Key Refrigerator Dimensions; Assemble The Enclosure For The Refrigerator; Install The Lower And Upper Vents - Norcold N61X Installation Manual

Key Refrigerator Dimensions

These key refrigerator dimensions are for your reference as
necessary (See Art017).
Refrigerator cabinet width w/o trim - .47 in. max. ..................... 1
Refrigerator width overall w/ trim - 4.6in. ....................................2
Refrigerator cabinet to side trim - 0.80 in. ....................................3
Refrigerator cabinet height w/o trim..............................................4
N600 models - 52.85 in. max.
N800 models - 59.85 in. max.
Refrigerator height overall w/ trim.................................................5
N600 models - 54.5 in.
N800 models - 61.5 in.
Refrigerator cabinet to top/bottom trim - 0.9 in. .......................... 6
Enclosure wall to hinges - 1.10 in. ................................................7
Refrigerator cabinet to center of handles .....................................8
N600 models - 32.5 in.
N800 models - 39.5 in.

Assemble the Enclosure for the Refrigerator

1. Make sure the enclosure is 59.88 - 60.01 inches high for
N81X models or 52.88 - 53.01 inches high for N61X models x
23.50 - 23.63 inches wide x 24 inches deep.
. Make sure the floor is solid and level.
- The floor must be metal or a wood panel and extend the full
width and depth of the enclosure.
- The floor must be able to support the weight of the
refrigerator and its contents.
. Make sure there are no adjacent heat sources such as a
furnace vent, a hot water heater vent, etc.
4. If there is more than 1/ inch between either side of the
refrigerator and the inside of the enclosure:
- Fill the space with fiberglass insulation or add a baffle to
eliminate the excess clearance.
- Make sure that the rear of the batt-type insulation is
between 18 - 19 inches from the face of the enclosure.
- Securely attach the batt-type insulation to the enclosure
so that it remains in this position during refrigerator
installation, if it becomes wet, and in windy conditions.

Install the Lower and Upper Vents

1. Using the following chart, decide which vents and rough
opening (RO) sizes to use:
Certified Vent P/N
Upper Roof 69
Exhaust Cap
Installation Manual 4
RO Height RO Width
N/A N/A
Upper Roof 61619
Exhaust Vent
Lower Metal 616010
Intake
Upper Exhaust 61156
& Lower Intake
Plastic
. Install the lower intake vent (See Art01598, Art01599, and
Art0160):
NOTE: The lower intake vent is also the service access opening
for the components on the rear of the refrigerator.
!
WARNING:
Make sure the bottom of the opening of the
lower intake vent is even with or immediately below the
floor level. This allows any leaking propane gas to escape
to the outside and not to collect at floor level.
- Make sure the bottom of the opening of the lower intake vent
[9] is even with or immediately below the floor level.
- Align the lower intake vent vertically below the coils [10] and
the condenser [11] of the refrigerator.
. Install the upper exhaust vent:
!
CAUTION:
Make sure that no sawdust, insulation, or
other construction debris is on the refrigerator or in the
enclosure. Debris can cause a combustion hazard and
prevent the refrigerator from operating correctly.
NOTE: Tighten the screws of the upper roof exhaust cap to 10
inch-pounds max. Also make sure that the air flow
around the upper roof exhaust cap is not blocked or
decreased by other roof mounted features such as a
luggage carrier, an air conditioner, a solar panel, etc.
- If the design of the vehicle allows, install the roof exhaust
vent [1] directly above the condenser [11] of the refrigerator
(See Art01598).
- Install a baffle [1] to prevent stagnant hot air in the area
[14] above the refrigerator.
- Make sure there is less than 1/4 inch clearance
[715] between the baffle and the top of the
refrigerator.
- Make sure the baffle is the full width of the inside of
the enclosure.
- If the design of the vehicle does not allow you to install the
roof exhaust vent directly above the condenser [11] of the
refrigerator (See Art01599).
- Align the roof exhaust vent [1] above the condenser
[11] of the refrigerator and move it inboard as necessary.
4 in. 5 1/4 in.
1 5/8 in. 1 5/8 in.
1 /4 in. 1 1/ in.