Bosch Intuvia PowerPack 400 Original Instructions Manual page 12

OBJ_BUCH-2087-002.book Page 4 Wednesday, July 16, 2014 5:12 PM
Setting the Assistance Level
On the operating unit 10 you can set how much the eBike
drive assists you while pedalling. The assistance level can be
changed at any time, even while cycling.
Note: For individual versions, it is possible that the assistance
level is pre-set and cannot be changed. It is also possible that
less assistance levels are available for selection than listed
here.
The following assistance levels (max.) are available:
– "OFF": The motor assistance is switched off, the eBike can
be operated as a normal bicycle through pedaling.
– "ECO": Effective assistance at maximum efficiency for
maximum cruising range
– "TOUR": Uniform assistance, for touring with long cruising
range
– "SPORT": Powerful assistance for sportive riding off road
as well as for urban traffic
– "TURBO": Maximum assistance, supporting highest ca-
dence for sportive riding
To increase the assistance level, press the "+" 13 button on
the operating unit until the desired assistance level appears in
the display b. To decrease the assistance level, press the
button"–" 12.
The requested motor output is displayed in indicator a. The
maximum motor output depends on the selected assistance
level.
Assistance Level Assistance Factor*
(Derailleur)
50 %
"ECO"
120 %
"TOUR"
190 %
"SPORT"
275 %
"TURBO"
* The motor output can vary for individual versions.
When the on-board computer is removed from the holder 4,
the last indicated assistance level is stored; the motor-output
indicator a remains empty.
Switching the Push/Start Aid On/Off
With the speed version, the push aid can also be used as a
start aid. The start aid is switched off at 18 km/h.
The push/start aid can make it easier for you to push or start
the eBike. The speed of this feature depends on the selected
gear and depending on the model, can reach a maximum of
6 km/h or 18 km/h. The lower the selected gear, the lower the
speed of this function (at full capacity).
 The push/start aid function may only be used when
pushing or starting the eBike. If the wheels of the eBike
have no contact with the ground when using the push aid,
then there is risk of injury.
To switch on the push/start aid, press and hold the "WALK"
14 button on the operating unit. The eBike drive is switched on.
Bosch eBike Systems
The push/start aid is switched off if one of the following
occurs:
– you release the "WALK" 14 button,
– the wheels of the eBike are blocked (e.g. by actuating the
brakes or impacting against an obstacle),
– the speed exceeds 6/18 km/h.
Switching bike lights on/off
In the model in which the lighting is powered by the eBike sys-
tem, the front and rear lights can be switched on and off at the
same time via the on-board computer with button 2.
When the lighting is switched on "Light on" appears and
when the lighting is switched off "Light off" appears for ap-
prox. 1 s in text indication d. The lighting symbol c is dis-
played when the light is on.
Switching the bike light on and off has no effect on the back
lighting of the display.
Version Speed: Daytime running lights are always provided
in this option. When you switch on the eBike system (see
"Switching the eBike System On/Off", page English–3), the
lights will also be switched on. The bike lights cannot be
switched off with button 2.
Speed and Distance Indication
The speed indication f always displays the current speed.
The following functions are available in the function indica-
tion (combination of text indication d and value indication e):
– "Clock": Current time
– "Max. Speed": Maximum speed achieved since the last
reset
– "Avg. Speed": Average speed achieved since the last
reset
– "Trip time": Trip time since the last reset
– "Range": Estimated range of the available battery-pack
charge (for constant conditions such as assistance level,
route profile, etc.)
– "odometer": Display of the total distance travelled with
the eBike (cannot be reset)
– "Distance": Distance covered since the last reset
To switch between display functions, press button "i" 1 on
the on-board computer or button "i" 11 on the operating unit
repeatedly until the required function is displayed.
To reset "Distance", "Trip time" and "Avg. Speed", switch
to any of the three functions and then press and hold the
"RESET" button 6 until the indication is set to zero. This also
resets the values of the other two functions.
To reset the "Max. Speed", switch to this function and then
press and hold the "RESET" button 6 until the indication is set
to zero.
To reset "Range", switch to this function and then press the
"RESET" 6 button until the display is reset to the value of the
factory setting.
If the on-board computer is removed from the holder 4, all val-
ues of the features are saved and can still be displayed.
English–4
0 276 001 SPI | (16.7.14)