Show System - Cisco Catalyst 4000 series Hardware Troubleshoot

Module 2 : 34−port Router Switch Card
Status: (. = Pass, F = Fail, U = Unknown)
Eeprom: .
CX1000 Regs:
Ports 3−11
Ports 28−34 : .
CX1000 Sram:
Ports 3−11
Ports 28−34 : .
10/100Base−TX Loopback Status:
Ports 3
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
.
−−−−−−−−−−−−−−−−−−−−−−−
.
1000Base−X Loopback Status:
Ports 1
−−−−−
.
Router CPU board Status:
Module 3 : 24−port 10/100/1000 Ethernet
Status: (. = Pass, F = Fail, U = Unknown)
Eeprom: .
Lemans Regs:
Ports 1−4
Ports 13−16 : .
Lemans SRAM:
Ports 1−4
Ports 13−16 : .
10/100/1000Base−TX Loopback Status:
Ports 1
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
.
Module 5 : 6−port 1000BaseX Ethernet
Status: (. = Pass, F = Fail, U = Unknown)
Eeprom: .
Alpheratz: .
1000BaseX Loopback Status:
Ports
−−−−−−−−−−−−−−−−−−−−−−−
Cat4000−c> (enable)

show system

This command displays system information. The status fields relate to the various LEDs on the system
components. Take note of the uptime or how long the switch has been up and running. This would be useful
information to know in the event of a switch crash. Refer to the show system command for more information.
Cat4000−c> (enable) show system
PS1−Status PS2−Status PS3−Status PEM Installed PEM Powered
−−−−−−−−−− −−−−−−−−−− −−−−−−−−−− −−−−−−−−−−−−− −−−−−−−−−−−
OK
Fan−Status Temp−Alarm sys−status Uptime d,h:m:s Logout
−−−−−−−−−− −−−−−−−−−− −−−−−−−−−− −−−−−−−−−−−−−− −−−−−−−−−
OK
: . Ports 12−19
: . Ports 12−19
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
. . . . . .
27 28 29 30 31 32 33 34
. . . . . .
2
.
: . Ports 5−8
Ports 17−20 : .
: . Ports 5−8
Ports 17−20 : .
2 3 4 5 6 7
. . . . . .
1 2 3 4 5 6
. . . . . .
OK none
off OK
: . Ports 20−27 : .
: . Ports 20−27 : .
. . . . . . .
.
: . Ports 9−12
Ports 21−24 : .
: . Ports 9−12
Ports 21−24 : .
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
. . . . . . .
no no
28,15:10:39 20 min
. . . . . . .
: .
: .
. . . . . . .
. . .
. . .