Related Manuals for Eskimo Mako M43
Summary of Contents for Eskimo Mako M43
- Page 1 Power Ice Auger Operator's Manual Models Models M43, M43T8, M43Q8 M43Q9, M43Q10 S33Q8 IB-S33/M43 Rev. 08/31/04 © Copyright 2004 Ardisam, Inc. All Rights Reserved. Printed in USA.
- Page 2 Page 2...
-
Page 3: One Year Limited Warranty
Place of Purchase ______________________________ ARRANTY One Year Limited Warranty The Ardisam, Inc., Manufacturing Company warrants this Eskimo® Ice Auger to be free from defects in material or workmanship. Conditions of this warranty include: What is covered under warranty: Ardisam, Inc. will repair or replace any part defective in workmanship or material within one year after delivery of the ice auger to the original purchaser. -
Page 4: Owner's Responsibility
• Carefully follow all assembly instructions. with the controls. • Maintain the auger according to directions and schedule included in this Eskimo operator’s manual. • Ensure that anyone who uses the auger is familiar with all controls and safety precautions. -
Page 5: Engine Safety Precautions
AFETY Engine Safety Precautions Gasoline Fires or Handling Fuel Safely Fuel and fuel vapors are highly flammable. Never use fuel Warning Carbon Monoxide Poisoning where a spark or flame may be present. Never use fuel All engines contain carbon monoxide in their exhaust. where a potential source of ignition could occur. -
Page 6: Gas And Oil
AFETY Burns and Fires CAUTION The muffler, muffler guard and other parts of the engine Avoid injury! Always wear hearing protection while become extremely hot during the operation of the engine. operating engine. These parts remain extremely hot after the engine has stopped. -
Page 7: Mixing Fuel/Filling Fuel Tank
OPERATION Mixing Fuel and Filling Fuel Tank Filling Fuel Tank 1. Shut-off engine and allow engine to completely cool before refilling the fuel tank. CAUTION 2. Move to a well ventilated area, outdoors, away from flames and sparks. Avoid injury! Never store engine with fuel in the tank indoors. -
Page 8: Starting And Stopping Engine
OPERATION Starting and Stopping Engine 7. Grasp starter handle and pull out slowly, until it pulls slightly harder. Without letting it retract, pull rope with a rapid To attach auger to powerhead if not done, align hole in at full arm stroke. Let it return to its original position very top of shaft with output shaft hole. -
Page 9: Normal Operation
OPERATION Normal Operation Transporting Your Ice Auger 1. The clutch will transfer maximum power after about two 1. Never transport engine inside an enclosed space or hours of normal operation. During this break-in period clutch vehicle. Fuel or fuel vapors may ignite causing serious slippage may occur. -
Page 10: Auger Maintenance
MAINTENANCE AND TORAGE Cooling Fins CAUTION • Cooling fins, air inlets and linkages must be free from any debris before each use. To prevent accidental starting: Avoid injury! Engine must be turned off and cool, and Air Filters spark plug wire must be removed from spark plug •... - Page 11 MAINTENANCE AND TORAGE Long Term Storage • If your ice auger will not be ran for more than one month, prepare it for long term storage. Steps for Long Term Storage 1. Add fuel stabilizer according to manufacturer’s instructions. 2. Run engine for 10-15 minutes to ensure that the stabilizer reaches the carburetor.
-
Page 12: Service Information
ERVICE, TROUBLE HOOTING AND REPAIR ICE POINT REPLACEMENT SERVICE INFORMATION 1. Remove blade protector and both blades. 2. Remove nut and retaining bolt from point. 3. Using a locking pliers, grasp point and pull out. If holder IN CASE OF A SERVICE PROBLEM, DO NOT SEND doesn’t come out with the point, remove with pliers. -
Page 13: Troubleshooting
ERVICE, TROUBLE HOOTING AND REPAIR ORDERING REPAIR PARTS Please include the following information with your order: 1. Part numbers Parts can be obtained from the store where your auger was purchased or direct from the factory. To order from the 2. -
Page 14: 33 Tingray & M43 Mako Engine Parts List
33 TINGRAY & M43 MAKO ENGINE PART LI T Page 14... - Page 15 33 TINGRAY & M43 MAKO ENGINE PART LI T MINIMUM ORDER ................$10.00 POWERHEAD PARTS Part # Description Qty. Part # Description Qty. 1021 Rocker Switch 300462 Rotor Washer 300401 Fuel Tank Cap 300463 Grommet, Engine Shroud 300412 Clutch Spring 300464 Cover, Engine Shroud, S33 300428...
- Page 16 33Q8 TINGRAY PART LI T Page 16...
- Page 17 Spacer-Drum 300414 Clutch Drum 300419 Gear, 7T 300421 Gear, 48T left hand thread 300425 Gas Engine, 33cc LBL33 Decal, StingRay, serialized LBL332 Decal, StingRay oval, handlebar plate LBLBPE Decal, Blade Protector, Eskimo LBLESKS Decal, Eskimo oval, auger stem Page 17...
- Page 18 M43 MAKO PART LI T Page 18...
- Page 19 Decal, Mako oval, handlebar plate QT9N Ice Auger, 9" Quantum, complete LBLBPE Decal, Blade Protector, Eskimo QT10N Ice Auger, 10" Quantum, complete LBLESKS Decal, Eskimo oval, auger stem ACCESSORIES EXT6 Depth Extension, 6" EXT12 Depth Extension, 12" EXT18 Depth Extension, 18"...
- Page 20 Ardisam, Inc. 1690 Elm Street, Cumberland, Wisconsin 54829 Phone (715)822-2415 • Fax (715)822-4180 1-800-345-6007 Email info@ardisam.com www.ardisam.com...
Need help?
Do you have a question about the Mako M43 and is the answer not in the manual?
Questions and answers