Disassembly/Assembly Procedures Of Deck Mechanism - Hitachi DV-PF3A(S) Service Manual

4-2 DISASSEMBLY/ASSEMBLY PROCEDURES OF DECK
MECHANISM
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to
CABINET DISASSEMBLY INSTRUCTIONS on page 4-1.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject
mode; see the positions of [44] and [45] in Fig. 4-2-1 on page 4-8. When reassembling, follow the steps in reverse
order.
STEP START-
/LOC. ING
No. No.
[1] [1] Guide Holder A
[2] [1] Cassette Holder Assembly T
[3] [2] Slider (SP)
[4] [2] Slider (TU)
[5] [4] Lock Lever
[6] [2] Cassette Plate
[7] [7] Cylinder Assembly
[8] [8] Loading Motor Assembly
[9] [9] AC Head Assembly
[10] [2] Tape Guide Arm Assembly T
[11] [10] C Door Opener
[12] [11] Pinch Arm (B)
[13] [12] Pinch Arm Assembly
[14] [14] FE Head Assembly
[15] [15] Prism
[16] [2] Slider Shaft
[17] [16] C Drive Lever (SP)
[18] [16] C Drive Lever (TU)
[19] [19] Capstan Motor
[20] Clutch Assembly (HI)
[20]
[21] [20] Center Gear
[22] [22] F Brake Assembly (HI)
[23] [22] Worm Holder
[24] [22] Pulley Assembly (HI)
[25] Mode Gear
[25]
[26] Mode Lever (HI)
[20],[25]
[22],[23],
[27] Cam Gear (A) (HI)
[26]
[28] [26] TR Gear C
[29] [28] TR Gear Spring
[30] [29] TR Gear A/B
[31] [31] FF Arm (HI)
Idler Assembly (HI)
[32] [26]
[33] [26] BT Arm
4-6
PART
Fig. No.
T 4-2-3
4-2-4
T 4-2-5
T 4-2-5
T 4-2-5
T 4-2-5
T 4-2-1,4-2-6
T 4-2-1,4-2-7
T 4-2-1,4-2-7
4-2-1,4-2-8
T 4-2-1,4-2-8
T 4-2-1,4-2-8
T 4-2-1,4-2-8
T 4-2-1,4-2-9
T 4-2-1,4-2-9
T 4-2-10
T 4-2-10
T 4-2-10
B 4-2-2,4-2-11
B 4-2-2,4-2-12
B 4-2-12
B 4-2-2,4-2-12
B 4-2-2,4-2-13
B 4-2-2,4-2-13
B 4-2-2,4-2-13
B 4-2-2,4-2-13
B 4-2-2,4-2-13
B 4-2-2,4-2-13
B 4-2-13
B 4-2-13
B 4-2-1,4-2-13
B 4-2-1,4-2-14
B 4-2-2,4-2-14
REMOVAL
REMOVE/*UNHOOK/
UNLOCK/RELEASE/
UNPLUG/DESOLDER
2(S-1)
*(L-1), (S-1A)
*(L-2), (S-1B)
*(L-3),*(P-1)
Desolder, 3(S-2)
Desolder, LDG Belt,
2(S-3)
(S-4)
*(P-2)
*(L-4)
*(P-3)
(S-5)
(S-6)
*(L-5)
(S-7),*(P-4)
3(S-8), Cap Belt
(C-1)
*(L-6)
(S-9),*(L-7),*(L-8)
(C-2)
(C-3)
(C-4)
(C-5)
*(L-9)
*(P-5)
INSTALLATION
ADJUSTMENT
CONDITION
(+)Refer to Alignment
Sec.Page 4-13