ELICA EPR628SS Installation Instruction Manual
  1. Manuals
  2. Brands
  3. ELICA Manuals
  4. Ventilation Hood
  5. EPR628SS
  6. Installation instruction manual
ELICA EPR628SS Installation Instruction Manual

ELICA EPR628SS Installation Instruction Manual

Elica epr628ss; eas428ss range hoods
Hide thumbs Also See for EPR628SS:
Table of Contents

Advertisement

Quick Links

Installation Instructions Guide

READ AND SAVE THESE INSTRUCTIONS

English
page
Français
page
Spanish
page
Instructions d'installation Guide
Guía de Instrucciones para Instalación
INSTRUCTIONS D'INSTALLATION GUIDE
LEA Y GUARDE ESTAS INSTRUCCIONES
3
14
Model: EPR628SS
Model: EAS428SS
LI31MA Ed. 05 / 13

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EPR628SS and is the answer not in the manual?

Questions and answers

Related Manuals for ELICA EPR628SS

Summary of Contents for ELICA EPR628SS

  • Page 1: Read And Save These Instructions

    Installation Instructions Guide Instructions d’installation Guide Guía de Instrucciones para Instalación Model: EPR628SS Model: EAS428SS READ AND SAVE THESE INSTRUCTIONS INSTRUCTIONS D’INSTALLATION GUIDE LEA Y GUARDE ESTAS INSTRUCCIONES English page Français page Spanish page LI31MA Ed. 05 / 13...

  • Page 3: Table Of Contents

    Table of Contents APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY Important Safety Notice ............3 READ AND SAVE THESE INSTRUCTIONS Tools and parts ................ 4 Location Requirements ............4 PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. Product Dimensions ............4 INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

  • Page 4: Tools And Parts

    • 6 - 3.5 x 9.5 mm sheet metal screws • T10 TORX®† adapter Parts needed I* - Metallic spacers ■ 6” (15.2 cm) round metal vent system Spacers has to be installed and used when cabinet depth is greater than 12”. EAS428SS / EPR628SS range hood models Dimension DIM A ⁄ ” (71.8 cm) DIM B 26” (66 cm) DIM C 1 ⅛” (2.9 cm)

  • Page 5: Venting Requirements

    Installation Clearances VENTING REQUIREMENTS ■ Vent system must terminate to the outdoors, except for no vented (recirculating) installations. ■ Do not terminate the vent system in an attic or other enclosed area. ■ Do not use a 4” (10.2 cm) laundry-type wall cap. ■ Use metal vent only. A rigid metal vent is recommended. Plastic or metal foil vent is not recommended.

  • Page 6: Venting Methods

    Venting Methods Vent Piece 6” (15.2 cm) 45° elbow 2.5 ft This range hood is factory set for venting through the roof or (0.8 m) through the wall. You can apply the recirculating venting method by purchasing the Recirculation Kit. The vent system needed for installation is not included. A 6” (15.2 cm) round vent system is recommended.

  • Page 7: Installation Instructions

    ■ The grounded 3 prong outlet is to be located inside the GROUNDING INSTRUCTIONS cabinet above the range hood at a maximum distance of ■ For a grounded, cord-connected range hood: ⁄ ” (85.0 cm) from where the power cord exits the hood. The grounded 3 prong outlet must be accessible after This range hood must be grounded.
  • Page 8 Venting Outside Through the Roof Non-Vented (recirculating) Installation Through the Measure and mark the lines as shown. Use a saber saw or Soffit/Cabinet keyhole saw to cut an opening through the top of the cabinet and the roof for the vent. Go to Step 3. A.

  • Page 9: Install Range Hood

    Install Range Hood Complete Preparation 3. If not yet attached, install the 6” (15.2 cm) vent transition the top of the range hood liner using two 3.5 x 9.5 mm screws. 4. Locate side mounting bracket flush 1 cm to the bottom of the cabinet side and against the inside of the front cabinet face. WARNING Orient the bracket depending on the width of your cabinet as depicted in the diagrams below. Drill ⅛” (3 mm) pilot holes in Excessive Weight Hazard 6 places, attach a bracket using three 4.5 x 13 mm screws to...

  • Page 10: Connect The Vent System

    Complete Installation 1. Replace grease filters. See the “Range Hood Care” section. WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. A. Screws - 3.5 x 9.5 mm flat-head (4) B. Face plate (30” x 12” [76.2 cm x 30.5 cm] shown) Do not use an adapter. C. Cabinet (30” x 12” [76.2 cm x 30.5 cm] shown) D. Screws - 4.2 x 15 mm truss-head (2) Do not use an extension cord. Failure to follow these instructions can result in For cabinet size - 30”...

  • Page 11: Range Hood Use

    A. Blower and light controls B. Grease filter C. Grease filter handle D. Halogen or Incandescent lamps (depending of hood model) Range Hood Controls A. EPR628SS model spring release handle A. On/Off light button B. Blower off and speed minimum button C. Blower speed medium button D. Blower speed maximum button Operating the Light The On/Off light button controls all lights.

  • Page 12: Available Accessories

    EPR628SS which provides complete protection of cabinets (model number EXXHDL30). • 36” wide x 17” or 20” deep liner is available for both EAS428SS and EPR628SS which provides complete protection of the cabinets (model number EXXHDL36). See Liner installation instructions for more detail. Reconnect power.

  • Page 13: Warranty

    Products. WHO TO CONTACT To obtain Service under Warranty or for any Service Related Question Please Call: • Elica North America Authorized Service at (888) 732-8018 Or by Writing To: • Elica North America, Attention Customer Service, 6658 156th Avenue SE, Bellevue, WA 98006 USA infoamericas@elica.com...

This manual is also suitable for:

Eas428ss

Table of Contents