Video Setup - Denon DBP-4010UDCI Owner's Manual

ENGLISH
;"
"
(~
I
Setting contents
16:9 Squeeze Auto: Output to a wide screen TV For 4:3 video. display in
the center of the screen without changing the aspect ratio.
*
1
WIDE (16:9) : Output to a wide screen TV
4:3 PS : Output to a 4:3 TV For wide video, trim the left and right side of
the image and display in 4:3 aspect ratio.
*
2
4:3 LB :
Output to a 4:3 TV Display all of the wide video.
480/576j, 480/576P, 720P. 1080i.
Source Direct:
Output video using its source resolution. Convert the
1080p video source to 1080i.
Aut2 : Detect the type of video material and automatically switch the
mode. Normally, this setting is used.
Video1 : Suitable for playing video material discs.
Video2: Suitable for playing video material discs or 30-frame film material
discs.
Video Setup Defalllt~s
are underlined.
Setting items
TV
Aspect (Aspect ratio)
Set the screen type and
display mode of the TV
Progressive Mode
Set an appropriate
progressive conversion
mode for the source video
material.
Component Resolution
*
3
Set the component output
resol ution.
TV Active Area
E.uU :
Set when a home-use monitor is connected.
Sets the horizontal display Normal: This setting is used when video synchronization is disturbed on
range when the analog a professional-use monitor.
video output resolution is
480i/576i. ' This is not available for HDMI output.
*
1 :This has no effect with the video and S-Video outputs.
*
2 : Depending on the video content, even though you set the 4:3 PS (Pan Scan). the content may be
output in 4:3 LB (Letter Box).
*
3 :When video is output from the HDMI terminal, no video signals are output from the component
terminals.
~iJ]
Sot 'h. vld.o o",po' ,1...1,"",dlo.
'0
tho '"o.....d TV
HDMI Setup
Setting contents
[Multi LPCM BM Off] : Decoded Linear PCM multi-channel signal is
output by the DBP-401 OUDCI. This setting is not made in speaker setting.
(BM: Bass Management)
[2ch] :
Output the downmixsed 2-channel LPCM signal.
The Super Audio CD audio signal is a 44.1 kHz/16-bit Linear PCM output.
• For the HDMI control function to operate, it is necessary for the DBP-
401 OUDCI or HOM I-compatible TV connected to the DBP-401 OUDCI to
have an HOM I connection.
• Refer to "HDMI Control Function" (iGf"page 47) for more information
about the HDMI control function.
• The HDMI control function from the connected device becomes valid
when. on the GUI menu. "DENON LINK Setup" - "DENON LINK Mode"
is set to "4th" (iGf" page 28).
• After the "HDMI Control" setting has been changed. always turn off the
power to the connected equipment and then turn it back on.
[Mute] :
Do not output audio from HOM I.
[Control]
• Off : Disable the HDMI control function.
• On : Link with the device connected to HOM I.
[Power Off Control]
• On : Turns the DBP-4010UDCI's power to standby through linkage to
the TV
• Off : Does not turn the DBP-4010UDCI's power to standby through
linkage to the TV
Setting items
Audio Setup
SA·CD Audio Out
On..: Super Audio CD audio is output.
Set to output stereo/multi
Off:
Super Audio CD audio is not output.
area audio of Super Audio ,
CD to the HDMI terminal.
HDMI Control
Can operate the unit in
conjunction with an HDMI
control support device.
'N·ji-
If you set "DENON LINK Setup" - "DENON LINK Mode" on the GUI menu to "4th". you will no longer
be able to change the "HDMI Control" - "Control" setting. To change the setting, switch "DENON LINK
Mode" to a setting other than "4th" first and then change the setting.
Remote control operation
buttons
SETUP
CD
.Displaying the menu
'Cancel the menu
.Moves the cursor
'(Up/Down/Left/Rightl
6)
:Decision the setting
RETURN
o
:Return to previous menu
24