Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE:A NOTE indicates important information that helps you make better use of your computer system.
Page 5
The wall socket shall be installed near the equipment and shall be easily accessible. For use only with the attached power adapter which have CE,UL,CSA listed license (Only for monitors with power adapter). Factory: TPV ELECTRONICS(FUJIAN) CO., LTD P2479VW8 Model:ADPC1925EX:19VDC 1.3A; P2479VWM8 Model:ADPC1938EX:19VDC 1.84A;...
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product.
Page 7
Cleaning Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Page 8
Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation.
Contents in Box Warranty card Adapter Power Cable DVI Cable Analog Cable HDMI Cable MHL Cable Not all signal cables (Analog,DVI,HDMI,MHL ) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Adjusting Viewing Angle For optimal viewing, it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle as below.
Connecting the Monitor Cable Connections In Back of Monitor and Computer: P2479VWM8 P2479VW8 DC port D-SUB HDMI-2/MHL HDMI-1/MHL Earphone To protect equipment, always turn off the PC and LCD monitor before connecting. Connect the power cable to the DC port on the back of the monitor.
Adjusting Setting Optimal Resolution Windows 8 For Windows 8: Right click and click All apps at the bottom-right of the screen. Set the “View by” to “Category”. Click Appearance and Personalization.
Page 14
Click DISPLAY. Set the resolution SLIDE-BAR to Optimal preset resolution.
Double click DISPLAYA Click SETTINGS Set the resolution SLIDE-BAR to Optimal preset resolution. Windows ME/2000 For Windows ME/2000: Click START. Click STTINGS. Click CNTROL PANEL. Double click DISPLAYA. Click SETTINGS 6. Set the resolution SLIDE-BAR to Optimal preset resolution.
Clear Vision When there is no OSD, Press the “<” button to activate Clear Vision. Use the “<” or “>” buttons to select between weak, medium, strong, or off settings. Default setting is always “off”. Press and hold “<” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo: on”...
Using “MHL(Mobile High-Definition Link)” “MHL” (Mobile High-Definition Link) This feature allows you to enjoy videos and photos(imported from a connected mobile device that supports MHL) on the screen of the product. To use the MHL function, you need an MHL-certified mobile device. You can check if your mobile device is MHL certified on the device manufacturer’s website.
OSD Setting Basic and simple instruction on the control keys. Press the MENU-button to activate the OSD window. Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate. Press < or > to navigate through the sub-menu. Once the desired function is highlighted, press MENU-button to activate.。...
Luminance MENU(Menu) to display menu. Press MENU Press < or > to select (Luminance), and press to enter. MENU Press < or > to select submenu, and press to enter.
Page 26
Press < or > to adjust. Press AUTO to exit. Brightness 0-100 Backlight Adjustment. Contrast 0-100 Contrast from Digital-register. Standard Standard Mode. Text Text Mode. Internet Internet Mode. Eco mode Game Game Mode. Movie Movie Mode. Sports Sports Mode. Gamma1 Adjust to Gamma 1.
Image Setup MENU Press (Menu) to display menu. MENU Press < or > to select (Image Setup), and press to enter.。 MENU Press < or > to select submenu, and press to enter.
Page 28
Press < or > to adjust. Press AUTO to exit.。 Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Phase 0-100 Adjust Picture Phase to reduce Horizontal-Line noise. Sharpness 0-100 Adjust picture sharpness. H.Position 0-100 Adjust the horizontal position of the picture. V.Position 0-100 Adjust the vertical position of the picture.
Color Setup MENU Press (Menu) to display menu. MENU Press < or > to select (Color Setup), and press to enter。 MENU Press < or > to select submenu, and press to enter.
Page 30
Press < or > to adjust. Press AUTO to exit. Recall Warm Color Temperature from Warm EEPROM. Recall Normal Color Temperature from Normal EEPROM. Recall Cool Color Temperature from Cool EEPROM. Color Temp. Recall SRGB Color Temperature from sRGB EEPROM. Red Gain from Digital-register User Green...
Picture Boost MENU Press (Menu) to display menu. MENU Press < or > to select (Picture Boost), and press to enter. MENU Press < or > to select submenu, and press to enter.。...
Page 32
Press < or > to adjust. Press AUTO to exit. Bright Frame ON/OFF Disable or Enable Bright Frame. Frame Size 14-100 Adjust Frame Size. Brightness 0-100 Adjust Frame Brightness. Contrast 0-100 Adjust Frame Contrast. H. position 0-100 Adjust Frame horizontal position. V.
OSD Setup MENU Press (Menu) to display menu. MENU Press < or > to select (OSD Setup), and press to enter. MENU Press < or > to select submenu, and press to enter.。...
Page 34
Press < or > to adjust. Press AUTO to exit.。 Language Adjust the horizontal position of OSD. Timeout 5-120 Adjust the vertical position of OSD. H. Position 0-100 Adjust the OSD Timeout. V. Position 0-100 Adjust the transparence of OSD. Transparence 0-100 Select the OSD language.
Other MENU Press (Menu) to display menu. MENU Press < or > to select (Extra), and press to enter.。 MENU Press < or > to select submenu, and press to enter.。...
Page 36
Press < or > to adjust. Press AUTO to exit. Auto/D-SUB/DVI Select input signal source. (P2479VW8) Input Select Auto/D-SUB/HDMI1/MHL1/H Select input signal source. (P2479VWM8) DMI2/MHL2 Auto Config. Yes/No Auto adjust the picture to default. Off Timer 0-24 hrs Select DC off time.
Adjusting Setting Optimal Resolution Windows 8 For Windows 8: Right click and click All apps at the bottom-right of the screen. Set the “View by” to “Category”. Click Appearance and Personalization. Click DISPLAY.
Page 40
Set the resolution SLIDE-BAR to Optimal preset resolution。 點擊“高級設置”按鈕。...
Page 41
Click the “Monitor” tab and then click the “Properties” button. Click the “Driver” tab. 10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button.
Page 42
11. Select "Let me pick from a list of device drivers on my computer". 12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive).。 13.
Windows 7 For Windows 7 Click on the 'Start' button and then click on 'Control Panel'.。 Click on the 'Display' icon. Click on the “Change display settings” button.
Page 44
Click the “Advanced Settings” button.。 Click the “Monitor” tab and then click the “Properties” button. Click the “Driver” tab.
Page 45
Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. Select "Let me pick from a list of device drivers on my computer".。 10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive).
Page 46
11. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button. 12. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk drive. 13. Close all open windows and remove the CD. 14.
Windows Vista Click "Start" and "Control Panel". Then, double-click on "Appearance and Personalization". Click "Personalization" and then "Display Settings". Click "Advanced Settings...".
Page 48
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Click "Update Driver..."...
Windows XP Start Windows XP Click on the “Start” button and then click on “Control Panel”. Select and click on the category “Appearance and Themes”. 4. Click on the “Display” Item...
Page 50
5. Select the “Settings” tab then click on the “Advanced” button. Select “Monitor” tab - If the “Properties” button is inactive, it means your monitor is properly configured. Please stop installation. - If the “Properties” button is active, click on “Properties” button. Please follow the steps below.
Page 51
8. Select the “Install from a list or specific location [advanced] ” radio button and then click on the “Next” button. 9. Select the “Don't Search. I will choose the driver to install” radio button. Then click on the “Next” button. 10.
dialog box. Click on the “OK” button and then the “OK” button again to close the Display Properties Windows 2000 1. Start Windows® 2000 Click on the “Start” button, point to “Settings”, and then click on “Control Panel”. Double click on the “Display” Icon. Select the “Settings”...
i-Menu Welcome to “i-Menu” software by ENVISION. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide.
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).
Screen+ Welcome to "Screen+" software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop nto different panels, and each panel displays a different window. You only need to drag the window to a corresponding pane, when you want to access it. It supports multiple monitor display to make your task easier.
Troubleshoot Problem & Question Possible Solutions Make sure the power button is ON and the Power Cord is properly connected Power LED Is Not ON to a grounded power outlet and to the monitor. Is the power cord connected properly? Check the power cord connection and power supply.
Page 57
The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor's video cable is properly connected to the computer. Monitor Is Stuck In Active Inspect the monitor's video cable and make sure no pin is bent. Off-Mode"...
Specification General Specification(P2479VW8) Model name P2479VW8 Driving system TFT Color LCD Viewable Image Size 59.8cm diagonal Pixel pitch 0.2715(H)mm x 0.0905(V)mm LCD Panel Video R, G, B Analog lnterface & Digital Interface Separate Sync. H/V TTL Display Color 16.7M Colors Pixel Clock 148.5 MHz...
General Specification(P2479VWM8) P2479VWM8 Model name Driving system TFT Color LCD Viewable Image Size 59.8cm diagonal Pixel pitch 0.2715(H)mm x 0.0905(V)mm LCD Panel Video R, G, B Analog lnterface & Digital Interface Separate Sync. H/V TTL Display Color 16.7M Colors Pixel Clock 165 MHz Horizontal scan range 30KHz ~ 83KHz...
Pin Assignments 15- Pin Color Display Signal Cable Pin Number Signal Name Pin Number Signal Name Video-Red Video- Green Ground Video- Blue N.C. N.C. DDC-Serial data Detect Cable H-sync GND-R V-sync GND-G DDC-Serial clock GND-B 24-Pin Color Display Signal Cable Pin Number Signal Name Pin Number...
Page 63
19- Pin Color Display Signal Cable Pin No.. Signal Name Pin No. Signal Name TMDS Data2+ TMDS Data SShiel TMDS Data 2 SShiel TMDS Clock TMDS Data 2- eserved (N. C. on devic) TMDS Data 1+ TMDS Data 1 SShiel TMDS Data 1- TMDS Data 0+ DDC/CEC Ground...
Plug and Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
Regulation FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
WEEE Declaration This symb Disposal of Waste Equipment by Users in Private Household in the European Union. This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
Page 67
This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Energy Star ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) BV and Envision Peripherals, Inc. have determined that this product meets the ENERGY STAR® guidelines for energy efficiency. (FOR EPA CERTIFIED MODELS)
The freight cost for the warranty is pre-paid by AOC for the delivery and return. Please ensure you provide a dated proof of purchase along with the product and deliver to the AOC Certified or Authorized Service Center under the following condition: •...
Page 70
If your warranty has expired, you still have access to all available service options, but you will be responsible for the cost of service, including parts, labor, shipping (if any) and applicable taxes. AOC Certified or Authorized Service Center will provide you with an estimate of service costs before receiving your authorization to perform service.
During this period, AOC International (Europe) B.V. offers a Carry-In (return to Service Center) Warranty Support at an AOC’s Authorized Service Center or Dealer and at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. As a Standard Policy,...
Page 72
• Repair, modification, or installation of options or parts by anyone other than an AOC Certified or Authorized Service Center • Improper environments like humidity, water damage and dusts • Damaged by violence, earthquakes and terrorist attacks • Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other...
No manufacturer can guarantee that all panels will be free from pixel defects, but AOC guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This Pixel Policy explains the different types of pixel defects and defines acceptable defect levels for each type.
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free number (888) 662-9888. Or you can request an RMA Number online at www.aoc.com/na-warranty. * This limited warranty does not cover any losses or damages that occur as a result of:...
Page 75
ARGENTINA: http://ar.aoc.com/support/find_service_center BOLIVIA: http://bo.aoc.com/support/find_service_center CHILE: http://cl.aoc.com/support/find_service_center COLOMBIA: http://co.aoc.com/support/find_service_center COSTA RICA: http://cr.aoc.com/support/find_service_center DOMINICAN REPUBLIC: http://do.aoc.com/support/find_service_center ECUADOR: http://ec.aoc.com/support/find_service_center EL SALVADOR: http://sv.aoc.com/support/find_service_center GUATEMALA: http://gt.aoc.com/support/find_service_center HONDURAS: http://hn.aoc.com/support/find_service_center NICARAGUA: http://ni.aoc.com/support/find_service_center PANAMA: http://pa.aoc.com/support/find_service_center PARAGUAY: http://py.aoc.com/support/find_service_center PERU: http://pe.aoc.com/support/find_service_center URUGUAY: http://pe.aoc.com/support/find_service_center VENEZUELA: http://ve.aoc.com/support/find_service_center IF COUNTRY NOT LISTED: http://latin.aoc.com/support/find_service_center...
Tube & LCD Panel) *AOC will need to obtain a credit card number if you would like to get a new AOC monitor advanced shipped to your location, prior to the defective unit arriving at AOC’s service center. If you do not wish to supply a credit card, AOC will only ship the new monitor, once the defective unit arrives at the AOC service center.