forest river Travel Trailer Owner's Manual page 52

• Shut off the fresh water pump or disconnect from
your city water supply. Open the kitchen faucets to
remove pressure. Place a shallow pan beneath The
WaterPur™ housing by turning counter-clockwise,
being careful not to spill the water in the housing.
Empty the water from the housing.
• Unwrap the WaterPur™ cartridge and place it in the
housing (either side up). Make certain that the 'O'
Ring is properly seated, and reattach the housing to
the filter cap by turning clockwise. Tighten the hous-
ing firmly by hand. DO NOT over-tighten.
• Close the kitchen faucets and either turn on your
fresh water pump or your city water supply. Check
for leaks at the filter housing. Tighten if necessary.
Open the kitchen faucet and allow water to flow for
ten minutes. Your WaterPur™ system is now ready
to deliver fresh-tasting, filtered water to all of the
faucets in your RV.
To winterize your RV's water system, remove The
WaterPur™ cartridge from the housing and follow manu-
facturer's directions for de-winterizing, then replace The
WaterPur™ cartridge. The cartridge should be replaced
every 12 months or 10,000 gallons, whichever comes
first.
An easy way to remember to do this is to replace the
cartridge when you de-winterize in the spring. Replace
The WaterPur™ cartridge only with a genuine
WaterPur™ cartridge available from your Forest River
Inc. dealer.
Operational Note: The WaterPur™ cartridge is not to be
autoclaved or steam sterilized. Use the WaterPur™ car-
tridge with microbiologically safe water. Activated carbon
filters are not designed to kill or remove bacteria or
viruses. Actual results obtained will vary with various
combinations of organic contaminants, changes in pH or
other conditions encountered in actual use. All informa-
tion presented is based on data believed to be reliable. It
is offered for evaluation and verification, but is not to be
considered a warranty of any kind. The contaminants
removed by The WaterPur™ cartridge are not necessar-
ily in your water. Some jurisdictions tax, regulate, or
restrict devices making health related or aesthetic
claims. WaterPur™ makes no claims in those
jurisdictions.
CARE AND MAINTENANCE
Warranty
The WaterPur™ system is warranted against defects in
material and workmanship for a period of one year from
date of purchase. Warranty does not cover damage due
to abuse, neglect, improper installation, exposure to
pressure or temperature above or below stated operating
parameters, or improper winterizing.
The Seller makes no other warranties of any kind,
expressed or implied, concerning this product, including
warranties of merchantability or fitness for a particular
purpose except that this product should be capable of
performing as described in this manual.
Seller's obligation for this product's performance below
specifications shall be limited solely to the replacement
of product proven defective, at the Seller's sole discre-
tion. Determination of suitability of product of uses con-
templated by Buyer shall be the sole responsibility of
Buyer. Use of this product constitutes Buyer's accep-
tance of this limited liability.
Description:
The WaterPur™ model CCi-10CLW12 is a Household
Class, Group 2, water filtration device designed for
installation in recreational vehicles. It has a micron rating
of 1 micron, a capacity of 10,000 gallons of chlorine
removal at 2.5 gallons per minute. This capacity was
determined under WQA Standard S-200 Test Conditions
and may vary with local water characteristics.
The cartridge consists of activated carbon particles fused
into a uniform block with enhanced absorptive capacity
and efficiency. The cartridge flows in a radial outside-to
inside direction providing increased dirt capacity and low
pressure drop (8 psid @ 1 gpm service flow, maximum
differential pressure of 100 psid and a collapse pressure
of 200 psid).
Unlike granular activated carbon (GAC) filters, the
extruded carbon will not channel or bypass due to the
extreme uniformity of its extruded activated carbon core.
Service life is greatly extended by a layer of 15 micron
polypropylene spun-bonded prefiltration medium and a
second layer of 5 micron polypropylene melt blown filter
medium.
Maximum cartridge operating pressure is 125 psid and
maximum operating temperature is 1250° F. Minimum
operating temperature is 400° F. The housing and car-
tridge are constructed of 100% NSF listed materials.
51