Related Manuals for ZyXEL Communications UNS2300
Summary of Contents for ZyXEL Communications UNS2300
- Page 1 UNS2300 / UNS2700 Unified Network Storage Version 1.00 Edition 1, 06/2013 Quick Start Guide Hardware Installation Guide www.zyxel.com Copyright © 2013 ZyXEL Communications Corporation...
-
Page 2: Related Documentation
IMPORTANT! READ CAREFULLY BEFORE USE. KEEP THIS GUIDE FOR FUTURE REFERENCE. This guide shows you how to use the rack mounting kit to install the UNS in a rack. Graphics in this book may differ slightly from your product. Every effort has been made to ensure that the information in this manual is accurate. -
Page 3: Table Of Contents
H A PT ER Hardware Installation 1.1 Overview • Mount the UNS in a Rack on page 3 • Insert a Hard Drive on page 6 • About the Power Modules on page 8 • Make Rear Panel Connections on page 9 •... - Page 4 Chapter 1 Hardware Installation • Make sure the position of the UNS does not make the rack unstable or top-heavy. Take all necessary precautions to anchor the rack securely before installing the unit. 1.2.2 Separate the Slide Rails A slide rail consists of an inner rail and an outer rail. Release the lock (1) and slide out out the inner rail completely to separate the rails.
- Page 5 Chapter 1 Hardware Installation Screw the outer rail onto the side of the rack using the M6 screws and nuts. Repeat for the other side of the rack. 1.2.5 Insert the UNS into the Rack It is recommended that two people insert the UNS (with inner railings attached) into the rack. The inner rail (attached to the UNS) has two locks.
-
Page 6: Insert A Hard Drive
Chapter 1 Hardware Installation Use the screws to fasten the inner rail to the rack. Note: To remove the UNS from the rack, use the outer lock on the inner rail. 1.3 Insert a Hard Drive 1.3.1 Drive Tray Slot Numbering The drive trays (with hard drive) can be installed into any slot. - Page 7 Chapter 1 Hardware Installation Push the latch on the right (1) to release the front handle of the hard drive tray (2). Gently slide out the hard drive tray (3). This is the empty hard drive tray. Place a compatible hard drive into the hard drive tray as shown. Hard Drive Tray Turn the tray over while holding the hard drive inside and fasten the hard drive to the tray with the...
-
Page 8: About The Power Modules
Chapter 1 Hardware Installation Note: Make sure the screws are fastened tightly as protruding screws will impede insertion of the hard drive tray into the UNS. Put the hard drive tray back into the UNS by sliding it gently all the way in, and then closing the front. -
Page 9: Make Rear Panel Connections
If you want to remove a power module, use the handle (2) to slowly pull it out with one hand and place the other hand under it to support it. 1.5 Make Rear Panel Connections The following is the rear panel for the UNS2700. The following is the rear panel for the UNS2300. UNS Series Hardware Installation Guide... -
Page 10: Turn On The Uns
Connect the UNS to a 1G device in your network (computer, switch, router, and so UNS2700 and 2-6 on on) using an Ethernet cable. This port can operate at 10/100/1000 Mbps speeds UNS2300 and is not VLAN-aware. 10G Ports - 3, 4 on... - Page 11 Chapter 1 Hardware Installation • Power Module LEDS and Buzzer • UNS Power Switch LEDs • UNS Port LEDs 1.7.1 Hard Disk Tray LEDs The LEDs are to the right of the latch. The following table describes the LEDs on the hard disk tray. Table 2 Hard Disk Tray LEDs COLOR STATUS...
- Page 12 Chapter 1 Hardware Installation The following table describes the LEDs and buzzer on the power module. Table 3 Power Module LEDs and Buzzer LED/BUTTON COLOR STATUS DESCRIPTION Green The power module is receiving AC power. Blinking This power module is not receiving AC power. Both power modules are not receiving AC power.
- Page 13 1.7.4 UNS Port LEDs On the UNS2700, ports 1 and 2 are 1 Gbps ports; ports 3 and 4 are 10 Gbps ports. On the UNS2300, ports 1-6 are 1 Gbps ports. The following table describes the Ethernet port LEDs.
-
Page 14: Accessing The Uns
Chapter 1 Hardware Installation Table 5 Ethernet Port LEDs (continued) COLOR STATUS DESCRIPTION 1G - Green The 1G port is connected at 100 Mbps. Connection Yellow The 1G port is connected at 1000 Mbps. /Speed (Right) The 1G port is connected at 10 Mbps or there is no connection. 10G - Green The 10G port is connected at 10000 Mbps. - Page 15 Chapter 1 Hardware Installation The main screen appears. This table describes the fields in the UNS Finder. Table 6 UNS Finder LABEL DESCRIPTION Rescan Click this to have the UNS Finder search again for UNS devices in your network. About Click this to get more information on this UNS Finder release.
-
Page 16: Configure The Uns Using The Web Configurator
Chapter 1 Hardware Installation 1.9 Configure the UNS Using the Web Configurator The web configurator is a HTML-based program you use to configure the UNS with your web browser. The default login name and password is ‘admin’ and ‘1234’. Use the menus on the left to configure the UNS. See the User’s Guide or the web help to find more information on these screens. - Page 17 Chapter 1 Hardware Installation Refer to the table below to choose a RAID. Table 7 RAID Description TYPE DESCRIPTION RAID 0 Disk striping. RAID 1 Disk mirroring over two disks. RAID 5 Striping with interspersed parity over the member disks. RAID 6 2-dimensional parity protection over the member disks.
Need help?
Do you have a question about the UNS2300 and is the answer not in the manual?
Questions and answers