Rear Panel - Sony HXCU-FB70 Operating Instructions Manual

Rear Panel

a "Memory Stick" slot
For service use only.
b
LAN jack (RJ-45, 8-pin)
Connects to a LAN hub (10BASE-T/100BASE-TX), when
using a network connection, via a LAN cable (shielded type,
category 5 or higher).
CAUTION
For safety, do not connect the connector for peripheral device wiring
that might have excessive voltage to this port. Follow the instructions
for this port.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur pour le
câblage de périphériques pouvant avoir une tension excessive à ce
port. Suivez les instructions pour ce port.
VORSICHT
Aus Sicherheitsgründen nicht mit einem Peripheriegerät-Anschluss
verbinden, der zu starke Spannung für diese Buchse haben könnte.
Folgen Sie den Anweisungen für diese Buchse.
c REMOTE connector (8-pin)
Transmits and receives control signals from the RCP-1000-
series Remote Control Panel via a CCA-5 cable (optional). It
also supplies power when connected to an RCP-1000-series
Remote Control Panel.
d Pr/R/R-Y, Y/G/Y, Pb/B/B-Y (component signals)
connectors (BNC type)
Outputs the HD component signals, SD component signals,
HD RGB signals, or SD RGB signals from the corresponding
connectors.
e RETURN INPUT SDI1, SDI2, VBS1, VBS2 (VBS/SDI
return video) connectors (BNC type)
Inputs the VBS return video signals (2-system), HD SDI or SD
SDI return video signals (2-system).
f AUDIO OUTPUT CH-1, CH-2 connectors (XLR 3-pin)
Outputs audio signals from the camera AUDIO 1 IN and
AUDIO 2 IN connectors.
g CAMERA connector (optical fiber connector)
Connects the CCU to the CA-FB70 HD Camera Adaptor using
an optical composite cable. When you use an optical
composite cable for connection, power supply, all camera
signals, such as control signal, video signal and audio signals
can be transmitted. When you use only single-mode optical
fiber cables for connection, all signals (except power supply)
can be transmitted by a pair of single-mode optical fiber
cables.
For information on pin assignment, see "CAMERA" in "Pin
assignment" on page 35.
Note
If the terminations of the single-mode optical fiber cable or optical
composite cable are contaminated with dust, etc., transmission errors
can occur. Be sure to replace the cap that came with the cable over
the termination when a cable is not in use.
CAUTION
CAMERA connector is non LPS (Limited Power Source) circuit. This
connector is connected to the CA-FB70.
ATTENTION
Le connecteur CAMERA n'est pas un circuit LPS (Limited Power
Source). Ce connecteur est raccordé au CA-FB70.
VORSICHT
Der Anschluss CAMERA ist ein Nicht-LPS-Schaltkreis (LPS: Limited
Power Source, Spannungsversorgung mit begrenzter Leistung).
Dieser Anschluss wird mit der CA-FB70 verbunden.
h AC supply input connector
Connects to the AC supply via the specified power cord
(optional). A plug holder (optional) can be used to secure the
power cord to the CCU.
i REFERENCE (reference input) connectors (BNC type)
IN: Inputs an HD tri-level reference sync signal or SD
reference sync signal (black burst signal) for external sync.
OUT: The input signal is output from the other connector as-is
(loop-through output). If the loop-through output is not
used, it is automatically connected to a 75 Ω terminator.
j PROMPTER (teleprompter input) connectors
(BNC type)
IN: Inputs the VBS signal for the teleprompter.
OUT: The input signal is output from the other connector as-is
(loop-through output). If the loop-through output is not
used, it is automatically connected to a 75 Ω terminator.
k S-VIDEO OUTPUT connector (4-pin)
Outputs S-VIDEO signal.
Locations and Functions of Parts
13