Advertisement
General
Your Emerson Ceiling Fan/Light Wall
Control consists of a wall mount transmitter
and a receiver. The SW102 transmitter
works in conjunction with the receiver. The
receiver is mounted under the fan ceiling
cover. The wall control is designed to
separately control your ceiling fan speed
and light intensity.
Code switches in the wall control and
receiver may be set in 16 different
positions. If your fan and light go on and off
without using your control, you may be
getting interference from other transmitters
such as garage door openers, car alarms
or security systems. To remedy this
situation, simply change the combination
code in your wall control and receiver.
(See Figure 2.)
Installation of Receiver
(Figure 1)
WARNING
!
To avoid possible electrical shock,
be sure electricity is turned off at the
main fuse or circuit breaker box
before installing the receiver.
1. After electricity has been turned off at
main fuse box or circuit breaker box,
remove the ceiling cover from the hanger
bracket.
2. Disconnect the supply wiring to the fan
by removing wire connectors. Do not
disconnect the green/bare ground wires.
3. Connect the black supply wire to the
receiver black wire (AC IN L). Connect
the white supply wire to the receiver
white wire (AC IN N). Use only listed wire
connectors
(supplied)
to
connections.
4. Connect the receiver white wire (TO
MOTOR N) to the fan white wire.
Connect the receiver red wire (TO
MOTOR L) to the fan black wire. Connect
the receiver blue wire (FOR LIGHT) to
the fan blue wire.
CAUTION: If no light exist on your
ceiling fan, cap the blue wire on the
receiver with a wire connector.
5. Push the connected wires up into the
junction
box and position the receiver in the
hanger bracket above the hanger ball. Lay the
antenna wire on top of the receiver.
6. Reinstall the ceiling cover and restore
electrical power to the circuit.
TO
AC SUPPLY
1 2 3 4
WHITE
RED
BLUE
RECEIVER
FAN HOUSING
BARE
GREEN/GROUND
RECEIVER
ANTENNA
CEILING
COVER
make
Figure 1
4
Setting Operating
Frequency of Wall
Control and Receiver
Your SW102 Fan/Light Wall Control and
Receiver have code switches which must
be set in one of 16 possible code
combinations. The four levers (numbered
1, 2, 3, and 4) on the switches are factory-
set in the ON (up) position. Change the
switch settings as follows:
1. Slide the four switch levers in the wall
control to your choice of ON (up) or
down positions. Use a ball-point pen or
small screwdriver and slide the levers
firmly up or down (Figure 2).
WHITE
2. In the receiver, slide the four switch
BLACK
levers to the same positions as set in the
BLUE
wall control. Make sure the levers on
both switches are in the same positions,
otherwise the fan will not operate.
LIGHT
ON
1
2
3
4
HANGER
BRACKET
RECEIVER SWITCH
LEVERS
HANGER
BALL
SW102 WALL
CONTROL
Figure 2
Battery Installation
Turning off wall switch is not
sufficient. To avoid possible
electrical shock, be sure electricity
is turned off at the main fuse or
circuit breaker box.
The SW102 Fan/Light Wall Control
transmits the command signals via
radio waves to the receiver installed in
the ceiling fan ceiling cover. The
receiver is required for the SW102 wall
control to function. Power for the
SW102 wall control comes from the 12V
battery, located in the wall control.
Replacement 12V battery recommended
are Duracell MN21 and Eveready A23.
1. Install the 12V battery (supplied) into
the wall control (Figure 3).
2. The SW102 wall control is supplied with
a white, ivory or almond color cover.
Choose the style that best suits your
needs and snap the cover onto the wall
control (Figure 3).
RECEIVER
ON
1
2
3
4
WALL CONTROL
LEVERS
HI
HI
LIGH T
MED
MED
LOW
LOW
FAN OFF
CODE
SWITCH
Figure 3
5
of Wall Control
WARNING
!
HI
HI
LIG HT
MED
MED
LOW
LOW
FAN OFF
WALL
12V BATTERY
CONTROL
COVER
SW102 WALL
CONTROL
Advertisement
