Related Manuals for Jasco ZW3103
Summary of Contents for Jasco ZW3103
- Page 1 Wireless Lighting Control On/Off/Dim Lamp Module 45702 Z-Wave Certified ZW3103 ® Wireless Lighting Control Made in China...
- Page 2 Introduction: Thank you for your purchase of a Jasco Z-Wave control ® device. Z-Wave technology is designed to automate ® lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The Jasco Z-Wave ® ® product family includes a variety of devices to control lighting in your home.
- Page 3 The lighting load plugged into the Z-Wave controlled ® outlet on this module must not exceed 300 watts incandescent. This module has been optimized for use with incandescent lighting as well as with most dimmable CFL and LED bulbs. NOTE: Actual performance of any CFL or LED will vary from bulb type to bulb type and among different manufacturers.
- Page 4 For these reasons, we recommend the following: 1. Assign Z-Wave controlled appliances to device numbers 10 – 18 on the Jasco remote. The likelihood of unintentionally turning on the appliance will be reduced significantly because the “Shift” button will need to be pressed before pressing device numbers 10-18.
- Page 5 Z-Wave enabled devices installed in the control network. Jasco Z-Wave Network Every Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-spots”.
- Page 6 Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices. Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to destination device: Type of Construction Wood Frame Brick, Tile or w/Drywall...
- Page 7 Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A”...
- Page 8 Remote Control Jasco Z-Wave remotes provide control of an Individual device, Groups of devices and Scenes. Other brands of Z-Wave Certified remotes may not offer as much flexibility in how you can set up your lighting control network.
- Page 9 2. Adjust the brightness level of the connected lighting by pressing and holding the button. Release the button when the desired level is attained. - This is also a toggle function. The lighting will dim until the minimum level is attained or the button is released. The next time the button is pressed and held, the level will increase until the maximum level is attained or the button is released.
- Page 10 All On/All Off Depending upon your primary controller, the 45702 lamp module can be set to respond to ALL ON and ALL OFF commands in up to four different ways. Some controllers may not be able to change the response from its default setting.
- Page 11 Dim Rate Adjustments Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”.
- Page 12 Restoring Factory Defaults All Configuration Parameters can all be restored to their factory default settings by using your primary controller to reset the device. (delete from the network) Software Fuse This Lamp Module is designed to protect itself against loads that exceed its maximum power rating.
- Page 13 Advanced Remote with LCD readout can control other Z- Wave certified devices like thermostats as well as lighting. WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited...
- Page 14 U2Z45602-3 The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 15 RF exposure requirements and void user’s authority to operate the device. Compliance with IC Rules and Regulations IC: 6924A-45602A3 Jasco Products Company Model: ZDP100 / 45702 / ZW3103 CAN ICES-3(B) / NMB-3(B) SPECIFICATIONS Power 120VAC, 60Hz Signal (Frequency) 908.42 MHz Maximum load for both outlets 15A, 1800W Resistive Maximum load for the Z-Wave controlled outlet: 2.5A 300 W...
- Page 16 Distributed by Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, Oklahoma 73114. Made in China Hecho en China All brand names shown are trademarks of their respective owners. Todas las marcas que aparecen aquí son marcas registradas de sus respectivos dueños.