Siemens RDE series Operating Instructions page 2

'R \RX ZDQW WR HQWHU \RXU RZQ GD\ VZLWFKLQJ
SDWWHUQ"
A switching pattern consisting of 24 vertical pairs of
segments can be entered for every weekday. Each pair
represents a period of one hour. This means that a
switching action can occur every 60 minutes.
Example:
Switching pattern with factory setting Mo - Fr
0 6 12 18
Automatic operating mode changeover takes place
according to such a switching pattern, provided the
operating mode selector ist set to position
Proceed as follows:
•
Press once to reach the entry mode
The current switching pattern for day 1
(Monday) will be displayed. The segments
at far left start flashing and the time of day
00:00 is displayed
•
Press to set the point in time where you
want to assign the operating mode
•
Assignment of the operating mode to a point
in time is made by pressing

•
Press or to save the setting and to
change to the next day
•
When entry of the 7-day switching pattern is
finished, press and the entry will be
saved
8hˆ‡v‚)
30 seconds after the last entry is made, the
controller will leave the entry mode. In that case,
the last switching pattern changes made will not
be saved!
CE1B3035en / 02.05.2000
'R \RX ZDQW WR DGMXVW WKH WLPH RI GD\"
Tr‡‡vtÇurÇv€rÂsÃqh’)
•
Press
The time display starts flashing
•
Press
•
Press
leave the entry mode
24
'R \RX ZLVK WR UHWXUQ WR WKH IDFWRU\ VHWWLQJV"
.
To reset, first press and hold the button
press the two buttons
simultaneously for 3 seconds. This means that
the switching times and setpoints will be reset to
their default values.
8hˆ‡v‚)
'HIDXOW
Temperature setpoint in normal operation:
YDOXHV
Temperature setpoint in energy saving mode:
Day/s
Mo (1) – Fr (5)
and
Sa (6) – Su (7)
To reset, first press and hold the button
buttons ('+','-') simultaneously for 3 seconds. All individual
settings will be reset to their standard values.
Subject to alteration
once
to set the required time
or to save the setting and to
, then
and ('+','-')
6yyÃvqv‰vqˆhyÆr‡‡vt†ÃvyyÃirÃ
y‚†‡Ä
20 °C
8 °C
Normal Energy saving
operation mode
6:00 – 8:00 h 22:00 – 6:00 h
17:00 – 22:00 h 8:00 – 17:00 h
7:00 – 22:00 h 22:00 – 7:00 h
, then press the two
'RHV WKH V\PERO DSSHDU RQ WKH GLVSOD\"
2QO\ ZLWK EDWWHU\SRZHUHG YHUVLRQV
When this symbol appears, you need to replace the
batteries within the next two weeks.
'R \RX ZDQW WR FKDQJH WKH EDWWHULHV"
2QO\ ZLWK EDWWHU\SRZHUHG YHUVLRQV
•
Get two new alkaline batteries type AAA, 1.5 V
•
Remove the battery holder, then the batteries, insert
the new batteries and replace the battery holder
&DXWLRQ 7KH VHWWLQJ GDWD DUH PDLQWDLQHG IRU
D PD[LPXP RI WKUHH PLQXWHV RQO\
•
Make certain the old batteries are disposed of
properly, in compliance with environmental
requirements
(QHUJ\ VDYLQJ WLSV ZLWKRXW VDFULILFLQJ FRPIRUW
•
Never allow room temperatures to exceed 21 °C
•
Move the operating mode selector to energy saving
mode, even if you are absent for short periods of
time only.
•
Air out the rooms for short periods of time only, but
properly, with the windows wide open
Siemens Building Technologies / Landis & Staefa Division