Table of Contents
Advertisement
Quick Links
How to install and
operate the
X-D11
digital mono
amplifier
Welcome!
This owners manual is written in easy english and
uses a lot of drawings to simply the installation and
use of the above amplifier.
Your X-program amplifier must be installed correctly
in order to work well. This manual will show you how
to install the amplifier like a pro. Please read the
entire manual before beginning the installation.
Install the amplifier yourself if you feel confident with
our instructions and if you have the proper tools.
However if you feel unsure, turn over the installation
job to someone better suited to it.
Warranty Service
This amplifier is covered by warranty, depending on
the conditions in the country where it is sold. If the
amplifier is returned for service, please include the
original dated receipt with the product.
Technical Assistance
For technical assistance ask the shop where the
product was sold or the distributor in your very coun-
try.
You can always phone the DLS Helpdesk in Sweden
+ 46 31 84 00 60 or send an e-mail to info@dls.se.
Information can also be found on our WEB-site
www.dls.se
DLS Svenska AB
P.O. Box 13029
S-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.xprogram.com
Contents
Specifications................................
Features...................................
Installation................................
Trouble-shooting........................
Tools and materials needed..........
Amplifier installation kit................
Routing Wires............................
Power and Outputs.....................
Inputs and controls.....................
Input level control..........................
Crossovers..................................
Phase control.............................
Bass boost control.........................
Speaker wiring:
Single amplifier system.................
Testing..........................................
Bridging two amplifiers...................
Professional tips..........................
Specifications
X-PROGRAM
Number of channels
Power output in 4 ohm (0,4% THD)
Max output in 2 ohm (0,7% THD)
Max output in 1 ohm (1% THD)
All above output power ratings at 13,8 Volt
Signal to noise ratio, A-weighted
Damping factor
Frequency response
Input impedance, low level
Input impedance, high level
Input sensitivity
Phase control 0-180 degrees variable yes
Remote bass boost control
Bass boost adjustable gain @45 Hz
Filter subsonic, 24 dB slope
Filter lowpass 24 dB slope
Bridge mode (master/slave selector)
Max size for power cables
Max size for speaker cables
Power consumption, idle
Maximum current draw
Built-in fan cooling
Fuse
Dimensions (mm)
Dimensions (inch)
Weight
Approval of electromagnetic compatability according
to the EEC Directive 72/245/EEC and 2006/96/EC
E 13
Approval No: 03 6367
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
1
2
2
2
3
3
3
4
5
5
5
5
6
6
6
7
8
X-D11
1
1 x 400 W
1 x 750 W
1 x 1050 W
>100 dB
>100
15 Hz - 160 Hz
10 kohm
100 ohm
0,15 - 5V
yes
0 - +18 dB
15 - 50 Hz
15 - 150 Hz
Yes
21 mm
2
(4AWG)
2
10 mm
(7AWG)
1,5 A
120 A
yes
4 x 30A
50x430x250
2x16,93x9,84
5,3 kg (11,7 lb)
Advertisement
Table of Contents
Related Manuals for DLS X-D11
Summary of Contents for DLS X-D11
-
Page 1: Table Of Contents
Built-in fan cooling You can always phone the DLS Helpdesk in Sweden Fuse 4 x 30A + 46 31 84 00 60 or send an e-mail to info@dls.se. Dimensions (mm) 50x430x250 Information can also be found on our WEB-site Dimensions (inch) 2x16,93x9,84 www.dls.se... -
Page 2: Features
If short circuiting continues, contact your local Installation DLS dealer. A fault may exist in the amplifier. 5. To start the amplifier requires a remote voltage of 9-15 volt. Check the voltage with a multi meter. -
Page 3: Tools And Materials Needed
20 feet of AWG 15 = 1,5 mm wire for remote turn on / off cable from radio. The X-D11 is a mono amplifier with high power output. The current draw is also high so you must make sure RCA-cable for input from radio. -
Page 4: Wiring
, through fuse to prevent corrosion. Use an ANL fuse holder like the DLS FH2B with fuse value 100 A if you the built in remote wire and into the RCA cable. Thus we recommend to use a separate remote wire use the AWG4 cable. -
Page 5: Input And Controls
X-D11 Input and controls Input Level control Input Wiring Inputs may be low level from the RCA output of the The input level control, 5V – 0,15 V, car stereo or high level from the car stereo speaker matches the output of your radio to the output.Low level = RCA is to prefer for the best sound... -
Page 6: Bass Boost Control
X-D11 Bass boost control on X-D11 Remote Bass boost control Bass boost control is used to set You can fine tune your bass level the bass volume. You can select the from the front of your car. Connect Bass Level... -
Page 7: Bridging Two Amplifiers
X-D11 Bridging two amplifiers Master slave selector & Data link connection Connecting two X-D11 in bridge mode will double You can connect t two X-D11 in Bridged the output power. Minimum speaker load is then 2 mode bridge mode. ohms. The output power with a 4 ohm load is 1500 One of the amplifiers is ”Master”... -
Page 8: Professional Tips
1,5 Volt route original cable away from source of interference. If noise remains regardless of cable position, try to use so called Quasi-balanced signal cables. DLS PRO or ULTIMATE cables are quasibalanced. Professional Tip: Professional Tip: Installing in trunk Securing wires When installing the amplifier in the trunk, run the Use wire ties to bundle together when possible.