Do you have a question about the 610 and is the answer not in the manual?
Questions and answers
Dorothy Holmes
April 23, 2025
I was using my slicer to cut frozen bread and it just stop cutting mid slice. I suspect I may need to replace the fuse. Any other possibilities? Is there a reset button I should be looking for?
1 comments:
Mr. Anderson
May 11, 2025
A Chef's Choice 610 slicer could stop cutting mid-slice if the fuse blows. The slicer uses a Slo-Blo type fuse rated at 1.25A and 250V, located underneath the motor housing. There is no mention of a reset button in the provided information.
This answer is automatically generated
Tammy Bushman
March 29, 2025
Can I?
Get a manual in the mail On how to use my meat slicer 610 ?
1 comments:
Mr. Anderson
March 29, 2025
You can obtain a manual for the Chef's Choice 610 meat slicer by downloading it from an online archive, where the "Chef'sChoice 610 Use and Care Manual" is available for free.
This answer is automatically generated
anthony pastore
March 21, 2025
where can i buy a retaining screw cap for a 610 chefs choice slicer.
1 comments:
anthony pastore
March 21, 2025
@anthony pastore
Bill Boyd
March 1, 2025
The thickness control knob doesn't lock the thickness guide plate in position, so I have to hold the guide plate pushing it toward the meat. Is this normal?
1 comments:
Mr. Anderson
March 1, 2025
No, it is not normal. The thickness control knob should lock the thickness guide plate in position when properly aligned. To secure it, the knob must be turned counterclockwise to the "0" position after pushing the guide plate fully into place. If the plate is not locking, it may not be seated correctly or the knob may not be turned to the correct position.
This answer is automatically generated
Alice Finlinson
February 2, 2025
can we purchase a fuse from you
1 comments:
Mr. Anderson
February 10, 2025
Yes, satisfactory replacement fuses for the Chef's Choice 610 are available. Compatible fuses include Hollyland 50T, LittelFuse (Model 2181.25), and Bussman GDCS505. These are Slo-Blo type fuses rated at 1.25A and 250V.
This answer is automatically generated
David Tejada
June 16, 2025
Where can I get a Food Carriage for my 610
Frank Amity
April 24, 2025
once installed the blade is wobbling. Is there a spring that holds tension against the gear, or does the gear need replaced
Russell Spurrell
March 29, 2025
I would like to know how to sharpen the blade on a 610 slicer. Thanks
Need help?
Do you have a question about the 610 and is the answer not in the manual?
Questions and answers
I was using my slicer to cut frozen bread and it just stop cutting mid slice. I suspect I may need to replace the fuse. Any other possibilities? Is there a reset button I should be looking for?
A Chef's Choice 610 slicer could stop cutting mid-slice if the fuse blows. The slicer uses a Slo-Blo type fuse rated at 1.25A and 250V, located underneath the motor housing. There is no mention of a reset button in the provided information.
This answer is automatically generated
Can I? Get a manual in the mail On how to use my meat slicer 610 ?
You can obtain a manual for the Chef's Choice 610 meat slicer by downloading it from an online archive, where the "Chef'sChoice 610 Use and Care Manual" is available for free.
This answer is automatically generated
where can i buy a retaining screw cap for a 610 chefs choice slicer.
@anthony pastore
The thickness control knob doesn't lock the thickness guide plate in position, so I have to hold the guide plate pushing it toward the meat. Is this normal?
No, it is not normal. The thickness control knob should lock the thickness guide plate in position when properly aligned. To secure it, the knob must be turned counterclockwise to the "0" position after pushing the guide plate fully into place. If the plate is not locking, it may not be seated correctly or the knob may not be turned to the correct position.
This answer is automatically generated
can we purchase a fuse from you
Yes, satisfactory replacement fuses for the Chef's Choice 610 are available. Compatible fuses include Hollyland 50T, LittelFuse (Model 2181.25), and Bussman GDCS505. These are Slo-Blo type fuses rated at 1.25A and 250V.
This answer is automatically generated
Where can I get a Food Carriage for my 610
once installed the blade is wobbling. Is there a spring that holds tension against the gear, or does the gear need replaced
I would like to know how to sharpen the blade on a 610 slicer. Thanks