Commando -COMBO Installation Manual page 6

Blue - Unlock Green/Black -Trunk
Red -12V+ Out
Red - Factory Disarm
Green - Lock Yellow - Vacuum Sys. (FIG.2)
Switch
White/Yellow -Horn Out (-)
Shock
Red/Black -Dome Light (-)
Sensor Plug
LED
FM
COMBO
ALARM & START
Dip Switches
FIG. 1
MADE IN USA
DIP SWITCH SETTINGS
1-ON= GASOLINE ENGINES
2-ON= NON VACUUM SENSE
3-ON= CRANK TIME NORMAL
4-ON= SMART SENSE
Ground
YELLOW
Vacuum
Switch
VACUUM TEE
5
REMOTE ALARM & STARTER WIRING
RF
Receiver
Parking Lights
White-----
12V + Battery Power
Red--------
Alarm Siren Wire
Brown----
Ground
Black-----
(-) Armed & Start Output
Orange---
Spark Plug Sense
Gray-------
(-) Door Trigger
Green----
(-) Trigger
Blue-------
Violet----- (+) Door Trigger
Yellow---- Brake Light Switch
Violet - Starter
Orange - Accessory
Yellow - Ignition 1
Ignition 2
Brown -
12V + BATTERY
Red -
12V + BATTERY
Red -
FIG. 1
OFF= DIESEL ENGINES
OFF= VACUUM SWITCH SENSE
OFF= CRANK TIME LONGER
OFF= SPARK PLUG OR TACH
Optional
FIG. 2
"YELLOW WIRE"
VACUUM SYSTEM HOOKUP
If Vacuum Hook-Up is required
An additional Vacuum Kit can be added
That includes: Vacuum Switch, Hose,
Vacuum "T", Connectors.
WHITE:-----------
Connect to the (+) side of parking lights.
RED:--------------
Connect to Battery constant 12V.+ power.
BROWN:---------
Connect to the red wire of Siren (+) Output.
BLACK:----------
Connect to a Good Ground.
ORANGE:--------
Connect to a 30 Amp. Relay for Starter Kill (-) Output (PASS LOCK)
GRAY: ------------
Wrap around Any Spark Plug cable or Tachometer.
GREEN:----------- Door pin (-) Trigger.
BLUE:-------------
Hood pin or extra Sensors (-) Trigger.
VIOLET:----------
Door pin (+) Trigger.
YELLOW:--------
Connect to the Brake light switch (+) when Brake is pressed.
RED: ---------
Connect to Battery constant 12V. (+) POWER.
RED: ---------
Connect to Battery constant 12V. (+) POWER.
BROWN:---- Connect to Ignition switch #2 if needed.
Connect to Ignition switch wire which is powered 12V.+ even on cranking.
YELLOW:---
ORANGE:--- Connect to Ignition switch ACC circuit (Air Cond./Heater).
Connect to Starter wire witch is powered ONLY on cranking position.
VIOLET: ----
4- PIN WHITE CONNECTOR:--------- Plug in Shock Sensor.
Plug in Door Lock Unlock Wire.
3- PIN WHITE CONNECTOR:---------
Plug in LED and mount in a desirable location.
2- PIN RED CONNECTOR:------------
2- PIN BLUE CONNECTOR:---------- Plug in PROGRAM/VALET Switch.
2- PIN WHITE CONNECTOR:---------
Plug in Horn / Dome Light Wire.
4- PIN WHITE CONNECTOR:--------
Plug in R/F RECEIVER.
YELLOW: VACUUM (optional)
A. Find the existing Vacuum Hose at the intake manifold. Cut hose and install the
Vacuum Tee included in the optional kit. (See FIG. 2).
B. Connect to one of the pin on the Vacuum switch , and Ground the other Pin.
Please note that Vacuum Hose other than the manifold and less than 10"
vacuum may cause starter damage.
NOTE
1- Factory ALARM disarm pulse will be activated any time alarm disarms
2- The horn output will trigger with all triggers
3- this output is also used to bypass (GM pass-lock. Transponders type immobilizers).
Ground output wire will supply ground when alarm armed, and remote starter is engaged no
matter if ignition is turned on position with the key. Then brake is preset, the output will be
active until user turns off the ignition to off position.
6