Mx-Trx2 - Sharp MX-M283N Installation Manual

J. Function and operation check
Check that the following operations are normal.
Check item list
Key-in (operation panel)
Display (operation panel)
Paper feed Hand feed
operation
Main unit paper
tray
Desk unit paper
feed tray
Paper size detection
Originals size Original table
detection mode
DSPF mode
RSPF mode
DSPF/RSPF S-S mode
operation / two
D-S mode
sided copy
S-D mode
D-D mode
Bookbinding operation
Stapling operation
Grouping operation
Sorting operation
Paper exit operation
K. Setup and adjustment data recording
Print the various setup data and the adjustment data (list) with
SIM22-6 and keep the data.
• In case of a memory trouble, if the data are not kept, all the
adjustments must be made again.
• If the data are kept, the setup values and the adjustment values
can be entered without adjustments, shortening the servicing
time.
L. Necessary works before moving the machine
1) If the following options are installed, remove all of them from
the machine.
• Finisher
• Large capacity tray
2) Remove the following consumable parts from the machine.
• Paper
• Toner cartridges
• Development cartridge
3) Lock the following sections.
• Scanner (Optical section)
• Paper cassette lift plate
NOTE: Since the hard disk drive is built in the machine, use care
not to exert vibrations or shocks to the machine when in
transit.
M. Remote operation panel function Enable
setting
(1) General
To use the remote operation panel function, the password for the
remote operation panel function must be entered on the password
input menu displayed on the VNC boot screen. Note that, therefore,
the password must be set in advance to use the remote operation
panel function.
Let the user make the password, and use SIM26-78 to set it.
MX-M503N MX-M283N/M363N/M363U/M453N/M453U/M503N/M503U/M282N/M362N/M452N/M502N 1 – 9
Equipped condition
With the desk unit installed
When the finisher is installed
When the finisher is installed
When the finisher is installed
When the finisher is installed
When the exit tray unit (MX-TRX2)
is installed
(2) Remote operation panel function password setting
procedures
1) Enter the SIM26-78 mode.
2) Enter the password with 10-key. (Within 5 - 8 digits)
The entered password is displayed on the column of "NEW."
To modify the entered password, use clear key to delete the
password digit by digit.
3) Press [SET] key, and the password is set.
N. USB PORT selection
There are two USB ports; one on the front frame side and the other
on the rear frame side. Only one of them can be used at a time. Do
not connect the two USB ports simultaneously.
When shipping, the port on the front frame side is valid and the port
on the rear frame side is invalid. When using the USB port, be care-
ful of the total current consumption not to exceed 500mA.
The valid port can be switched by changing the setting of the MFP
PWB DIP SW.
Select the valid USB port according to the user's request.
* The default setting for SW1/SW2 is OFF.
MFP PWB DIP SW
SW 1 SW 2
OFF OFF
OFF ON
NOTE: For the machine which is provided with a keyboard, either
one of two USB ports can be used at a time. However, both
DIP SW1's must be set to OFF.
Note that, if DIP SW1 is set to ON, the machine is set to the
CN update mode.
NOTE: After completion of option installation, revise all the firm-
ware to the latest version.
USB I/F
Port on the front Port on the rear
frame side frame side
Valid Invalid
Invalid Valid
Upper side: DIP-SW1
Lower side: DIP-SW2
When tilted toward you: OFF
When tilted to the PWB side: ON