Advertisement
SAN REMO STOVES
4,6,8,12 and 16kW
FREESTANDING
WOOD BURNING
STOVES
Installation and Operating
Instructions
Please hand these instructions to the stove user when the installation
is complete. Leave the system ready for operation and instruct the
user in the correct use of the appliance and operation of controls.
Installation – Must be installed by a qualified plumber or suitably
qualified fitter
HD01 18/12/11
Advertisement
Table of Contents
Summary of Contents for San Remo Stoves 4kW
- Page 1 SAN REMO STOVES 4,6,8,12 and 16kW FREESTANDING WOOD BURNING STOVES Installation and Operating Instructions Please hand these instructions to the stove user when the installation is complete. Leave the system ready for operation and instruct the user in the correct use of the appliance and operation of controls.
-
Page 2: Assembly Instructions
Assembly Instructions PLEASE READ THESE INSTRUCTIONS CAREFULLY It is important that your stove is correctly installed, as San Remo Stoves cannot accept responsibility for any fault arising through incorrect installation. 1. Your San Remo Stove comes 2. Remove the plastic bag and packed in a plywood crate. - Page 3 6. Fit the Flue Collar using the 4-M6 set screws and washers supplied. Screw The M6 nuts on the M6 screws all the way to the end. Then put the washer over the screw/nut assembly and secure the collar to the lid/back as desired. The flue collar is shown below fixed to the top of the stove.
-
Page 4: List Of Components
List of Components Description of Parts Door Handle Airwash Control Handle Primary Air Caps Riddling Handle Ash Pan Ash Pan Tool Coal Guard Baffle Plate Legs Leg Height Screws M17 Leg Screws M14 Leg Washers Flue Collar Flue Collar Screws M10 Flue Collar Nuts M10 Flue Collar Washers HD01 18/12/11... -
Page 5: Installation Instructions
Installation Instructions READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION These instructions cover the basic principles to ensure satisfactory installation of the stove, although detail may need slight modification to suit particular local site conditions. In all cases the installation must comply with National and European Building Regulations, Local Authority Byelaws and other specifications or regulations as they affect the installation of the stove. - Page 6 The diameter of the flue should not be less than 125mm and not more than 200mm. If any of these requirements are not met, the chimney should be lined by a suitable method. The chimney must be swept before connection to the stove. Where the chimney is believed to have previously served an open fire installation, it is possible that the higher flue gas temperature from the stove may loosen deposits that were previously firmly adhered, with the consequent risk of flue blockage.
-
Page 7: Operating Instructions
Care should be taken to level the stove using the adjusting screws in the feet. The appliance shall be installed on a floor with adequate load-bearing capacity. If the existing construction does not meet this prerequisite, suitable measures (e.g. load disturbing plate) should be taken to achieve it. - Page 8 Air Controls This stove has been designed to burn clean and efficient. If used correctly this stove will burn far more efficiently than normal with the obvious notable features of CLEAN GLASS. Never clean glass when stove is hot. Always use stove glass cleaner which is available from your stove retailer.
- Page 9 Do not use liquid fuels in this appliance. Size of Fuel Log Size San Remo 4kW up to 260mm San Remo 6kW up to 300mm...
-
Page 10: Safety Notes For Your Guidance
Notes: Warning! - Petroleum coke fuels or household waste must not be burnt on this appliance. Should any difficulties arise over fuel quality or suitability, consult your local approved coal merchant. Safety Notes for your guidance FIRES CAN BE DANGEROUS – Always use a fireguard in the presence of children, the elderly or the infirm. -
Page 11: Frequently Asked Questions
Each stove will have spin valves, which will allow you to easily regulate the heat output. 5 What warranty policy do I get? San Remo Stoves will replace, free of charge, any working part that fails (under normal operating conditions) within 12 months of purchase. Consumables such as glass or stove rope are not guaranteed. - Page 12 San Remo Stoves, 30-60 Hawthorn Road, Western Industrial Estate, Naas Road, Dublin 12. T: 01 408 9192 F: 01 408 9193 HD01 18/12/11...
Need help?
Do you have a question about the 4kW and is the answer not in the manual?
Questions and answers