Table of Contents
Advertisement
•
Remote controller cable length: r
11.4. Wiring of main power supply and equipment capacity
Schematic Drawing of Wiring (Example)
[Fig. 11.4.1] (P.9)
A Switch (Breakers for wiring and current leakage)
D Pull box
Thickness of wire for main power supply, capacities of the switch and system impedance
Model
PUHY-RP200YJM-B
PUHY-RP250YJM-B
Outdoor unit
PUHY-RP300YJM-B
PUHY-RP350YJM-B
Total operating
F0 = 20A or less *2
F0 = 30A or less *2
current of the
indoor unit
F0 = 40A or less *2
*1: Meets technical requirements of IEC61000-3-3
*2: Please take the larger of F1 or F2 as the value for F0.
F1 = Total operating maximum current of the indoor units x 1.2
V1 x Quantity
V1 x Quantity
F2 =
+
of Type A
of Type B
*3: Current sensitivity is calculated using the following formula.
V2 x Quantity
V2 x Quantity
G1 =
+
of Type 1
of Type 2
G1
Current sensitivity
30mA or less
30mA 0.1sec or less
100mA or less
100mA 0.1sec or less
1. Use dedicated power supplies for the outdoor unit and indoor unit. Ensure OC and OS are wired individually.
2. Bear in mind ambient conditions (ambient temperature,direct sunlight, rain water,etc.) when proceeding with the wiring and connections.
3. The wire size is the minimum value for metal conduit wiring. If the voltage drops, use a wire that is one rank thicker in diameter.
Make sure the power-supply voltage does not drop more than 10%.
4. Specific wiring requirements should adhere to the wiring regulations of the region.
5. Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord (design 245 IEC57). For example,
use wiring such as YZW.
6. A switch with at least 3 mm contact separation in each pole shall be provided by the Air Conditioner installer.
Warning:
•
Be sure to use specified wires for connections and ensure no external force is imparted to terminal connections. If connections are not fixed firmly, heating
or fire may result.
•
Be sure to use the appropriate type of overcurrent protection switch. Note that generated overcurrent may include some amount of direct current.
Caution:
•
Some installation sites may require attachment of an earth leakage breaker for the inverter. If no earth leakage breaker is installed, there is a danger of
electric shock.
•
Do not use anything other than a breaker and fuse with the correct capacity. Using a fuse or wire of too large capacity may cause malfunction or fire.
Note:
•
This device is intended for the connection to a power supply system with a maximum permissible system impedance shown in the above table at the
interface point (power service box) of the user's supply.
•
The user must ensure that this device is connected only to a power supply system which fulfils the requirement above.
If necessary, the user can ask the public power supply company for the system impedance at the interface point.
•
This equipment complies with IEC 61000-3-12 provided that the short-circuit power S
user's supply and the public system. It is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network
operator if necessary, that the equipment is connected only to a supply with a short-circuit power S
S
(*2)
SC
(MVA)
Model
S
SC
PUHY-RP200YJM
1.25
PUHY-RP250YJM
1.54
PUHY-RP300YJM
1.75
PUHY-RP350YJM
2.31
20
, r
10 m (0.3 to 1.25 mm
2
)
=
1
2
If the length exceeds 10 m, use 1.25 mm
length and the longest remote length.
B Breakers for current leakage
E Indoor unit
Minimum wire thickness (mm
2
)
Main cable
Branch
Ground
4
-
4
4
-
4
4
-
4
6
-
6
1.5
1.5
1.5
2.5
2.5
2.5
4.0
4.0
4.0
V1 x Quantity
+
of Others
V2 x Quantity
+
of Others
PLFY-VBM, PMFY-VBM, PEFY-VMS, PCFY-VKM,
Type 1
PKFY-VHM, PKFY-VKM, PFFY-VKM, PFFY-VLRMM
Type 2
PEFY-VMA
Others
Other indoor unit
2
shielded cable and calculate the length of that portion (L
Breaker for current leakage
Capacity
30A 100mA 0.1sec or less
30A 100mA 0.1sec or less
30A 100mA 0.1sec or less
40A 100mA 0.1sec or less
20A current sensitivity *3
30A current sensitivity *3
40A current sensitivity *3
PLFY-VBM, PMFY-VBM, PEFY-VMS, PCFY-VKM,
Type A
PKFY-VHM, PKFY-VKM, PFFY-VKM, PFFY-VLRMM
Type B
PEFY-VMA
Others
Other indoor unit
V3 x Wire length [km]
+
Indoor unit
is greater than or equal to S
SC
SC
and L
) as within the total extended
4
7
C Outdoor unit
Local swtich (A)
Breaker for
Fuse
wiring (A) NFB
25
25
30
25
25
30
32
32
30
40
40
40
20
20
20
30
30
30
40
40
40
Indoor unit
Wire thickness
V2
1.5 mm
2.4
2.5 mm
1.6
4.0 mm
0
(*2) at the interface point between the
SC
greater than or equal to S
(*2).
SC
Max. Permissive
System impedance
*1
*1
*1
0.26Ω
(apply to IEC61000-3-3)
(apply to IEC61000-3-3)
(apply to IEC61000-3-3)
V1
1.6
3.2
0
V3
2
48
2
56
2
66
Advertisement
Table of Contents
