Advertisement
Quick Links
THIS MANUAL IS FOR THE FOLLOWING PRODUCTS:
HCAA60**, HCAA61** and HCAA62**
Hobbico
®
guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty
does not cover any component parts damaged by use or modification. In no case shall Hobbico's liability exceed the original cost
of the purchased kit. Further, Hobbico reserves the right to change or modify this warranty without notice.
In that Hobbico has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-
assembled product, the user accepts all resulting liability.
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit
immediately in new and unused condition to the place of purchase.
READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT
INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.
© Copyright 2003
WARRANTY
See more of our products at www.hobbico.com
Engine: O.S. 40 LA (.40 cu in [6.5cc] two-stroke)
Champaign, Illinois
(217) 398-8970, Ext. 5
airsupport@hobbico.com
HCAZ3040 for HCAA60**, HCAA61**, HCAA62** V1.0
™
Wingspan: 60 in [1525mm]
Wing Area: 660 sq in [43 dm
Weight: 5.5 lbs [2490 g]
Wing Loading: 19 oz/sq ft [58 g/dm
Length: 49 in [1245mm]
Radio: Futaba 4VF
2
]
2
]
Advertisement
Related Manuals for Hobbico HCAA60 series
Summary of Contents for Hobbico HCAA60 series
- Page 1 Further, Hobbico reserves the right to change or modify this warranty without notice. In that Hobbico has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user- assembled product, the user accepts all resulting liability.
-
Page 2: Field Equipment
Do not alter or modify the model, as doing so may result in an unsafe or unflyable model. In a few cases the instructions may Congratulations and thank you for purchasing the Hobbico differ slightly from drawings or sketches. In those instances the SuperStar MKII .40 Select. - Page 3 Assemble the Fuselage Assembly Charge the Batteries 1. In the fuselage (fuse), connect the plug from the battery pack, labeled “BATTERY 1”, to the plug from the on/off switch, labeled “BATTERY 2.” 2. As shipped, the rechargeable batteries in the SuperStar MKII are only partially charged.
- Page 4 3. Connect the elevator pushrod to the fourth hole out from the base of the control horn on the elevator control horn. 6. Fit the spinner back plate, followed by the prop, prop Connect the rudder pushrod to the second hole out from the washer and prop nut, on the engine.
- Page 5 Center the Controls Note:We strive to maintain constant quality control in order that your new SuperStar MKII Select will be pre-adjusted properly. Please be sure to check these adjustments on your airplane as instructed below in order to guarantee that your first flight will be a pleasant experience.
- Page 6 not fully closed, loosen the screw on the screw-lock connector on the throttle servo arm and move the pushrod forward until the carburetor is closed. Securely tighten the screw. 4. Center the nose wheel by adjusting the pushrod in the screw-lock pushrod connector on the rudder servo.
- Page 7 Set the Control Throws Identify Your Model The control throws are a measure of how far the flight controls Whether you fly at an R/C club or somewhere on your own, you move up and down (or from side to side). If the controls move should have your name, telephone number and address in or too much, the plane will respond too quickly and be difficult to on your model so it can be identified and returned in case it...
-
Page 8: Flight Preparation
If additional weight is required to balance the plane, purchase Flight Preparation Great Planes Self Adhesive Lead Weights (GPMQ4485). If adding tail weight, stick the weight to the side of the fuse under Flight preparation is to be done at the flying field. the stab. - Page 9 Range Check the Radio correct the nose wheel because this will also affect the rudder. Note: Crosswinds may affect the direction the model rolls, so A range check must be performed before the first flight of a this test should be done in calm conditions, or with the model new model.
- Page 10 After you have landed and shut the engine off, adjust the pushrods Ordering Replacement Parts on the ailerons, elevator and rudder as necessary so the trim levers on the transmitter may be returned to center (this will not be To order replacement parts for the SuperStar MKII .40 Select, required on any of the controls that did not need trim adjustments).
- Page 11 Photo-illustrated instructions pave the way for rapid progress through the last few assembly steps to that fantastic first flight! If you don’t have a lot of time to spare, Hobbico also offers the Avistar 40 Select. You can complete ALL assembly within 20 minutes, using a screwdriver and pliers.
-
Page 12: Building Notes
BUILDING NOTES Kit Purchased Date: _______________________ Date Construction Finished: _________________ Where Purchased:_________________________ Finished Weight: __________________________ Date Construction Started: __________________ Date of First Flight: ________________________ FLIGHT LOG...
Need help?
Do you have a question about the HCAA60 series and is the answer not in the manual?
Questions and answers