Grounding Instructions; Extension Cords - PowerTec TS1001 Owner's Manual

9. Tighten the two front and four rear adjustment nuts.
Reach under the front and rear of table with a wrench
to access these nuts. Re-check the alignment. If ad
ditional adjustments are necessary, loosen only the
front two adjustment nuts, and repeat the above steps
until the blade is parallel to the mitre gauge slot.
10. Tighten two front adjustment nuts, then stand the saw
on its left side, and tighten the four rear adjustment
nuts. Place the saw upright and re-check the alignment
to make sure the blade is parallel to the mitre gauge slot.
Figure 15

GROUNDING INSTRUCTIONS

WARNING
Improper connection of equipment grounding conductor
can result in the risk of electrical shock. Equipment should
be grounded while in use to protect operator from electri-
cal shock.
• Check with a qualified electrician if you do not
understand grounding instructions or if you are in
doubt as to whether the tool is properly grounded.
• This tool is equipped with an approved cord rated at
150V and a 3-prong grounding type plug (see Figure
14) for your protection against shock hazards.
• Grounding plug should be plugged directly into a
properly installed and grounded 3-prong grounding type
receptacle, as shown (see Figure 16).
Figure 16 3-Prong Receptacle
• Do not remove or alter grounding prong in any manner.
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electrical shock.
Ruler
Gauge Slot
Combination Square
Ruler
WARNING
Do not permit fingers to touch the terminals of plug when
installing or removing from outlet.
• Plug must be plugged into matching outlet that is
properly installed and grounded in accordance with all
local codes and ordinances. Do not modify plug
provided. If it will not fit in outlet, have proper outlet
installed by a qualified electrician.
• Inspect tool cords periodically, and if damaged, have
repaired by an authorized service facility.
• Green (or green and yellow) conductor in cord is the
grounding wire. If repair or replacement of the electric
cord or plug is necessary, do not connect the green (or
green and yellow) wire to a live terminal.
• A 2-prong wall receptacle must be replaced with a
properly grounded 3-prong receptacle installed in
accordance with National Electric Code and local codes
and ordinances.

EXTENSION CORDS

• The use of any extension cord will cause some drop in
voltage and loss of power.
• Wires of the extension cord must be of sufficient size to
carry the current and maintain adequate voltage.
• The minimum extension cord wire size is A.W.G. 14.
Do not use extension cords over 25 feet long.
• Use only 3-wire extension cords having 3-prong
grounding type plugs and 3-pole receptacles which
accept the tool plug.
• If the extension cord is worn, cut or damaged in any
way, replace it immediately.
MOTOR
Table Saw is supplied with a 2-1/2 HP motor installed.
The 120 Volt AC universal motor has the following
specifications:
Horsepower (Peak HP) . . . . . . . . . . . . . . . . . . . . .2-1/2 HP
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Amperes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Hertz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,000