Do you have a question about the Olympus M200 and is the answer not in the manual?
Questions and answers
LEANDRO GUATY ROCA
June 20, 2025
HOW DO I REGULATE THE SELF-EMPTYING SYSTEM? THE TANK FILLS WITH DIRTY WATER AND OVERFLOWS. WHEN I MOVE THE FLOAT, THE SELF-EMPTYING PUMP WORKS. THE PROBELAMD MUST BE IN SOME REGULATION ON THE FLOAT.
Page 10
• ; • 1 • - Proportioning Valve Turquoise Tip Dilution 256 - 1 Red Tip Dilution 85 - 1 Metering Tip Kit – PDE001 A B 2 ! 3 " 22*2 + 5*2 ; • 2 2F ,.*2 • •...
Page 11
• • 23 ° • J(6 2 K (6 ? Chemical Feed Hose Connect the Auto-Fill Water Supply Hose to a faucet and turn on the water Connect the Auto-Fill Water Supply Hose to Solution Inlet (Male quick connect on the front of the machine.) 3/8”...
Page 12
#< $ 2 $ 3 • • 9 • % • 9 • • • • % • % Pump Prime Hose NM5080 Place end of prime hose and use Keep prime hose connected and run vacuum to prime the solution pump. pump until flow is strong and steady...
Page 13
&< " Connect the male end of the HP Solution Hose Assembly to the female solution outlet fitting on HP Solution Hose Assembly – AH79D the machine. Connect the female end to the 1/4” id X 25’ with M-F Quick Connects cleaning tool.
& Troubleshooting – Olympus M200 Problem Cause Solution Machine not Building circuit breaker tripped. Reset breaker or move cord to other outlet turning on - Faulty power cord Replace cord (AX32) No power Faulty switches or internal wiring Check wiring & test switches - Repair as needed *...
Page 18
Problem Cause Solution Pump-out Building circuit breaker tripped. Reset breaker or move cord to other outlet not working Faulty power cord Replace cord (AX32) Check wiring & test switches - Repair as needed * Faulty switches or internal wiring (NM5008) Optional Pump-out pump faulty Replace pump-out pump (NM5053)
Page 19
Problem Cause Solution Solution Tank Water source turned off Turn on faucet or find other water source not filling Float not on valve arm Reconnect float to valve arm - Adjust to proper height/level Float valve faulty Repair or replace float valve (NM5055) Optional Water hose restricted Un-kink, clean out or replace hose...
Page 27
2 L79 3 9* B " " $ 2 ! 3 !" % " • 8 • ; • ; • A# • ; • I * ( 22( ( 22I N =7 ( 229 70 A; I(: N ( 22( 079 N ( 229 ;7G: 70 A;...
Page 28
B . $ • ( & • % • 1 • 0 • 1 • • • 8 • % • 9 • • 0 ! < Pour 2 or 3 gallons of clean : < water into Solution Tank •...
Page 29
* B " Direct the end of the prime hose into the recovery tank vacuum barb Vacuum acid solution out of Solution Tank • ; Solution Tank 8 A /...
Page 30
G 2 2 B . $ • ; Place Chemical Feed Hose into • ; Rinse Solution • • • • 8 • % • 8 • Connect Auto-Fill Water Supply Hose to machine and faucet Vacuum water out of Solution Drain water from Recovery Tank Tank...
Page 31
1 9L A 79 " ? : 6 % ? " $ ! ? ? < • 1 • - FLANGE FITTING Unless damaged or leaking between Remove four bolts holding valve tank and flange, the flange fitting does assembly to flange fitting not have to be removed VALVE BODY OUTLET...
Need help?
Do you have a question about the Olympus M200 and is the answer not in the manual?
Questions and answers
HOW DO I REGULATE THE SELF-EMPTYING SYSTEM? THE TANK FILLS WITH DIRTY WATER AND OVERFLOWS. WHEN I MOVE THE FLOAT, THE SELF-EMPTYING PUMP WORKS. THE PROBELAMD MUST BE IN SOME REGULATION ON THE FLOAT.