Hobbico Flyzone HCAA0235 Assembly

ASSEMBLY OF YOUR ELECTRIC FREE-FLIGHT SPITFIRE

WARNING: Read instructions carefully! Improper use of this product may result in personal injury or damage to the public.
WARNING: Choking hazard - Small parts. Not for children under 3 years. Use with adult supervision.

INSTALL THE MAIN WINGS

Top of
Wing
CONTROL SURFACE
Bottom
WING
of Wing
BRACE
CENTERLINE
• Remove the backing paper from the double sided tape on
the fuselage.
• Attach the main wings to the bottom of the fuselage by lining
them up along the centerline of the fuselage. Make sure you are
able to see the screw holes between the wings. (see drawing)
• When attaching the main wings to the fuselage, the airplane will
be upside down. The wing brace will be upwards only during
assembly.The control surfaces need to face the tail of the plane.
1. Remove the back cover of the charger
and install 4 "AA" batteries according to the
diagram in the charger. Put the cover back
on the charger. CAUTION: Do not use
rechargeable (nickel cadmium) batteries.
Do not mix old and new batteries. Do not
mix alkaline, standard (carbon zinc), or
rechargeable (nickel cadmium) batteries.
2. Before charging your free flight Spitfire,
make sure the "on-off" switch is in the
"off" position.
3. Insert the charger into the charge
socket on the side of the Spitfire. The
charger will only fit one way so match the
tab on the charger with the notch on the
charge socket.

WARRANTY

Hobbico, Inc. guarantees this kit to be free of defects in both material and workmanship at the date of purchase. This warranty does not cover
any component parts damaged by use or modification. In no case shall Hobbico's liability exceed the original cost of the purchased kit. Further,
Hobbico reserves the right to change or modify this warranty without notice. In that Hobbico has no control over the final assembly, no liability
shall be assumed nor accepted for any damage resulting from the use of the final user-assembled product. By the act of using the user-
assembled product the user accepts all resulting liability. If the buyer is not prepared to accept the liability associated with the use of this
product, the buyer is advised to immediately return this kit in new and unused condition to the place of purchase.
Entire Contents © Copyright 2001
™
Requires 4AA Alkaline batteries
HCAA0235
(Not included)
WING
DOUBLE-SIDE
TAPE
FUSELAGE
SCREW
HOLES
ON/OFF
SWITCH
Replacement Parts HCAP9902 Charger
• Install the propeller on the airplane by firmly grasping the
airplane's fuselage and pushing the propeller onto the motor
shaft. Be sure the propeller is fully seated on the shaft.
• Note: The front of the wing cover is thicker than the back. The
thicker end goes to the front, closest to the propeller.
• Line up the holes in the wing cover and the fuselage. If the
thicker part of the cover is not placed to the front, the screw
holes will not line up.
• Carefully place the screws through the holes securing the
wing cover to the fuselage.
• Tighten the screws securely...DO NOT OVER TIGHTEN.
• Using the box photo as a guide, apply the decals to
your Spitfire.

CHARGING

CHARGE
CONNECTOR
CHARGER
HCAQ3278 Propeller (2)
HCAA3270 Wing / Tail Assembly

INSTALL THE PROPELLER

INSTALL THE WING COVER

WING
COVER
WING
BRACE

APPLYING THE DECALS

4. On the first charge, only charge the
Spitfire for 15 seconds. For longer flights,
you may increase the charge time up to
60 seconds.
5. Never charge the Spitfire for more than
60 seconds. If you do, you may overheat
the batteries in the Spitfire or the charger
and damage them.
6. When charging is complete, remove
the charger from the Spitfire
CAUTION: Keep fingers, face, clothing
and other objects away from the propeller
when running.
HCAZ3035 for HCAA0235