Subscribe to Our Youtube Channel
Related Manuals for Iron & Oak BHH2099
Summary of Contents for Iron & Oak BHH2099
- Page 1 I I r r o o n n & & O O a a k k 2 2 2 2 a a n n d d 3 3 0 0 T T o o n n Horizontal Log Splitter M M o o d d e e l l B B H H H H 2 2 0 0 9 9 9 9 a a n n d d B B H H H H 3 3 0 0 9 9 9 9 Owner / Operator and Safety Manual...
- Page 2 Initial Start-up Instructions Read all assembly, operating, and safety instructions. Complete and return the warranty card to register your log splitter. Write the serial number and date-of-purchase in this manual. Assemble the log splitter. Make sure the oil filter is properly installed. (See “Assembly Procedure” section.) Fill the hydraulic tank with the recommended type and quantity of oil.
-
Page 3: Table Of Contents
Contents WARNING Introduction ............4 To avoid personal injury or death, carefully read and understand all Safety. -
Page 4: Introduction
With 22 or 30 tons of splitting force, a 12 second cycle time, and a 5 or 8 the work area. HP engine, the BHH2099 or BHH3099 will handle most of your commercial log splitting needs. An attractive powder-coated finish provides the finest protection available, and NEVER operate your log splitter on slippery, wet, muddy, or icy surfaces. -
Page 5: Log Splitting Safety
Do not, under any circumstances, alter your log splitter. This equipment was ALWAYS check the oil level in the hydraulic oil tank and engine reservoir. designed and engineered to be used in accordance with the operating instruc- tions. Altering the equipment, or using the equipment in such a way as to cir- NEVER operate your log splitter when it is in need of repair or is in poor cumvent its design capabilities and capacities, could result in serious or fatal mechanical condition. -
Page 6: Refueling
The following chart contains the list of parts that should be shipped as part of the Always store gasoline in an approved, tightly sealed container. Store the con- BHH2099 or BHH3099 Log Splitter. tainer in a cool, dry place. Do not store the container in a house or near any... -
Page 7: Unpacking The Crate
Unpacking the Crate Assembly Procedure 1. Cut the metal banding and remove the top, CAUTION sides, ends, and protective plastic cover- Some components are very heavy ing of the packing crate. Do not remove and can be damaged if mis-handled. the base unit or the rail assembly from the Also, to help prevent personal injury, bottom pallet at this time. - Page 8 4. Position wooden blocking under the 7. Bolt the base unit to the rail assembly engine mounting plate to level and support using four 1/2-13 x 1-1/2 inch long hex the base unit. head bolts, lockwashers, and nuts, as shown. Tighten the nuts securely. 5.
- Page 9 11. Install the valve link onto the valve body, 15. Remove the plastic plug from the as shown, using a 1/4 x 1 inch clevis pin. hydraulic pump port. Secure the clevis pin with a cotter pin (bend the cotter pin to make it secure). 12.
-
Page 10: Start-Up Procedure
5. Push the valve control handle, with one hand, to the forward (extend) position 19. The log splitter is now completely assem- (towards the splitting wedge) and pull the engine starter cord, with the other hand, bled. Follow the “Start-Up Procedure”, in (approximately 15 times) until the cylinder piston moves forward. -
Page 11: Towing
Towing 4. Attach the towing safety chains to the tow vehicle. WARNING Maximum Speed Limit — 35 mph Your log splitter is built on a solid, unsuspended axle. To prevent damage or possible loss of vehicle control, use extreme caution when towing and do not exceed a vehicle speed of 35 mph, especially when driving on a bumpy road. -
Page 12: Operation
Operation WARNING WARNING Before loading and operating the log splitter, put on the proper protective gear such as safety goggles, Do not attempt to operate the log splitter without fully understanding face shield, hearing protection, tight-fitting gloves all our instructions, safety precautions, and/or warnings. If any doubt (without draw strings or loose cuffs), and steel-toed shoes. - Page 13 b. Only using your hand, push the control c. Hold the control lever, extending the lever forward (towards the log). If the pusher plate, until the log is split or the log moves before it is contacted by the cylinder rod stops at its maximum trav- pusher plate, release the control lever el position.
-
Page 14: Inspection And Maintenance
Inspection and Maintenance Notes General Maintenance Check (before operating) The hydraulic system (hoses, cylinder, and pump) should be carefully inspected before each use. Also, inspect the mechanical parts at the same time. Make sure all hoses, clamps, nuts, bolts, fittings, etc. are properly installed and tightened. WARNING Do not check for leaks with your hand. -
Page 15: Hydraulic Oil Change
Hydraulic Oil Change 4. Refill the hydraulic tank. a. Reconnect inlet hose (2) to the pump. Iron & Oak Commercial Products recommends an oil and filter change every 100 hours of operation. Refer to the “Specifications” section in this manual for the type and quan- b. -
Page 16: Specifications
Overall Shipping Size (H x W x L) ..... . 31.5 x 28 x 78 inches Model BHH2099 only. 2. If all engine settings are correct, replace the pump. -
Page 17: Decals
Decals WARNING Make sure all decals are attached to the log splitter and/or engine and are legible at all times. (NS) Item Part No. Description Qty. 1 (NS) BR002627 Decal, Iron & Oak, 22 Ton Decal, Iron & Oak, 30 Ton BR002652 Decal, Notice BR002621... -
Page 18: Parts
Parts Iron & Oak 815-672-8596 815-672-8596 Iron & Oak... - Page 19 Iron & Oak 815-672-8596 815-672-8596 Iron & Oak...
- Page 20 Iron & Oak 815-672-8596 815-672-8596 Iron & Oak...
-
Page 21: Warranty
Warranty For one year from the date of purchase, Iron & Oak Commercial Products Inc. will replace for the original purchaser or repair free of charge, all parts of the Iron & Oak Commercial Products Hydraulic Log Splitter, returned to our factory PREPAID and found upon inspection by us to be faulty, due to defects in materials or workmanship. -
Page 22: Optional Attachment
Optional Attachment 4-Way Wedge Assembly 4-Way Wedge Assembly Item Part No. Description Qty. BR021270 Wedge Weldment BR021271 Post Weldment BR001255 Bolt, 3/4 x 2-1/2” BR001321 Locknut, 3/4” 5 (NS) BR020264 Spacer, 2-1/2” 6 (NS) BR020265 Spacer, 3-1/2” NS - Not Shown 815-672-8596 Iron &... - Page 23 Iron & Oak Commercial Products, Inc. 410 W. Broadway Ave. Streator, Illinois 61364-0577 Phone: 815-672-8596 Fax: 815-672-9073 E-mail: sales@logsplitters-ironoak.com Web Site: www.logsplitters-ironoak.com BHH2099/BHH3099...
Need help?
Do you have a question about the BHH2099 and is the answer not in the manual?
Questions and answers