Advertisement
Quick Links
Electronic Service
Manuals
This electronic document is provided as a service to our custom-
ers. We do not create the contents of the information contained in
this document. Should you have detailed questions pertaining to
the information contained in this document, you may contact Michco,
or the manufacturer which provided the original information in this
electronic deliverable. Michco's only part in this electronic deliver-
able was the electronic assembly process.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339 MI, OH, IN only
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: CustServ@Michco.com
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email:
Shop@Michco.com
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective
owners. Manuals are subject to Manufacturer's reproduction limitations. Originals or reproductions were provided
by manufacturers through a request. We make no warranty as to the correctness of information provided in this
document and you assume all risk.
Advertisement
Related Manuals for Nilfisk-Advance Kent 56302300
Summary of Contents for Nilfisk-Advance Kent 56302300
- Page 1 Electronic Service Manuals This electronic document is provided as a service to our custom- ers. We do not create the contents of the information contained in this document. Should you have detailed questions pertaining to the information contained in this document, you may contact Michco, or the manufacturer which provided the original information in this electronic deliverable.
- Page 2 OPERATOR Kent SelectScrub 17 Model 56302300 3/99 Form Number 56041433...
-
Page 3: Table Of Contents
Cautions and Warnings ..........4 Introduction ............... 6 Know Your Machine ..........6 Prepare the Machine For Use ........6 Machine Operation ............ 7 After Use ..............7 Maintenance Schedule..........8 Charging the Batteries ..........8 Squeegee Cartridge Rotation........8 Battery Condition Indicator ........ - Page 4 FRONT FORM NO. 56041433 / SELECTSCRUB 17 - 3...
-
Page 5: Cautions And Warnings
CAUTIONS AND WARNINGS SYMBOLS Kent uses the symbols below to signal potentially dangerous conditions. Read this information carefully and take the necessary steps to protect personnel and property. DANGER! Is used to warn of immediate hazards that will cause severe personal injury or death. WARNING! Is used to call attention to a situation that could cause severe personal injury. - Page 6 CONSIGNES DE SÉCURITÉ SYMBOLES Les symboles ci-dessous sont utilisés pour signaler des conditions d’emploi qui présentent un danger. Lisez ces informations avec soin et prenez les mesures nécessaires de protection des personnes et des biens. DANGER! avertit de dangers immédiats causant des blessures graves ou la mort. ATTENTION! attire l’attention sur une situation pouvant causer des blessures graves aux personnes.
-
Page 7: Introduction
INTRODUCTION PREPARE THE MACHINE FOR USE This manual will help you get the most from your Kent SelectScrub 17. Read B - INSTALLING THE BATTERIES it thoroughly before operating the machine. WARNING! Note: Bold numbers in parentheses indicate an item illustrated on page 2 (Figure A). -
Page 8: Machine Operation
INSTALLING THE BRUSH OR PAD HOLDER CAUTION! WARNING! To avoid damaging the floor, keep the machine moving while the brush is turning. Moving parts - turn the Solution Switch (15), Brush Switch (13) Re-adjust the Solution Flow Control Lever (16) so a thin , even layer and Vac Switch (14) OFF and disconnect the Battery Connector of solution can be seen in front of the Squeegee Assembly (8). -
Page 9: Maintenance Schedule
MAINTENANCE SCHEDULE CHECKING THE BATTERY WATER LEVEL Maintenance Item Daily Weekly Monthly Yearly Check the water level of the batteries at least once a week. Clean the Recovery Tank After charging the batteries, remove the vent caps and check the water level Clean the Float Screen in each battery cell. -
Page 10: Battery Condition Indicator
D - BATTERY CONDITION INDICATOR OPERATION TROUBLESHOOTING POOR WATER PICKUP To operate, the Brush Switch (13) or the Vac Switch (14) must be turned on to activate the Battery Condition Indicator (19) to determine the charge condition Recovery tank full, float shut-off closed of the battery pack. - Page 11 Nilfisk-Advance, Inc. 14600 21st Avenue North Plymouth, MN, 55447-3408 www.nilfisk-advance.com Phone: 800-989-2235 Fax: 800-989-6566 ©2000 Nilfisk-Advance, Inc., Plymouth, MN 55447-3408 Printed in the U.S.A.