Subscribe to Our Youtube Channel
Related Manuals for Commando ALA550
Summary of Contents for Commando ALA550
- Page 1 7/23/02 COMMANDO MODEL ALA550 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS ALA550...
-
Page 2: Wiring Diagram
Brown Wire: (-) 200mA of 2 steps door unlock Output. Pink Wire: (-)200mA Programming Output { Channel 3 (Factory default Setting) / Horn output.} Gray Wire: (-) 200mA Programming Output {Channel 2 (Factory default Setting) / Pager output.} White Wire: (-) 200mA of dome light Output ALA550... - Page 3 Programming) then you must connect the violet wire to the handbrake switch for this application. H7/2. BLUE WIRE -- GROUND INSTANT TRIGGER INPUT -- This wire is the ground trigger input wire for hood/trunk pin switches. H7/3. VIOLET WIRE -- POSITIVE DOOR SWITCH SENSING INPUT-- ALA550...
- Page 4 This wire is provided to use the existing vehicle's horn as the alarm system optional warning audible device. It's a transistorized low current output, and should only be connected to the low current ground output from the vehicle's horn switch. When the system is triggered, the horn will sound. ALA550...
- Page 5 H4. 3 PIN DOOR LOCK HARNESS: INSTALL NEW DOOR LOCK MOTOR ( - ) Unlock Pulse Blue Wire Blue Wire (+) Lock Pulse ( - ) Lock Pulse +12V Green Wire ( + ) Unlock Pulse 3 Pin Plug To Alarm Green ALA550...
- Page 6 3.5 seconds.(See Feuture II – 1 Programming.) Plug Cut the Existing Lock Wire Alarm + 12V OEM Slave Door Lock Switch Unlock Lock H4/1 +12V Blue Wire OEM Driver’s Door Lock Motor To All Other Cut Existing Unlock Wire Door Lock Motors ALA550...
- Page 7 Two Chirps / Three Chirps / Four Chirps / Transmitter LED one pulse LED two pulse LED three pulse LED four pulse Button Factory Default Setting All Chirp on Siren Chirp on only Horn Chirp on only All Chirp off ALA550...
-
Page 8: Alarm Feature
H7/9 Gray Wire H7/9 Gray Wire H7/9 Gray Wire H7/9 Gray Wire = Channel 2 Output = Channel 2 Output = Channel 2 Output = Pager output 1 second pulse Latch output Timer controlled output for trunk output release. ALA550... - Page 9 For example, in your garage you can put a PIR for protection. (A device to detect person's movement in a protected area.) If system armed, a person walk through the detect area, the siren inside the car will alarming to raise the attention to the owner. ALA550...
- Page 10 5. Turn the Ignition Switch to “OFF’ position. You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be repeated three times indicating the new code (92) has been accepted and stored in memory. Test Mode ALA550...
-
Page 11: Return To Factory Default Setting
Activate Anti Car-Jacking Ignition in 'on' position and (2-second) Press and Hold for two seconds Channel 2 (Trunk) Timer Control Press and Hold for 2 seconds (2-second) Passive Arming By-pass While the system disarmed. Button = Panic Function. (Factory Default Setting) ALA550... -
Page 12: Led Indicators
No chirp sound will be heard, arm / disarm confirmation will be through the vehicle’s parking light only. NOISELESS MODE: Press and release the button once: The siren chirps once, The system is armed. ALA550... -
Page 13: Passive Arming
The Override function may be used if the remote transmitter is lost or inoperative. 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2. Within 10 seconds push and release the valet switch ALA550... -
Page 14: Valet Mode
2. During panic mode, the normal function of this transmitter button will be suspended. The buttons can be used to lock and unlock the doors (if the option is installed), however once the button is pressed, the vehicle’s starter disable device, (where installed) will be enable allowing the vehicle to start. ALA550... -
Page 15: Trigger The System
The siren still alarming and the parking light flashing, and b. The starter disable will activate to prevent the vehicle from starting. c. It will remain active until the vehicle's battery power exhausted. OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR JACKING: ALA550... -
Page 16: Dome Light Convenience Delay & Supervision
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. T0723 ALA550...
Need help?
Do you have a question about the ALA550 and is the answer not in the manual?
Questions and answers