programs selected with button
G .
If this function is on, indicator Q on the unit is lit.
After a power failure, indicator Q will flash and the unit will run in
the last operating condition before the power cut.
Power failures will deactivate the Timer mode: to reactivate the
Timer mode, press button C
Selection of the operating mode
(button D)
With this button the operating mode of the air conditioner can be
selected.
Different options are available depending on the unit model.
By repeatedly pressing this button the available modes will be
selected in sequence and the relevant symbols will appear on the
display, while the unit will acknowledge signal receipt with a
confirming beep.
Symbol on display
Cooling with dehumidification.
Heating (where available).
Automatic mode.
The air conditioner will automatically switch from heating
(where available) to cooling and vice versa in order to
maintain the selected temperature.
Dehumidification only.
The air conditioner extracts moisture from the air without
sensibly changing the room temperature.
Ventilation (fan only).
).
and then repeat the
twice.
Setting desired temperature
UP
(button E)
DOWN
(button F)
Pressing the UP (E ) and DOWN (F
decrease the temperature set from the previously set value. The
unit will confirm signal receipt with a beep, and the value of the set
temperature on the display will change accordingly.
The temperature can be set between 18°C and 29°C at 1 degree
intervals.
In the cooling mode, if the temperature selected is higher than the
room temperature, the unit will not start; the same applies for the
heating mode, if the selected temperature is lower than the room
temperature.
Setting the timer programs
(button G)
By pressing button G it is possible to choose one of the
following programs in sequence:
Symbol on display
No symbol Continuous operation (timer off)
Start time program
Stop time program
Combined program: unit will automatically cycle on and off
as programmed
Set start time
Press button G until the symbol indicating unit start program
appears on the display under the word TIMER.
• The time appearing on display shows the starting hour
previously programmed:
• You can set your personalized new start time by pressing buttons
H and I until the desired time appears. Each press of the
button will change the time up or down by 15 min. between 0:00
and 23:45.
Press button C to confirm your selection: indicator Q on the
unit will light up and the air conditioner is ready to start at the
selected time. If the unit is in operation when you send your
confirmation by pressing button C
restart at the time now programmed.
Set stop time
Press button G until the symbol indicating the unit stop program
appears on the display under the word TIMER.
The time appearing on the display shows the stop time previously
programmed; you can now set your personalized new stop time by
proceeding as for the start time.
If the unit is turned off when you send your program confirmation by
pressing button C , it will start up, and then turn off at the time
now programmed.
E N G L I S H
) buttons will increase or
, it will turn off and
GB - 7