2. During repair or tests, do not view laser beam for 10 seconds or longer. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS AVIC-Z110BT/XN/UC...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. AVIC-Z110BT/XN/UC...
2) After 40 seconds, turn off the BUP line. Note: Navi software required approximately 40 seconds for storing the data after ACC OFF. For your information, after the BUP current is less than 380 mA, you can turn off BUP line. AVIC-Z110BT/XN/UC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. AVIC-Z110BT/XN/UC...
DVD Format/Logo Licensing Corporation. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners.
Item to be checked regarding video Item to be checked regarding audio Block-noise Distortion Horizontal noise Noise Dot noise Volume too low Disturbed image (video jumpiness) Volume too high Too dark Volume fluctuating Too bright Sound interrupted Mottled color AVIC-Z110BT/XN/UC...
Unit Name Navi Unit Unit Number CWN3935 Unit Name Monitor Unit Unit Number CWN3988 Unit Name Keyboard Unit Unit Number EXX1060 Unit Name PCB Unit(Service) Unit Number YWX5009 Unit Name DVD Core Unit Unit Number Unit Name Connect PCB AVIC-Z110BT/XN/UC...
Do not use GGD1632 and GGD1633 at the same time. The picture will be distorted if you use both of them. NAVI UNIT GGD1632 MONITOR UNIT NAVI UNIT GGD1633 AUDIO UNIT GGD1631 AUDIO UNIT DVD CORE UNIT GGD1222 GGD1609 DRIVE UNIT GGD1188 TUNER IF UNIT AVIC-Z110BT/XN/UC...
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools DVD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Portions to be cleaned Cleaning tools Fans Cleaning paper : GED-008 AVIC-Z110BT/XN/UC...
AUDIO UNIT (PS/IF SECTION) CC UNIT (NAND PART) CC UNIT (VIDEO DEC./T-CON/ AUDIO UNIT (SYSCOM SECTION) AUDIO UNIT (AV SECTION) CODE ASS'Y PREOUT BtoB TERMINALS CDP1194 Wired Remote Jack JA5202 JA2880 CN2512 CN2101 CN511 RDS-TMC TUNER (AU only) TUNER IF UNIT CXE2176- AVIC-Z110BT/XN/UC...
Page 21
CODE ASS'Y NAVI UNIT (IF PART INTERNAL) TOUCH PANEL KEYBOARD UNIT CSX1148- iPod Connerctor JA5202 JA5251 CN5251 CN5001 CODE ASS'Y MIC ASS'Y CDP1195 CPM1083 CXM1394 4PIN JACK 17PIN PLUG DRIVE MECHA USB-A UNIT JUNCTION SOCKET CXE1522- PCB UNIT (SERVICE) AVIC-Z110BT/XN/UC...
MAX 45 mA 2 mA TYP 32 mA 8 mA SWVDD 5.5 mA -> 4 mA 2SA1577 SWVDD33 ACCPW5 TO NAVI UNIT IR REMOTE(UW5/AU) RS-750 SWAC33 2SA1577 SWACC33 2 mA EEPROM SWACPW5 DualZone MUTE RDS DETECT (EU5/UC/AU) 2SA1576 MOTVDD UMF21N ACCPW AVIC-Z110BT/XN/UC...
Page 35
Power Supply This block diffiers with the region of destination. RESET IC RESET Circuit RDS Circuit(EU5/UW5/UC) BD5229FVE UMD3N UMH1N*2 2 mA TE(UW5/AU) 2 mA TELMUTECircuit 2SA1576A AVIC-Z110BT/XN/UC...
Page 36
290 mA max 5 mA 5 mA For Audio AV4.3(4.2 V) 436.3 mA/3.141 W over NJM2125F AU84(Reg) (Center Voltage for Audio) 101.3 mA AU8.4 8.4 V NJM2388F84 SYSPW5 (AU8) For Auto TO NAVI UNIT ANT+B(SW) TPD1018F 300 mA(MAX) ANTON5 AVIC-Z110BT/XN/UC...
Page 37
VIDEO LEVEL SHIFT(2 -> 1) 2SC4081(RS)*2 15 mA typ:9.6 mA CAPTAIN7 max:13 mA typ:56 mA max:71 mA 9 mA GUIDE MIX NJM2747V LS1 LPF NJM2904 MUTE Circuit 5.7 mA Guide, P-Amp. UMD3N *3 1.6 mA max NAVI ISOLATOR BA4558RFVM AVIC-Z110BT/XN/UC...
Page 38
TO FLAP DRIV SOC1.5 A CEK1262- MOTOR 7.5 V/6.5 V MOTOR DRIVER MOTOR 0/1 2SB1260(Q) SA1797(Q) MOTPWR5, MOTPW 75 mA/250 mW SWBUP(EU5/UC/AU) TPD1018F RDSSNS MSN_RST:UC TMC-MSN-ON5:EU5/AU HOLD BUP PKB SNS IO33 NKBUP 10 000[uF]/16[V] FROM NAVI UNIT TO NAVI UNIT AVIC-Z110BT/XN/UC...
Page 39
TO NAVI UNIT for ILM power supply TO FLAP DRIVER UNIT Max:200 mA (Lock 600 mA) RIVER Rush MAX 1 030 mA AVIC-Z110BT/XN/UC...
Page 40
ASENB0 2SA1576A DTC114EUA ASENB05 MAX:360 mA ILMV CEK1254 MAX:100 mA FAN POWER SUPPLY CXN1394-A 2SD1760F5(R) 2SA1587(GRBL) FANUP,FANCONT,FANON CEK1254 PWR VI SW MAX:232 mA 2SD1760F5 MONITOR UNIT UMF23N SWACPW5 1.25 A CEK1255 PWR BL SW MAX:480 mA 2SB1184F5 DTC143EUA SWACPW5 AVIC-Z110BT/XN/UC...
Page 42
39 k NJM13403V CCA25 39 k 2.9 V BH29NB1WHFV-TR DTV3 MAX:42.1 mA DTV5 1.8 V BU18TA2WNVX DTV5 1.2 V BH12PB1WHFV DTV3 MAX:900 mA CCD3 CKS5701A R1515H080B MAX:25 mA Logic IC TC7SH04FUS1 DTV3 MAX:12[mA] CCDIO3 MAX:24 mA R232C Driver UPD4721GSS1 AVIC-Z110BT/XN/UC...
Page 43
BU18TA2WNVX VDDC 1.2 V MAX:13.2 mA BH12PB1WHFV VCCA 3.3 V <-> 1.8 V MAX:25 mA TC7WPB9306FK VCCB MAX:25 mA 3.3 V <-> 1.8 V CKS5701A VCCA MAX:3 mA TC7MP3245FTG c IC SH04FUS1 VCCB MAX:12 mA NOT MOUNT NOT MOUNT AVIC-Z110BT/XN/UC...
Page 44
CONNECTION HN1B04FU(Y) TC7SET08FUS1 NOT MOUNT SECCONT,ASENS 3.0 ± 0.1 V VDD5 GYRO Sensor 3.0 V ± CSX1147 BH30NB1WHFV-TR TYP:1. PLL_ON G Sensor 3.0 V(2 CSX1149 TYP:0. MAX:0 3.0 V(2 ADS7828E TYP:0. MAX:0 3.0 V(2 Temp Sensor TYP:0. S-58LM20A-N4 MAX:0 AVIC-Z110BT/XN/UC...
Page 45
MAX:1 160[mA] CCD5 CCA3 MAX:54mA MAX:26[mA] VDD5 3.0 V ± 0.15 V TYP:1.7 mA 3.0 V(2.4 V-3.6 V) TYP:0.68 mA MAX:0.85 mA 3.0 V(2.7 V-3.6 V) TYP:0.225 mA MAX:0.32 mA 3.0 V(2.7 V-5.5 V) TYP:0.004 5 mA MAX:0.006 mA AVIC-Z110BT/XN/UC...
Page 46
MAX:1 549.1 + @ mA 2.5 ± 1% MAX:105 mA Pc:84 mW LCD25 LCD25 Sequence generation BU25TA2WNVX 1.5 ± 0.025 V MAX:120 mA RST1 PRE_ON Pc:216 mW 3.0 V LCD15 LCD15 BU15TA2WNVX RST2 IO_ON 3.5 V RST3 PLL_ON 4.4 V AVIC-Z110BT/XN/UC...
Page 47
1.5 V ± 0.2 V 1.5 V LCD25 TC90192XBG MAX:70 mA MAX:105 mA MAX:120 mA 3.3 V MAX:120 mA Pc:216 mW SRAM(1M) 3.3 V(2.2 V-3.6 V) 3.3 V LCD15 CY62126EV30LL55BVE MAX:20 mA BUP3 iPod 3.3 V(1.8 V-3.6 V) 3.3 V certification MAX:10.0 mA AVIC-Z110BT/XN/UC...
Page 48
(for SiRFprima) 1.8 ± 0.025 V MAX:76 mA Pc:114 mW VD18 VD18 BU18TA2WNVX IO_ON VA18 VA18 BU18TA2WNVX IO_ON TYP:11 mA 1.8 ± 0.025 V Pc:16.5 mW CP18 CP18 BU18TA2WNVX 3.3 ± 1% MAX:18 mA Pc:30.6 mW GPS33 BU33TA2WNVX GPS_SAMPLE_C AVIC-Z110BT/XN/UC...
Page 49
TYP:45 mA MAX:70 mA 3.3 V GPS-RF MAX:18 mA (2.6 V-2.85 V-3.6 V) GPS33 GRF3i+ Pc:30.6 mW TYP:16.0 mA(2.85 V) 3.3 V MAX:18.0 mA(2.85 V) PS_SAMPLE_CLK GPS Antenna TYP:19 mA power supply MAX:30 mA 3.3 V USB jig ETHER jig AVIC-Z110BT/XN/UC...
Page 50
300 CK5050+ LED Backlight Actual survey value: DD Converter typ 120 (14 V -> 27 V) CWX3913-A max 130 BD8113FM Actual survey value:12.94 Actual survey value:12.94 typ 18 typ 18 DAC to BT CCA5 max 27 AK4388VT max 27 AVIC-Z110BT/XN/UC...
Perform lens Is it OK? cleaned? cleaning Replace the PICK UP Check point: Error rate check Error rate check PICK UP Perform lens Is it OK? cleaned? cleaning Replace the PICK UP Ckeck parts Finished other than PICK UP AVIC-Z110BT/XN/UC...
Page 53
60 - 390 (mV) 10 - 65 (mA) Expansion NO. Disc Check Point Threshold Remarks: LD current TCD-782 CDLD1-VCC5_3 60 - 360 (mV) 10 - 60 (mA) Expansion Notes: Please pay attention to the laser diode damage by static electricity. AVIC-Z110BT/XN/UC...
Page 54
GGV1025 ID: 40000 1.000E-03 less than GGV1025 ID: 200000 1.000E-03 less than TCD-782 ID: HOME Position 2.500E-03 Test mode display will not appear on the display of this product. Connect the rear monitor output to a monitor. AVIC-Z110BT/XN/UC...
Page 56
<Check> Check the voltage at the “STANBY” test point while the power is on. Use the “DGND1” test point at the reference. Specification value Check point Module No. Unit VCC33 V- STANBY-DGND1 0.6 V or more Side A STANBY Fig 1.1: STANBY check point AVIC-Z110BT/XN/UC...
Page 58
<Check> Check the voltage at the “XRES” test point while the power is on. Use the “DGND1” test point at the reference. Check point Module No. Specification value Unit VCC33 × 1 XRES-DGND1 0.7 or more Side A DGND1 NRES Fig 3.1: RESET check point AVIC-Z110BT/XN/UC...
Page 59
<Check> Check the voltage at the “VSENS” test point while the power is on. Use the “DGND1” test point at the reference. Specification value Check point Module No. Unit 1 VSENS - DGND1 0.95 - 1.07 VD8 = 8.0 ± 0.4 V Side A VSENS DGND1 Fig 4.2: VSENS check point AVIC-Z110BT/XN/UC...
Page 60
Specification value Check point Module No. Unit 27 MHz 2 IC1501 169pin ± 50 ppm Specification value Fig 5.2: Clock specification value Side A IC1501 158pin DGND1 Fig 5.3: 27 MHz check point AVIC-Z110BT/XN/UC...
Page 61
Be careful as XCSM, XWE, XCAS and XRAS of IC1480 are called differently in IC1501, namely NCSM, NWE, NCAS, NRAS. IC1501 MA0 - 11 1480 DV5U MDQ0 - 15 SDRAM XWE(NWE) XCAS(NCAS) XRAS(NRAS) XCSM(NCSM) DQM0 DQM1 Fig 6.1: SDRAM I/F AVIC-Z110BT/XN/UC...
Page 63
Side B Check point 1 (IC1480) Side A Check point 2 (IC1501) Fig 6.2: SDRAM I/F check point AVIC-Z110BT/XN/UC...
Page 64
Check point Module No. Specification value Unit VD8_1 - PGND3 8.0 ± 0.4 VD - PGND3 8.0 ± 0.4 VCC5_1- AGND1 5.0 ± 0.1 Side A AGND3 VCC5_ 1 PGND1 VD8_ 1 PGND3 Fig 7.2: VD8, VCC5 voltage check points AVIC-Z110BT/XN/UC...
Page 65
Check with PGND and GNDAU being the reference. Check point Module No. Specification value Unit VD - PGND_3 8.0 ± 0.4 AVCC5 - GNDAU1 5.0 ± 0.1 Side A AVCC5 PGND3 GNDAU1 Fig 8.2: VD8, AVCC5 voltage check points AVIC-Z110BT/XN/UC...
Page 66
Specification value 3 36.864 0 MHz ± 300 ppm DACCK 2.0 V~VCC33 V DGND~0.8 V DACCK 2.0 V~VCC33 V DGND~0.8 V 33.868 8 MHz ± 300 ppm Specification value 1 Specification Specification value 2 value 3 Fig 9.2: Clock specification value AVIC-Z110BT/XN/UC...
Page 67
Side B Check point 1 (DACCK stylus) Side A Check point 2 (IC1501 148 pin) DGND2 Fig 9.3: 27 MHz, DACCLK check point AVIC-Z110BT/XN/UC...
Page 68
Waveform 1 SRCK VCC33 V-0.6 V or higher 0.4 V or lower Waveform 2 LRCK VCC33 V-0.6 V or higher 0.4 V or lower Waveform 3 Specification value 2 Specification value 1 Fig 10.2: Serial 3 lines specification value AVIC-Z110BT/XN/UC...
Page 69
Side A DGND2 ADOUT LRCK Side B SRCK Fig 10.3: Serial 3 lines check points AVIC-Z110BT/XN/UC...
Page 70
GNDAU1 Fig 10.5: Analog audio out check point Check with DGND being the reference. Specification value 2 Check point 1 (stylus) Specification value 1 Reference waveform 6 IEC VCC33 V-0.6 V or higher 0.4 V or lower Waveform 5 AVIC-Z110BT/XN/UC...
Page 71
Side A IEC DGND2 Fig 10.6: Digital audio signal (IECOUT) check point AVIC-Z110BT/XN/UC...
Page 72
In case of NG, check the applicable line, the periphery of the major components in the drawing above, soldering of the peripheral components and defective components. PEAK Reference COMPOSITE signal value Color burst Pedestal level BOTTOM Horizontal sync signal Fig 11.2: Waveform for the case of composite white 100% output AVIC-Z110BT/XN/UC...
Page 73
Side A COMPOSITE GNDV Fig 11.3: VIDEO signal check point AVIC-Z110BT/XN/UC...
Page 74
(Refer to the FE test mode for the method of displaying the LD energizing time.) 2.If the second digit from the left of the energizing time display is showing E, such as “ E ”, it means that the flash memory has reached its life. Example: 0E000BB8 AVIC-Z110BT/XN/UC...
Page 75
In case of NG, check the applicable line, periphery of IC1501, soldering of the peripheral components and defective components. Specification value Check point Module No. Unit 48 MHz 2 IC1501 50pin-DGND1 ± 50 ppm Specification value Fig 13.2: Clock specification value AVIC-Z110BT/XN/UC...
Page 76
Side A IC1501 50pin DGND1 Fig 13.3: 48 MHz check point AVIC-Z110BT/XN/UC...
Page 77
1.USB Memory: Play a song from USB memory and check D+ and D- with the DGND standards. 2.iPod: Connect iPod and check CP_RESET, SDA and SCL with the DGND standards until the pioneer log appears. Play a song from iPod and check D+/D- with the DGND standards.
Page 78
Side A SDATA CP_ RESET SCLOCK DGND2 AVIC-Z110BT/XN/UC...
CBW and CSW forwarding error ERROR-02-D1 CBW and CSW forwarding error Audio class band securing failure ERROR-02-D8 Audio class band securing failure Audio class FS setting failure ERROR-02-D9 Audio class FS setting failure Undefined Error ERROR-FF-FF Undefined error AVIC-Z110BT/XN/UC...
Page 83
*5 AWM (Audio WaterMark): Electronic watermark. Information on the copyright owner or CCI (copy control information) are recorded so that illegally copied discs can be identified. *6 Notice as an error status will not be given *7 CPRM(Content Protection for Recordable Media) : A copyright protection technique for digital contents used for re-writable DVD or memory card. (DVD-VR model only) AVIC-Z110BT/XN/UC...
3. Release [HOME] key. Start-up by SD card. 1. Download GGS1080 from the Service Site. 2. Decompress the file. 3. Copy the decompressed file to the SD card root. 4. Insert the SD card to the product and turn ACC on. AVIC-Z110BT/XN/UC...
Page 86
Test of Hard Key. Key Test Status display of Input Port. Port Test Status display/changeover of Output Port. Display drive information, disc scanning Drive Maintenance (verification of volume). File operation and file deletion. File Maintenance Dumping display of file contents. AVIC-Z110BT/XN/UC...
Page 87
Data readout of NAND FLASH. NAND Test Writing data or file into NAND FLASH. Execution of User Area clearing. USER'S AREA OF FLASH CLEAR Guiding Audio Line confirmation by the replay of Audio Play Test audio file. Display various test images. Image Test AVIC-Z110BT/XN/UC...
Page 88
Display image of back camera on navigation BACK CAMERA TEST screen. Check wire connecting status of 3 color signals RGB KEY ILLMINATION TEST for RGB key illumination. Confirming flap close and displaying RPS value. MechaClose Position Confirmation Display product information. PRODUCT INFORMATION AVIC-Z110BT/XN/UC...
Page 89
[NO_SET]: No information SYSTEM uCOM Version of startup program for [ *.****** ]: Value of Version BOOT PROGRAM system microcomputer [NO_SET]: No information NAND CID Firmware ID of NAND Flash [ *.****** ]: ID value [ GET_NG ]: Acquisition failed AVIC-Z110BT/XN/UC...
Page 90
Region Code of DVD ]: Europe / Normal Region Code ]: North America / Normal Region Code ]: Russia / Normal Region Code ]: Australia / Normal region Code * Values other than above are abnormal values. [ NO_SET ]: No information AVIC-Z110BT/XN/UC...
Page 91
Key Allocation Page Changeover (Prev. page) LEFT Page Changeover (Next page) RIGHT Cancel / Return to prev. page. HOME Item Item Contents Information Display Bluetooth Firmware Bluetooth Firmware Version [ ****** ]: Value of Version [ NO_SET ]: No information AVIC-Z110BT/XN/UC...
Page 92
Error Info 1, 2 : Additional Information Version Info : Program version Versions for boot loader, platform and application are displayed. File : Display file name where error happened. : Log information (The content is displayed only when saved) AVIC-Z110BT/XN/UC...
Page 93
HOME : Return to main menu The history is saved in the following folder configuration; SD or USB Memory error.txt <- Error History log.txt <- Log History AstLog <- Exception History Folder DBMSG000.log SYSER000.log EMERG000.log EMERG001.log (Histories may be saved up to EMERG511.log) AVIC-Z110BT/XN/UC...
Page 94
If "Complete" is not displayed in 1 minute after the percentage reaches 100%, turn OFF and ON ACC, and then implement the writing of Bluetooth firmware again. 6. Opening Data Write . . . Startup screen data is written. AVIC-Z110BT/XN/UC...
Page 95
4 GPS RF Unit Confirm connection status Less than 1 second Connected !!ERROR!! 5 iPod Authentication Chip Confirm connection status Less than 1 second Connected !!ERROR!! 6 Bluetooth Unit Confirm communication Approx. 60 seconds, Connected !!ERROR!! setup status max. AVIC-Z110BT/XN/UC...
Page 96
At the calibration test, calibration adjustment is performed to compensate the misalignment of the touch panel. User touches displayed 17 points in order and correction is automatically performed after touching. At the User Calibration Confirmation, it is displayed that whether the user has executed calibration adjustment or not. AVIC-Z110BT/XN/UC...
Page 97
[FINISHED] is displayed and if the calibration is unsuccessful, [NG] is displayed. Return to main menu with [HOME] key. 3. User Calibration Confirmation The following is displayed when User already performed calibration Executed User not performed yet calibration Not executed AVIC-Z110BT/XN/UC...
Page 98
CheckSum Display the checksum of adjustment item group displayed on screen in hexadecimal. In the case of group which does not have checksum, the value is indicated as ------. Source Display the source name of image indicated as background. AVIC-Z110BT/XN/UC...
Page 99
COM_DC value in hexadecimal. This is just the item for indication and not adjustable. 3. Backlight Test <<Items>> Contents Item Name Backlight Brightness Data Current backlight brightness (microcomputer saved value). Backlight Brightness Chg Backlight brightness is adjustable by the set value. AVIC-Z110BT/XN/UC...
Page 100
E2PROM Write ON/OFF setting of writing to E2PROM 5. E2PROM Initialize [Range Selection Screen] <<Items>> Item Contents Item All Initialize Perform initialization of E2PROM entire region. Part Initialize Perform initialization of E2PROM specified region (Region assigned by the Design Division). AVIC-Z110BT/XN/UC...
Page 101
0x00000001 DISC EJECT MODE 0x20000013 NAVI/AV VOL UP 0x20000008 VOL UP VOL DOWN 0x20000009 VOL DOWN LEFT 0x20000006 LEFT RIGHT 0x20000007 RIGHT VOICE UI 0x2000001a VOICE RECOGNITION HOME+LEFT 0x0002001b MENU+LEFT HOME+RIGHT 0x0002001c MENU+RIGHT LEFT+MODE 0x0002001d LEFT+NAVI/AV EJECT+MODE 0x0002001e EJECT+NAVI/AV AVIC-Z110BT/XN/UC...
Page 102
Hi: K-mode signal is detected at the UI of this application. Low: Not detected. 5. High side SW Overcurrent Detection Signal Input for USB Overcurrent Protection: At this port, status is displayed as the detection of short-circuit of power supply for iPod (USB). Hi: Normal operation Low: Short-circuit detected AVIC-Z110BT/XN/UC...
Page 103
Boot sector incorrect 2000570d Not supported drive 2000570e Drive information failed to be obtained 2000570f No consecutive vacant region exists 20005710 Device connection failed to be released 20005711 Device connection start failed 20005712 Synchronous object generation failed 20005713 Incorrect parameters AVIC-Z110BT/XN/UC...
Page 104
Screen for Starting Scan Disc Screen for Scan Disc under Executing Screen for Executed Result of Scan Disc In the case of total error number being zero after the execution of scan disc, “There isn’t error on the volume” is displayed. AVIC-Z110BT/XN/UC...
Page 105
Time of Update (Only at the time of file) At the time of File: Extension Indication Displaying File Attribute (Only at the time of file) W: Writing Approval Attribute R: Writing Prohibition Attribute H: Hidden Attribute A: Archive Attribute S: System Attribute AVIC-Z110BT/XN/UC...
Page 106
Altitude Accuracy for VDOP GPS Time Latitude Velocity in Horizontal Direction Longitude Azimuth of Velocity in Horizontal Direction Altitude Velocity in Vertical Direction Long Axis of Error Ellipsoid Short Axis of Error Ellipsoid Long Axis Inclination of Error Ellipsoid AVIC-Z110BT/XN/UC...
Page 107
Received Signal Level Positioning Status Accuracy * The Third Page [Diag] Channel : GPS Diagnostic Result Antenna Shot : Detection of Antenna Short Circuit Antenna Open : Detection of Antenna Open Circuit Backup Error : Detection of Backup Error AVIC-Z110BT/XN/UC...
Page 108
* The Fourth Page [Err Info] Count Error Number Week of Error Time of Error Happened Day of the Week Happened 13. GPS Assessmentt Version information for GPS driver and sensor module are displayed on the screen. AVIC-Z110BT/XN/UC...
Page 109
14. Clear GPS Backup Data Perform the resetting of GPS driver, clearing backup data and display the result on the screen. [At the time when the clearing of GPS backup is successful] [At the time when the clearing of GPS backup is unsuccessful] AVIC-Z110BT/XN/UC...
Page 110
At the same time, clear the learning data saved in FLASH and SRAM. [At the time when the clearing of learning degree in Gyro Sensor is successful] [At the time when the clearing of learning degree in Gyro Sensor is unsuccessful] AVIC-Z110BT/XN/UC...
Page 111
Vehicle speed pulse distance Display Content of LOW SPEED DISTANCE Status of SPEED PULSE Display SPEED PULSE Low speed vehicle speed pulse under learning CHECK Low speed vehicle speed pulse, OK Low speed vehicle speed pulse, NG Others ----- AVIC-Z110BT/XN/UC...
Page 112
This screen is also displayed when Bluetooth is internally used in other test. Please execute Bluetooth Unit test again after depressing [HOME] key or resetting. 0. Sub Menu Screen Select item with [ ], [ ] keys and determine with [MODE] key. Return to the main menu with [HOME] key. AVIC-Z110BT/XN/UC...
Page 113
* Items 10, 11 and 12 on page 1 are not usable. [MODE SET ERROR!!!] is displayed. Please execute the test of items on page 4, 5 and 6, respectively. (The test content becomes in the form of 10, 11 and 12 of items 36 ~ 44.) AVIC-Z110BT/XN/UC...
Page 114
40_10 41_10 42_10 43_10 44_10 Page 5 36_11. Using Only 20 Mid Channel (31-50) 37_11 38_11 39_11 40_11 41_11 42_11 43_11 44_11 Page 6 36_12. Using Only 20 High Channel (60-79) 37_12 38_12 39_12 40_12 41_12 42_12 43_12 44_12 AVIC-Z110BT/XN/UC...
Page 115
Select item with [ ], [ ] keys and determine with [MODE] key. Return to the sub menu with [HOME] key. Flow of Process After the detailed setting which was performed on [1. Parameter Setting], select [2. Execute] and emit the radio wave which was set by depressing [HOME] key. AVIC-Z110BT/XN/UC...
Page 116
Move the digit of numerical value desired to be set (cursor indicated with blue color) with [ ], [ ] keys. Change the numerical value with [ ], [ ] keys. Value is set with [MODE] key and return to Output Frequency Channel Extended Test menu. Return to Output Frequency Channel Extended Test menu with [HOME] key. AVIC-Z110BT/XN/UC...
Page 117
Test menu, then the set radio wave is emitted by depressing [MODE] key. *The set content is able to be confirmed on the screen by depressing [HOME] key after selecting [1. Parameter Setting]. Please start the measurement. Return to Output Frequency Channel Extended Test menu with [HOME] key. AVIC-Z110BT/XN/UC...
Page 118
(002-254) Value in parenthesis is able to be set arbitrarily 6. Scrambler Mode 0. OFF 1. ON 7. Power Level 0. Power Level 0 1. Power Level 1 2. Power Level 2 3. Power Level 3 4. Power Level 4 AVIC-Z110BT/XN/UC...
Page 119
• In the Case of Internal Buffer Generation not Successful Fail to create internal buffer. • In the Case of Writing a File not Successful File write error. • In the Case of Verify not Successful Fail to verify data. AVIC-Z110BT/XN/UC...
Page 120
NAND-FLASH anymore. CRC Error, This is displayed when data writing/reading is failed. Uncorrectable Error Device under This is displayed when NAND-FLASH is under preparation Preparation (such as under mounting) and unusable. Other Errors Displayed when errors are other than above. AVIC-Z110BT/XN/UC...
Page 121
This happens when play targeted file is not found. Device open failed. This happens when software setting for play is unsuccessful. Fail to create internal buffer. Securing memory required for play is unsuccessful. Device Error. Problem happens in software processing during audio playing. AVIC-Z110BT/XN/UC...
Page 122
This is the 32-gradation image from 0% white to 100% white. 7. NATURAL PICTURE The figure image is displayed. An arbitrary image file can be displayed by placing an arbitrary image file with the file name "Natural.jpg" on the route of SD or USB. AVIC-Z110BT/XN/UC...
Page 123
• CC Part Temperature Sensor 2B0 [- 30°C] ~ 10C [85°C]: Normal Operation Range (determination is not displayed) Other than above: NG • LCD Temperature Sensor 3F6 [- 25°C] ~ 015B [85°C]: Normal Operation Range (determination is not displayed) Other than above: NG AVIC-Z110BT/XN/UC...
Page 124
: Switchover of GMUTE port HOME : Return to Main Menu Error message • When the setting of AC97 Codec is failed Failed to CODEC through setting. • When the setting of MUTE port is failed Failed to port control. AVIC-Z110BT/XN/UC...
Page 125
Possible hardware failure exists. Failed to mute off. Mute releasing of AV source is unsuccessful. Possible hardware failure exists. Device Open Error. Software setting for playing sinusoidal wave is unsuccessful. Device Error. Problem happens in software processing during audio playing. AVIC-Z110BT/XN/UC...
Page 126
Possible hardware failure exists. Failed to mute off. Mute releasing of AV source is unsuccessful. Possible hardware failure exists. Device Open Error. Software setting for playing sinusoidal wave is unsuccessful. Device Error. Problem happens in software processing during audio playing. AVIC-Z110BT/XN/UC...
Page 127
POWER CONTROL NG This is displayed when fan power source control is unsuccessful. STOP<=>FAST POWER CONTROL NG This is displayed when fan power source control is unsuccessful. SLOW<=>FAST SPEED CONTROL NG This is displayed when fan speed control is unsuccessful. AVIC-Z110BT/XN/UC...
Page 128
Manufacturer code of connected wired remote control is displayed on the screen. 0. Wired Remote Control Test Menu This is the menu screen for selecting items which configure this test. 1.1. Remote Control Key Code Obtainment (Key Code not obtained) This is the case of key code not obtained. AVIC-Z110BT/XN/UC...
Page 129
VOL UP 0x00010008 VOL DOWN 0x00010009 BAND 0x0001000A PHONE 0x0001000B ON HOOK 0x0001000C OFF HOOK 0x0001000D SAT TEXT 0x0001000E Audio Recognition 0x0001001A 2.1. Manufacturer Code Input Information (Under Obtainment) Obtain the manufacturer code for the connected wired remote control. AVIC-Z110BT/XN/UC...
Page 130
* Manufacturer Code is obtainable only for Japanese Domestic model. Value of [FF] is displayed this model. 2.3. Manufacturer Code Input Information (Obtainment Failed) If the obtained code is abnormal value, this becomes NG and the screen below is displayed. AVIC-Z110BT/XN/UC...
Page 131
It takes approximately 6 seconds for the setting. 2. Time Display Screen When the setting of simulation time is successful, the screen becomes as follows. In addition, current time is set under the condition of the GPS antenna connected. AVIC-Z110BT/XN/UC...
Page 132
Securing the memory for data comparison was unsuccessful. Data write error Data writing was unsuccessful. Data seek error File pointer operation was unsuccessful. Data read error Reading out of data was unsuccessful. Data verify error Data comparison was unsuccessful. AVIC-Z110BT/XN/UC...
Page 133
Securing the memory for data comparison was unsuccessful. Data write error Data writing was unsuccessful. Data seek error File pointer operation was unsuccessful. Data read error Reading out of data was unsuccessful. Data verify error Data comparison was unsuccessful. AVIC-Z110BT/XN/UC...
Page 134
Case 2. Failed to Change Source of iIPod/AUX. Source switchover for microcomputer was unsuccessful. Case 3. Failed to Setup iPod/AUX-OFF. Input OFF setting for microcomputer was unsuccessful. Case 4. Failed to Attest iPod. iPod authentication was unsuccessful at the start of test. AVIC-Z110BT/XN/UC...
Page 135
Case 1. Failed to Setup VTR-ON. Input ON setting for microcomputer was unsuccessful. Case 2. Failed to Change Source of VTR. Source switchover for microcomputer was unsuccessful. Case 3. Failed to Setup VTR-OFF. Input OFF setting for microcomputer was unsuccessful. AVIC-Z110BT/XN/UC...
Page 136
In the case microcomputer communication was unsuccessful. 2. Display Directly This is the screen when back camera image is under display. The following error message is displayed when error happens; Case. Failed to Setup BackCamera. In the case microcomputer communication was unsuccessful. AVIC-Z110BT/XN/UC...
Page 137
It is OK when a white light is ON. This is the screen for RGB Key Illumination Test. RGB illumination for hard key glows white. The following error message is displayed when error happens; Case: Microcomputer Communication Error Microcomputer communication was unsuccessful. AVIC-Z110BT/XN/UC...
Page 138
This is the test item to confirm whether the closing of drive mechanism is performed correctly or not. If the RPS value obtained at close status corresponds to 0x06h - 0x36h Then the test is OK. In other cases, the test is NG. Test Screen When Test is OK When Test is NG AVIC-Z110BT/XN/UC...
35. Product Information The product information allocated to the product is displayed on the screen. 16 digit values sectioned into four (4) separated by a dot are displayed on the screen. Example: 0000.1111.2222.3333 AVIC-Z110BT/XN/UC...
If you select the DVD source, the test mode screen shown in the left figure is displayed. Press "List" to display the list on the screen. Operate the flow chart of the mechanism test mode with buttons shown in the left screen. Up to lists 01 to 08 AVIC-Z110BT/XN/UC...
Page 141
In order to F close after focus search (S character measurement mode), set to Power_OFF first then power on again FEMIN level before F close. ASMAX level ENVMAX level FE normalization coefficient Spindle gain coefficient TEMAX level indication TEMIN level indication AVIC-Z110BT/XN/UC...
Page 142
Designation of digit by command (1) and (2). UP/DOWN of numbers by command (3) and (4). Fix by command (5). Error occurrence at Power_OFF [Note] If an error occurs at Power_OFF, reset cannot be made. In such a case, it is necessary to turn the power off and start the test mode once again. Error display AVIC-Z110BT/XN/UC...
Page 143
[Note] If the power on time is 999999 hours or more, it is always reported as 999999 hours. [Note] If the power on time is “*E** ****”, the value may not be correct due to the life of the flash memory. AVIC-Z110BT/XN/UC...
Page 144
2: DVD Dual Layer Completion 3: CD 5 Return select 4: CD-RW CRG moves 5: Return to the most outer <Error> ERROR 1: Power OFF select Code : 00000000 Please Input Number <Error : Power OFF> ERROR Code : 00000000 Please Reset AVIC-Z110BT/XN/UC...
When Monitor Assy is removed, Fig.2 it is noted that the length of the Flexible PCB is short. (CD cases) Flexible PCB Remove the two screws and then remove Holder. (Fig.3) Disconnect the Flexible PCB Holder from the connector. (Fig.3) Fig.3 AVIC-Z110BT/XN/UC...
Page 146
- How to Attach the Coaxial Jumper For inserting Coaxial Jumper, adjust cord assy with the engagement axis of connector and insert it as vertically as possible. Do not insert the Coaxial Jumper in extreme slant, as the connector might suffer damage. AVIC-Z110BT/XN/UC...
Page 147
• Lighting confirmation of all LED Fig.7 • All switch operation confirmations • Connected confirmation of Bluetooth • Bend the cable of a broken line part. • Don’t bend it while rubbing right and left. AVIC-Z110BT/XN/UC...
Page 148
Panel Unit Remove the six screws.(Fig.10) Remove the two hooks and then remove Panel Unit.(Fig.10) Fig.10 Removing the DVD Mechanism Module (Fig.11) DVD Mechanism Module Remove the four screws. Disconnect the FFC and then remove the DVD Mechanism Module. Fig.11 AVIC-Z110BT/XN/UC...
Page 149
There is not a terminal peeling off. Fig.13 Remove the five screws and then remove the Upper and Lower Chassis.(Fig.14) Upper Chassis Lower Chassis Fig.14 Removing the Audio Unit (Fig.15) Remove the five screws and then remove the Audio Unit. Fig.15 Audio Unit AVIC-Z110BT/XN/UC...
Page 150
Removing the Navi Unit (Fig.18) Remove the six screws and then remove the Navi Unit. Fig.18 Navi Unit Removing the Tuner IF Unit (Fig.19) Disconnect the FFC.(Fig.13) Remove the three screws and then remove the Tuner IF Unit. Fig.19 Tuner IF Unit AVIC-Z110BT/XN/UC...
Page 151
Gear(ENV1630). Confirm method 1. The Test mode is started. 2. "34. Mecha Close Position Confirmation" is selected. 3. It is confirmed that check results are "OK". Please set position of the gear again for "NG". AVIC-Z110BT/XN/UC...
Page 152
FPC is moved to the direction of the arrow like this state, the hole of the monitor case and the hole of FPC are put together, and the cover is fixed. Monitor case Don't catch FPC in the holder. FPC is attached in the direction of figure. AVIC-Z110BT/XN/UC...
Page 153
Attention at assembly of DVD Mechanism Module (LS1) Short FFC is positioned that reinforcement plate is short on the mechanism side. FFC doesn't protrude beyond the main body of mechanism. AVIC-Z110BT/XN/UC...
Page 154
(4), (5), (6) Stick insulator aside to corner ( line). (7)Sets it to the position under the hole ( line=hole of chassis) and stick it. (8), (9), (10), (11), (12) Stick it aligning DVD mech module side ( line) with cover side. (11) (12) (10) AVIC-Z110BT/XN/UC...
Page 155
How to have it 1.Have a specified part. Handling OK Handling NG AVIC-Z110BT/XN/UC...
Page 156
(Precaution) If the PU goes to the outer most periphery, it idles. It is not a problem, but please try not to let it idle as much as possible. GND the brown line 4V to the gray line Fig. 1 Fig. 2 Connector (relay FFC) Relay FFC AVIC-Z110BT/XN/UC...
Page 157
Fig. 1 T-case washer Drive gear Fig. 2 c.Clamp state with no disc loaded a.Ejecting state b.Open-lock state There is a There is space no space AVIC-Z110BT/XN/UC...
Page 158
6.As in the Figures, while supporting the location A with your fingers, screw the relay PCB. (Fig. 7 / Fig. 8) 7.Solder the lead for the CRG motor. 8.Fit the relay FFC to the connector. Fig. 7 Fig. 8 AVIC-Z110BT/XN/UC...
Page 159
(Precaution) The relay FFC must be removed for certainty in order to prevent the IC damage. 2.Apply 1.5V to the CRG motor and then transfer the PU to the outer periphery. (Precaution) Do not forget to reinstall the relay FFC after sending the PU to the outer periphery and take the necessary measures. AVIC-Z110BT/XN/UC...
Laser didoes may be damaged, if the volume switch for the minus side of the probe, the body frame of the the laser power adjustment of the pick up unit, is turned. measurement device should be set to floating ground. AVIC-Z110BT/XN/UC...
Page 161
Oscilloscope Symptom in case the adjustment is not adequate: Worsening of the error rate 10 (Normally 10 or less.) Large RF jitter RF waveform distortion Tracking drawing/Unstable servo * Caution: Do not look into the laser light during adjustment. AVIC-Z110BT/XN/UC...
Page 162
Next, slightly turn the skew adjusting screw B so the level would reach its maximum. Slightly turn the skew adjusting screw A again so the level would reach its maximum. (Make adjustment in the order of A->B->A and in the end complete adjustment by turning each screw in the clockwise direction.) AVIC-Z110BT/XN/UC...
Page 163
5: CRG Move Outer 6: Eject Please Input Number 12. In order to produce the clamping state with no disc loaded, slightly move the disc detection arm in the counterclockwise direction while moving the switch arms outward. Switch arms AVIC-Z110BT/XN/UC...
Page 164
1: Power OFF CRG Move Outer 1: Power OFF Please Input Number 15. TEST MODE Select “6: Eject.” TEST MODE 1: LD ON 2: ASMAX 3: Skew Adjustment 4: Error Rate 5: CRG Move Outer 6: Eject Please Input Number AVIC-Z110BT/XN/UC...
Page 165
Locations to make SKEW adjustment Locations to adhere the SKEW 1,2,3: GEM1033 AVIC-Z110BT/XN/UC...
Page 166
Bond for resonance 4:Three Bond 1530 adhesive Bond for locking the screw 5,6 : Three Bond 1401M Bond for locking the screw AVIC-Z110BT/XN/UC...
Page 167
Precautions on handling the PU *Precaution: Do not touch those shaded areas in the following figures. Hologram (Beware of the static) Do not touch the optical part RF level adjusting part Do not touch the spring AVIC-Z110BT/XN/UC...
Input signal Output signal Masuring Specs Adjusting (Measurement point, instruments point wave pattern) Front monitor GGV1025 TP : FVA Oscilloscope 0.7 V ± 0.007 Vpp VR2731 picture level Title3 chap3 play Refer to following 100 IRE(White 100%) 1.0 Vpp AVIC-Z110BT/XN/UC...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING F10BT/XN/AU F10BT/XN/AU AVIC-Z110BT/XN/UC...
Page 171
Part No. Language * CRB3051 (UC) English * CRB3052 (UC) Russian * CRB3055 (AU) English All operation manuals are supplied in PDF files by the CD-ROM. Regarding the availability of paper manual, contact Pioneer Service representative in your region. AVIC-Z110BT/XN/UC...
Page 173
CNN3148 Sheet CNN3149 Heat Sink CNR1988 Navi Unit CWN3985 Shield CND4932 Holder CND4933 Holder CND4935 Service CC Assy(UC) CXX2608 Service CC Assy(AU) CXX2607 Holder Unit CXE2706 Chassis Unit CXE1612 Shield Unit CXE1620 DVD Mechanism Module(LS1) CXK6801 Fan Motor CXM1394 AVIC-Z110BT/XN/UC...
9.4 EXTERIOR(3) The Plate (No.30) and the right and left Guide (No.28, 29) cannot be removed. In the component replacement, please exchange each Grille Unit (No.26). AVIC-Z110BT/XN/UC...
Page 177
CNN2822 LCD Panel CWX3813 Holder Unit CXE1741 Case Unit CXE2836 Cushion CNN3115 Grille Unit(UC) CXE2206 Grille Unit(AU) CXE1974 Grille CNS9807 Guide CNS9824 Guide CNS9825 Plate(UC) CNS9899 Plate(AU) CNS9949 Button Unit CXE1706 Panel Unit(UC) CXE1991 Panel Unit(AU) CXE1992 Case CNB3574 AVIC-Z110BT/XN/UC...
COIL U CSN1068-A COIL V CN1201 DSCSNS HALL W+ DSCSNS1 DSCSNS1_B DSCSNS0 DSCSNS0_B CSN1068-A HALL W- R103 HALL V+ S102 HALL V- HALL U+ HALL U- HALL BIAS- CRGP CRG+ CRGM LOAD/CRG MOTOR CRG- CXC4026 SPINDLE MOTOR EXM1050 CKS6063 CN101 AVIC-Z110BT/XN/UC...
Page 280
- CC UNIT Each power supply start wave pattern Power supply control line start timing RST cancellation timing AVIC-Z110BT/XN/UC...
Page 281
During Prima and TCON During T-CON and LVDS AVIC-Z110BT/XN/UC...
Page 282
NAVI UNIT MONITOR UNIT LVDS LVDS Tx LVDS Rx 120pin B to B connector Monitor connector and flexible cable LVDS waveforms(Measures it in this side of the RX.) 1.0 ns/div 250 ps VOD = About 450 mV ACQCLK waveforms AVIC-Z110BT/XN/UC...
Page 283
- AUDIO UNIT VTR input and a composite wave pattern after the adjustment VTR2 input VTR2 input 1 Vpp After VR After VR adjustment adjustment 0.7 Vpp VTR2 input(color bar) VTR2 input(white 100%) AVIC-Z110BT/XN/UC...
Unit Number : CWN4335(UC) Q 2071 (A,28,36) Transistor 2SA1577 Unit Number : CWN4336(AU) Q 2072 (A,31,36) Chip Transistor DTC114EUA Unit Name : Audio Unit Q 2101 (B,118,28) Chip Transistor UMF21N Q 2181 (B,90,36) Transistor UMD3N Q 2182 (B,89,29) Transistor 2SD1767 MISCELLANEOUS AVIC-Z110BT/XN/UC...
Page 311
D 2240 (B,111,107) Diode 1SS355 L 2554 (B,112,19) Inductor CTF1410 D 2241 (A,67,98) Diode 1SS352 L 2571 (B,17,35) Inductor CTF1306 D 2296 (B,144,103) Diode 1SR154-400 L 2622 (A,94,63) Inductor CTF1410 D 2297 (B,144,108) Diode 1SR154-400 L 2641 (A,143,98) Inductor CTF1410 AVIC-Z110BT/XN/UC...
Page 312
(B,16,125) 4.7 kohm CCN1180 R 2232 (B,70,34) RS1/16SS153J R 2048 (B,13,127) RS1/10SR103J R 2233 (B,68,34) RS1/16SS103J R 2056 (B,69,81) RS1/16SS472J R 2234 (B,66,34) RS1/16SS102J R 2061 (A,19,41) RS1/16SS472J R 2239 (B,112,107) RS1/8SQ103J R 2062 (A,20,37) RS1/16SS472J R 2241 (A,71,97) RS1/16SS391J AVIC-Z110BT/XN/UC...
Page 313
R 2373 (A,55,40) RS1/10SR0R0J R 2453 (B,52,63) RS1/16SS102J R 2375 (B,51,34) RS1/16SS681J R 2454 (B,53,63) RS1/16SS0R0J R 2376 (A,53,40) RS1/16SS681J R 2458 (A,52,62) RS1/16SS473J R 2377 (A,50,35) RS1/16SS681J R 2460 (B,55,64) RS1/16SS561J R 2378 (A,48,36) RS1/16SS681J R 2461 (B,62,65) RS1/16SS473J AVIC-Z110BT/XN/UC...
Page 314
R 2560 (B,118,19) RS1/16SS102J R 2669 (B,142,58) RS1/10SR0R0J R 2561 (B,120,19) RS1/16SS221J R 2673 (B,142,62) RS1/10SR101J R 2562 (B,121,19) RS1/16SS221J R 2677 (B,145,50) RS1/16SS0R0J R 2569 (A,27,65) RS1/16SS0R0J R 2678 (B,142,50) RS1/16SS0R0J R 2570 (A,28,92) RS1/16SS0R0J R 2681 (B,145,46) RS1/10SR0R0J AVIC-Z110BT/XN/UC...
Page 315
R 2772 (A,90,81) RS1/10SR0R0J R 2993 (A,7,25) (AU) RS1/16SS332J R 2773 (B,111,70) RS1/10SR102J R 2995 (A,7,22) (UC) RS1/16SS333J R 2774 (B,111,90) RS1/10SR102J R 2996 (A,7,19) RS1/16SS0R0J R 2775 (B,104,71) RS1/10SR0R0J CAPACITORS R 2776 (B,104,89) RS1/10SR0R0J R 2777 (A,122,84) RS1/10SR472J AVIC-Z110BT/XN/UC...
Page 316
C 2227 (B,58,140) CKSSYB102K50 C 2491 (A,12,40) CKSRYB104K16 C 2232 (A,60,118) CKSRYB103K50 C 2492 (A,8,47) CKSSYB102K50 C 2238 (B,113,110) CKSRYB103K50 C 2493 (A,13,45) CKSRYB104K16 C 2241 (A,70,89) CEVW470M25 C 2494 (A,15,45) CKSRYB103K50 C 2276 (A,41,76) CEHVW330M16 C 2495 (A,13,43) CKSRYB823K16 AVIC-Z110BT/XN/UC...
Page 317
C 2662 (B,134,42) CKSRYB104K16 C 2787 (B,115,71) CKSQYB475K10 C 2663 (B,132,41) CKSYB226K6R3 C 2788 (B,114,90) CKSQYB475K10 C 2664 (B,131,43) CKSSYB104K16 C 2789 (B,118,72) CKSQYB475K10 C 2665 (B,137,57) CKSSYB104K16 C 2790 (B,116,90) CKSQYB475K10 C 2666 (B,138,57) CKSSYB104K16 C 2791 (B,120,72) CKSQYB475K10 AVIC-Z110BT/XN/UC...
Page 318
JA401 (A,14,118) Antenna Jack CKX1056 C 516 (B,70,75) CKSQYB334K16 C 517 (A,31,18) CKSRYB103K50 FM/AM Tuner Unit(UC) CWE2097 FM/AM Tuner Unit(AU) CWE2128 C 519 (A,38,73) CEVW471M10 C 520 (A,31,32) CEVW101M16 RESISTORS R 401 (A,27,102) RS1/4SA0R0J R 410 (B,32,40) (UC) RS1/16SS681J AVIC-Z110BT/XN/UC...
Page 319
Q 4901 (A,6,62) Transistor 2SC4617 L 4714 (B,53,90) Inductor CTF1736 Q 4902 (A,20,60) Transistor 2SA1774 L 4715 (A,62,83) Inductor CTF1736 Q 4903 (A,19,86) Transistor 2SC4617 L 4716 (A,62,84) Inductor CTF1736 D 4201 (B,39,18) Diode RB521G-30 L 4718 (B,73,91) Inductor LCYC1R0K2125 AVIC-Z110BT/XN/UC...
Page 320
R 4014 (B,46,72) RS1/16SS0R0J R 4114 (B,41,73) RS1/16SS0R0J R 4016 (B,47,75) RS1/16SS6041F R 4115 (A,42,75) RS1/16SS470J R 4017 (A,36,64) RS1/16SS105J R 4116 (A,44,77) RS1/16SS220J R 4018 (B,47,73) RS1/16SS0R0J R 4117 (A,44,75) RS1/16SS220J R 4020 (A,36,69) RS1/16SS106J R 4118 (A,43,75) RS1/16SS220J AVIC-Z110BT/XN/UC...
Page 321
R 4412 (B,78,43) RS1/16SS220J R 4229 (B,59,45) RS1/10SR103J R 4230 (B,57,44) RS1/10SR102J R 4413 (B,78,42) RS1/16SS220J R 4231 (A,53,49) RS1/16SS220J R 4414 (A,51,48) RS1/16SS103J R 4233 (A,29,86) RS1/10SR0R0J R 4415 (A,63,41) RS1/16SS471J R 4234 (B,24,65) RS1/10SR0R0J R 4419 (A,51,49) RS1/16SS473J AVIC-Z110BT/XN/UC...
Page 322
R 4634 (B,55,22) RS1/16SS0R0J R 4736 (B,63,86) RS1/16SS102J R 4635 (B,59,25) RS1/16SS0R0J R 4739 (A,52,83) RS1/16SS151J R 4636 (B,45,22) RS1/16SS0R0J R 4740 (A,55,89) RS1/16SS0R0J R 4637 (B,47,41) RS1/16SS0R0J R 4742 (A,61,91) RS1/16SS0R0J R 4638 (B,45,22) RS1/16SS0R0J R 4771 (A,55,35) RS1/16SS103J AVIC-Z110BT/XN/UC...
Page 323
R 4926 (A,23,84) RS1/16SS274J R 4993 (B,30,26) RS1/16SS562J R 4928 (A,25,89) RS1/16SS0R0J R 4994 (A,6,56) RS1/16SS104J R 4929 (A,25,88) RS1/16SS0R0J R 4995 (A,29,67) RS1/16SS151J R 4930 (A,28,85) RS1/16SS0R0J R 4996 (A,30,65) RS1/16SS151J R 4932 (A,27,86) RS1/16SS223J R 4997 (A,30,67) RS1/16SS151J AVIC-Z110BT/XN/UC...
Page 324
C 4056 (B,44,63) CKSSYB104K10 C 4221 (A,24,42) CKSRYB105K10 C 4057 (B,42,65) CKSSYB104K10 C 4222 (B,69,13) CCSSCH100D50 C 4059 (B,42,66) CKSSYB104K10 C 4223 (B,34,12) CCSSCH220J50 C 4060 (B,44,66) CKSSYB104K10 C 4224 (A,19,29) CKSSYB392K50 C 4061 (B,43,68) CKSSYB104K10 C 4226 (A,26,44) CKSRYB105K10 AVIC-Z110BT/XN/UC...
Page 325
C 4410 (A,77,68) CKSSYB103K16 C 4609 (A,44,35) CKSRYB104K50 C 4411 (A,73,52) CKSSYB104K10 C 4613 (B,40,30) CKSSYB473K10 C 4412 (A,77,64) CKSSYB103K16 C 4614 (B,23,45) CKSSYB104K10 C 4413 (B,63,77) CKSRYB105K10 C 4621 (B,59,28) CKSSYB473K10 C 4414 (A,78,27) CKSSYB103K16 C 4622 (B,57,24) CKSSYB473K10 AVIC-Z110BT/XN/UC...
Page 326
C 4809 (B,21,72) CKSSYB103K16 C 4869 (B,25,79) CKSSYB103K16 C 4810 (B,24,74) CKSSYB103K16 C 4870 (B,27,81) CKSSYB103K16 C 4811 (B,21,73) CKSSYB103K16 C 4871 (B,26,81) CKSSYB103K16 C 4812 (B,23,72) CKSSYB103K16 C 4872 (B,25,81) CKSSYB103K16 C 4813 (B,22,74) CKSSYB103K16 C 4901 (B,21,70) CKSSYB103K16 AVIC-Z110BT/XN/UC...
Page 327
(B,114,103) Diode RB551V-30 C 4985 (B,23,83) CKSSYB103K16 D 5005 (B,116,105) Diode HZU6R8(B1) C 4986 (B,25,83) CKSQYB106K6R3 D 5006 (B,112,104) Diode HZU11(B2) C 4987 (B,31,75) CKSQYB106K6R3 D 5007 (A,129,85) Diode RB551V-30 D 5008 (B,125,85) Diode RB551V-30 C 4988 (A,20,84) CKSSYB103K16 AVIC-Z110BT/XN/UC...
Page 328
R 5132 (B,118,86) RS1/10SR153J CN5602 (A,100,50) Connector CKS6116 R 5136 (A,128,32) RS1/10SR102J CN5603 (B,151,51) Connector CKS6123 R 5140 (B,119,81) RS1/10SR153J JA5201 (A,166,113) Connector CKS5749 R 5141 (B,122,82) RS1/10SR681J JA5202 (A,162,126) Connector CKS5702 R 5144 (A,70,24) RS1/16SS0R0J JA5251 (A,90,128) Connector CKS5589 AVIC-Z110BT/XN/UC...
Page 329
R 5476 (B,132,69) RS1/10SR0R0J R 5647 (A,108,61) RS1/16SS0R0J R 5481 (B,132,65) RS1/10SR0R0J R 5648 (A,110,61) RS1/16SS0R0J R 5501 (B,160,88) RS1/16SS0R0J R 5650 (A,111,50) RS1/16SS0R0J R 5502 (B,161,89) RS1/16SS0R0J R 5651 (A,109,57) RS1/16SS0R0J R 5503 (B,160,92) RS1/16SS202J R 5653 (A,114,57) RS1/16SS0R0J AVIC-Z110BT/XN/UC...
Page 330
C 5106 (A,121,90) CKSQYB103K50 C 5452 (B,67,19) CKSQYB475K10 C 5107 (A,56,73) CKSQYB104K50 C 5453 (B,57,16) CCSRCH391J50 C 5108 (A,51,75) CEVW101M16 C 5454 (B,64,21) CCSRCH391J50 C 5110 (A,41,74) CEVW101M16 C 5455 (B,52,16) CCSRCH221J50 C 5111 (A,74,20) CEVW101M16 C 5456 (B,63,18) CCSRCH221J50 AVIC-Z110BT/XN/UC...
Page 331
Q 3002 (B,104,42) FET RSQ035P03 L 3164 (A,37,38) Inductor CTF1748 Q 3003 (B,95,22) Transistor 2SA1577 L 3165 (A,36,58) Inductor CTF1748 Q 3004 (B,97,19) Transistor 2SC4097 L 3166 (A,36,37) Inductor CTF1748 Q 3005 (B,95,32) Transistor DTC114EE L 3167 (A,31,55) Inductor CTF1748 AVIC-Z110BT/XN/UC...
Page 332
R 3002 (B,129,28) RS1/10SR6801D R 3134 (B,123,58) RS1/10SR3602D R 3003 (B,125,29) RS1/10SR2000D R 3135 (B,122,59) RS1/10SR1801D R 3004 (B,125,28) RS1/10SR1001D R 3136 (A,126,72) RS1/8SQ0R0J R 3005 (B,130,36) RS1/10SR0R0J R 3137 (B,124,66) RS1/10SR0R0J R 3006 (B,129,32) RS1/10SR1001D R 3150 (A,47,48) RS1/16SS1000D AVIC-Z110BT/XN/UC...
Page 333
R 3321 (A,78,17) RS1/10SR2000D R 3424 (B,106,13) RS1/16SS104J R 3322 (A,80,17) RS1/10SR2400D R 3432 (A,139,27) RS1/16SS0R0J R 3323 (A,78,20) RS1/10SR2000D R 3324 (A,79,22) RS1/10SR2400D CAPACITORS R 3325 (A,75,23) RS1/10SR333J C 3001 (B,124,54) 100 uF CCG1232 R 3326 (A,69,16) RS1/10SR2000D AVIC-Z110BT/XN/UC...
Page 334
CCSSCH470J50 C 3369 (A,82,35) CKSQYB106K6R3 C 3106 (B,113,67) CKSSYB473K16 C 3370 (B,91,34) CKSSYB104K10 C 3107 (B,115,65) CKSRYB104K50 C 3371 (B,92,34) CKSSYB104K10 C 3108 (A,123,70) CKSQYB225K10 C 3372 (B,94,34) CKSSYB104K10 C 3111 (A,138,44) 10 uF CCG1223 C 3373 (A,84,29) CKSSYB104K10 AVIC-Z110BT/XN/UC...
Page 335
(A,124,33) CKSRYB104K50 R 1007 (A,29,26) RS1/16SS6801D C 2904 (A,128,33) CKSRYB104K50 R 1019 (B,15,9) RS1/16SS101J R 1021 (A,27,15) RS1/16SS0R0J R 1025 (B,19,11) RS1/16SS101J Unit Number : EXX1060 R 1027 (A,27,19) RS1/16SS101J Unit Name : PCB Unit(Service) R 1101 (A,35,36) RS1/16SS104J AVIC-Z110BT/XN/UC...
Page 336
C 1105 (A,42,45) CKSSYB104K10 R 1514 (A,68,35) RS1/16SS183J C 1106 (A,37,48) CKSSYB103K16 R 1516 (A,65,36) RS1/16SS103J C 1107 (A,41,49) CKSSYB103K16 R 1517 (A,76,16) RS1/16SS103J C 1108 (A,74,42) CKSSYB103K16 R 1518 (A,74,24) RS1/16SS103J C 1109 (A,56,41) CKSRYB224K10 R 1519 (A,70,34) RS1/16SS102J AVIC-Z110BT/XN/UC...
Page 337
C 1526 (A,68,37) CKSSYB103K16 C 1528 (A,78,29) CCSSCH471J16 C 1601 (A,44,29) CKSSYB103K16 C 1602 (A,42,24) CCSSCH101J50 C 1603 (A,44,27) CCSSCH101J50 C 1604 (A,41,27) CCSSCH680J50 C 1605 (A,43,27) CCSSCH680J50 C 1606 (A,41,23) CKSSYB104K10 C 1607 (A,41,35) CKSQYB106K6R3 C 1608 (A,43,36) CKSRYB105K10 AVIC-Z110BT/XN/UC...