SMK-Link VP3720 User Manual

SMK-Link VP3720 User Manual

Universal projector remote control
Hide thumbs Also See for VP3720:

Advertisement

SMK-Link
Electronics
Universal Projector
Remote Control
Cover
VP3720
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VP3720 and is the answer not in the manual?

Questions and answers

Summary of Contents for SMK-Link VP3720

  • Page 1 SMK-Link Electronics ™ Universal Projector Remote Control Cover VP3720 Page 1...
  • Page 2: Table Of Contents

    Table of Contents Regulatory Information ..............1 Getting Started ................3 Setting your Projector ..............4 Entering Library Codes ..............4 Learning From Another Remote ...........5 Searching For A Code ..............6 Show Current Code ..............7 Factory Reset ................8 Remote Control Layout ..............9 Appendix: Library Codes List ............11...
  • Page 3: Regulatory Information

    Regulatory Information Regulatory Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Certification This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
  • Page 4: Declaration Of Conformity

    Industry Canada technical specifications were met. Declaration of conformity Hereby, SMK-Link Electronics Corporation declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. All trademarks and registered trademarks mentioned in this document are the property of their respective owners.
  • Page 5: Getting Started

    Getting Started The Universal Projector Remote control uses two AA batteries. • Remove the battery cover by pressing down on the battery door and sliding in the direction of the arrow. • Remove any wrapping from two AA batteries and insert them into the back of the remote control.
  • Page 6: Setting Your Projector

    Setting your Projector Entering Library Codes To test a four-digit code to see if it controls your projector, please complete the following steps. Available codes are listed in the Appendix. Some brands have multiple codes which work for different models. •...
  • Page 7: Learning From Another Remote

    Learning From Another Remote If you have access to the original remote control for your projector or wish to learn from other remote controls, place the two remote controls end pointing towards one another approximately two to three inches apart. •...
  • Page 8: Searching For A Code

    – On the other remote control, press and hold the key you wish the Universal Projector Remote to learn. – If learning was successful, the status LED will flash once. If learning was unsuccessful, the status LED will flash three times.
  • Page 9: Show Current Code

    • Press the Zoom + key to search through codes from the beginning of the Library in ascending order. • Press the Zoom - key to search through codes from Zoom the beginning of the Library in descending order. • Every time the Zoom + or Zoom - key is pressed, the IR code corresponding to the Menu key will be transmitted for one second.
  • Page 10: Factory Reset

    • Press Select, wait one second then press Select a second time. The LED will then flash the code digit by digit with a one second delay between each digit. The library code 1 2 1 3 would blink the status LED.
  • Page 11: Remote Control Layout

    Remote Control Layout Note: Not all brands support all keys. Unused keys may be ignored or customized through learning. Power: Turn the projector on. Some brands use this key for both power on and power off. Off: Some brands of projectors have a dedicated key to turn the projector off.
  • Page 12 Hide: Turns the screen black. Aspect: Switch between 4:3 and 16:9 modes. Status Power Volume +, Volume -: Turn the projector volume up or down. Mute: Turn the projector’s sound to the Input Input lowest setting. Back Freeze: Freezes the image on the screen. Reset: Send reset or exit command to Select projector, also used to exit setup.
  • Page 13: Appendix: Library Codes List

    Appendix: Library Codes List Brand 1122 1411 1413 2341 3324 3414 3421 1144 ACER 1231 4344 1213 1232 BENQ 1132 4411 BOXLIGHT 1122 1211 1224 1333 1411 2123 2124 2324 2424 2431 CANON 1133 CASIO 1121 COMPAQ 1334 DELL 1134 4232 4233 DUKANE...
  • Page 14 HITACHI 1122 1234 1411 1412 1413 2133 2134 2141 2231 2232 2233 2333 2334 2341 2432 2433 2434 3134 3141 3142 3143 3241 3242 3323 3324 3331 3414 3421 3422 3441 3442 4114 4121 4122 4123 1141 INFOCUS 1121 1213 1313 1142 1241...
  • Page 15 SAMSUNG 1131 2112 2314 3223 3224 4144 4211 SANWA 3221 SANYO 1214 1224 1244 1322 1421 1422 1423 2122 2123 2124 2142 2143 2242 2324 2424 2431 3144 3211 3423 3424 4241 4242 4243 SHARP 1123 1311 1323 1443 1444 2111 2213 2214...
  • Page 16 Page 14...

Table of Contents