Related Manuals for Iron & Oak BHH2003
Summary of Contents for Iron & Oak BHH2003
-
Page 1: Log Splitter
I I r r o o n n & & O O a a k k 2 2 0 0 a a n n d d 3 3 0 0 T T o o n n Horizontal Log Splitter M M o o d d e e l l B B H H H H 2 2 0 0 0 0 3 3 a a n n d d B B H H H H 3 3 0 0 0 0 3 3 Owner / Operator and Safety Manual... - Page 2 Initial Start-up Instructions ❏ ❏ Read all assembly, operating, and safety instructions. ❏ ❏ Complete and return the warranty card to register your log splitter. ❏ ❏ Write the serial number and date-of-purchase in this manual. ❏ ❏ Assemble the log splitter. ❏...
-
Page 3: Table Of Contents
Contents WARNING Introduction ............4 To avoid personal injury or death, carefully read and understand all Safety. -
Page 4: Introduction
With 20 or 30 tons of splitting force, a 12 second cycle time, and a 5 or 9 the work area. HP engine, the BHH2003 or BHH3003 will handle most of your commercial log splitting needs. An attractive, powder-coated finish provides the finest protection available, and ✘... -
Page 5: Log Splitting Safety
✘ ✔ Do not, under any circumstances, alter your log splitter. This equipment was ALWAYS check the oil level in the hydraulic oil tank and engine reservoir. designed and engineered to be used in accordance with the operating instruc- tions. Altering the equipment, or using the equipment in such a way as to cir- ✘... -
Page 6: Refueling
The following chart contains the list of parts that should be shipped as part of the ✔ Always store gasoline in an approved, tightly sealed container. Store the con- BHH2003 or BHH3003 Log Splitter. tainer in a cool, dry place. Do not store the container in a house or near any Description Description heating appliance. -
Page 7: Unpacking The Crate
Unpacking the Crate Assembly Procedure 1. Cut the metal banding and remove the top, CAUTION sides, ends, and protective plastic cover- Some components are very heavy ing of the packing crate. Do not remove and can be damaged if mis-han- the base unit or the rail assembly from the dled. - Page 8 4. Position wooden blocking under the 7. Bolt the base unit to the rail assembly engine mounting plate to level and support using four 1/2-13 x 1-1/2 inch long hex the base unit. head bolts, lockwashers, and nuts, as shown. Tighten the nuts securely. 5.
- Page 9 11. Install the valve link onto the valve body, 15. Attach the other high-pressure hose from as shown, using a 1/4 x 1 inch long cle- the pump to the bottom of the valve. vis pin. Secure the clevis pin with a cot- Securely tighten the hose fitting.
-
Page 10: Start-Up Procedure
Start-up Procedure 5. Push the valve control handle, with one hand, to the forward (extend) position (towards the splitting wedge) and pull the engine starter cord, with the other hand, (approximately 15 times) until the cylinder piston moves forward. (Keep everything Important Notice away from the pusher plate and wedge during this step.) Do not start the engine. -
Page 11: Towing
Towing 4. Attach the towing safety chains to the tow vehicle. WARNING Maximum Speed Limit — 35 mph Your log splitter is built on a solid, unsuspended axle. To prevent damage or possible loss of vehicle control, use extreme caution when towing and do not exceed a vehicle speed of 35 mph, especially when driving on a bumpy road. -
Page 12: Operation
Operation WARNING WARNING Before loading and operating the log splitter, put on the proper protective gear such as Do not attempt to operate the log splitter without fully understanding safety goggles, face shield, hearing protec- all our instructions, safety precautions, and/or warnings. If any doubt tion, tight-fitting gloves (without draw strings or loose cuffs), and steel-toed or question arises about the correct or safe method of performing any- shoes. - Page 13 b. Only using your hand, push the control c. Hold the control lever, extending the lever forward (towards the log). If the splitting wedge, until the log is split or log moves before it is contacted by the the cylinder rod stops at its maximum pusher plate, release the control lever travel position.
-
Page 14: Inspection And Maintenance
Inspection and Maintenance Notes General Maintenance Check (before operating) The hydraulic system (hoses, cylinder, and pump) should be carefully inspected before each use. Also, inspect the mechanical parts at the same time. Make sure all clamps, nuts, bolts, fittings, etc. are properly installed and tightened. WARNING Do not check for leaks with your hand. -
Page 15: Hydraulic Oil Change
Hydraulic Oil Change 4. Refill the hydraulic tank. a. Reconnect inlet hose (2) to the pump. Iron & Oak Commercial Products recommends an oil and filter change every 100 hours of operation. Refer to the “Specifications” section in this manual for the type and quan- b. -
Page 16: Specifications
Gear Pump ....... . 2-stage, 11 GPM or 16 GPM Problem: The pusher plate moves slowly, but will split wood. Model BHH2003 only. 1. Check the oil level in the hydraulic tank and fill if necessary. Model BHH3003 only. -
Page 17: Decals
Decals WARNING Make sure all decals are attached to the log splitter and/or engine and are legible at all times. (8) (NS) Item Part No. Description Qty. BR002627 Decal, Iron & Oak, 22 Ton Decal, Iron & Oak, 30 Ton BR002652 Decal, Notice BR002621... -
Page 18: Parts
Parts Iron & Oak 815-672-8596 815-672-8596 Iron & Oak... - Page 19 Iron & Oak 815-672-8596 815-672-8596 Iron & Oak...
- Page 20 Iron & Oak 815-672-8596 815-672-8596 Iron & Oak...
-
Page 21: Warranty
Warranty For one year from the date of purchase, Iron & Oak Commercial Products Inc. will replace for the original purchaser, or repair free of charge, all parts of the Iron & Oak Commercial Products’ Hydraulic Log Splitter, returned to our factory PREPAID and found upon inspection by us to be faulty, due to defects in materials or workmanship. -
Page 22: Optional Attachment
Optional Attachment 4-Way Wedge Assembly 4-Way Wedge Assembly Item Part No. Description Qty. BR021270 Wedge Weldment BR021271 Post Weldment BR001255 Bolt, 3/4-13 x 2-1/2” BR001321 Locknut, 3/4-13 5 (NS) BR020264 Spacer, 2-1/2” 6 (NS) BR020265 Spacer, 3-1/2” NS - Not Shown Safety Flag Kit (Part No. - Page 23 Iron & Oak Commercial Products, Inc. 410 W. Broadway Ave. Streator, Illinois 61364-0577 Phone: 815-672-8596 Fax: 815-672-9073 E-mail: sales@logsplitters-ironoak.com Web Site: www.logsplitters-ironoak.com BHH2003-00/BHH3003-01 01/04...
Need help?
Do you have a question about the BHH2003 and is the answer not in the manual?
Questions and answers