Advertisement
INSTALLATION
The CHR-PM80 can be mounted for portable or fixed desktop usage, or it can be
fixed to a wall. The horizontal base allows portable and fixed desktop usage, while
the inclined base provides desktop and wall mounting guaranteeing a comfortable
handling of the PowerScan™ M8300 reader.
The cradle package contains the following items:
CHR-PM80
1 horizontal base
CHR-PM80 Quick Reference Guide
1 inclined base
2 adhesive strips
2 wall-mounting lock hinges
4 rubber feet
DESKTOP MOUNTING
Rubber Foot Seat (4)
Mounting Tabs (4)
Adhesive Strip Seat (2)
Mounting Holes (2)
Cable Channels
Figure 3 - Horizontal Base Front and Bottom View
Adhesive Strip Seat (2)
Cable Channels
Mounting Tabs (4)
Mounting Holes (4)
Rubber
Foot Seat (4)
Figure 4 - Inclined Base Front and Bottom View
Portable Desktop Use
1.
Correctly position the CHR-PM80 onto the base by sliding it along the
mounting tabs until aligned.
1
1
2
2
2.
Carefully clean the rubber foot seats of the base to remove any impurities
that could reduce adhesion.
3.
Remove the protective plastic from the rubber feet and stick them onto the
bottom surface of the base.
Fixed Desktop Use
For fixed desktop installation, use the adhesive strips or fixing screws (not
provided) according to your needs.
For mounting with adhesive strips:
1.
Position the cradle onto the base by sliding it along the mounting tabs until
aligned.
2.
Carefully clean the adhesive strip seats of the base to remove any impurities
that could reduce adhesion.
3.
Remove the protective plastic from one side of the adhesive strips and stick
them onto the base surface.
4.
Position the cables to be connected to the C-8000 cradle along the
dedicated channels.
5.
Remove the plastic from the other side of the strips and affix the base to the
table.
For mounting with screws:
1.
Position the cables to be connected to the C-8000 cradle along the
dedicated channels.
2.
Position the base on the table and affix it by means of the screws (not
provided).
3.
Position the cradle on the base by sliding it along the mounting tabs until
aligned.
WALL MOUNTING
1.
Remove the yellow caps and insert the two wall mounting lock hinges
provided with your cradle.
2.
Position the cables to be connected to the C-8000 cradle along the
dedicated channels.
If using the adhesive strips:
If using the mounting screws:
3.
Carefully clean the adhesive strip
3.
Using the mounting holes on the
seats of the base to remove any
base as a pattern, mark the wall
impurities
that
could
reduce
where you desire to mount the
adhesion.
CHR-PM80.
4.
Remove the protective plastic
4.
Drill the appropriate size holes and
from one side of the adhesive
insert the threaded dowels (not pro-
strips and stick them onto the
vided) into the holes.
base surface.
5.
Remove the plastic from the other
5.
Position the base on the wall as
side of the strips and affix the
indicated in the figure below and
base to the wall as indicated in
affix it by means of the screws (not
the figure below.
provided).
Inclined Base Wall-mounting
6.
Attach the cradle onto the base by sliding it along the mounting tabs until
aligned.
DATALOGIC ADC LIMITED FACTORY WARRANTY
Warranty Coverage
Datalogic warranties this product against defects in workmanship and materials, for a
period of 3 years from the date of shipment, provided that the product is operated under
normal and proper conditions.
Datalogic ADC ("Datalogic") hardware products are warranted against defects in material
and workmanship under normal and proper use. The liability of Datalogic under this war-
ranty is limited to furnishing the labor and parts necessary to remedy any defect covered
by this warranty and restore the product to its normal operating condition. Repair or
replacement of product during the warranty does not extend the original warranty term.
Products are sold on the basis of specifications applicable at the time of manufacture and
Datalogic has no obligation to modify or update products once sold.
If Datalogic determines that a product has defects in material or workmanship, Datalogic
shall, at its sole option repair or replace the product without additional charge for parts
and labor, or credit or refund the defective products duly returned to Datalogic. To per-
form repairs, Datalogic may use new or reconditioned parts, components, subassemblies
or products that have been tested as meeting applicable specifications for equivalent new
material and products. Customer will allow Datalogic to scrap all parts removed from the
repaired product. The warranty period shall extend from the date of shipment from Data-
logic for the duration published by Datalogic for the product at the time of purchase (War-
ranty period). Datalogic warrants repaired hardware devices against defects in
workmanship and materials on the repaired assembly for a 90 day period starting from the
date of shipment of the repaired product from Datalogic or until the expiration of the orig-
inal warranty period, whichever is longer. Datalogic does not guarantee, and it is not
responsible for, the maintenance of, damage to, or loss of configurations, data, and appli-
cations on the repaired units and at its sole discretion can return the units in the "factory
default" configuration or with any software or firmware update available at the time of the
repair (other than the firmware or software installed during the manufacture of the prod-
uct). Customer accepts responsibility to maintain a back up copy of its software and data.
Warranty Claims Process
In order to obtain service under the Factory Warranty, Customer must notify Datalogic of
the claimed defect before the expiration of the applicable Warranty period and obtain
from Datalogic a return authorization number (RMA) for return of the product to a desig-
nated Datalogic service center. If Datalogic determines Customer's claim is valid, Datalogic
will repair or replace product without additional charge for parts and labor. Customer shall
be responsible for packaging and shipping the product to the designated Datalogic ser-
vice center, with shipping charges prepaid. Datalogic shall pay for the return of the prod-
uct to Customer if the shipment is to a location within the country in which the Datalogic
service center is located. Customer shall be responsible for paying all shipping charges,
duties, taxes, and any other charges for products returned to any other locations. Failure
to follow the applicable RMA policy, may result in a processing fee. Customer shall be
responsible for return shipment expenses for products which Datalogic, at its sole discre-
tion, determines are not defective or eligible for warranty repair.
Warranty Exclusions
The Datalogic Factory Warranty shall not apply to:
(i)
any product which has been damaged, modified, altered, repaired or upgraded
by other than Datalogic service personnel or its authorized representatives;
(ii) any claimed defect, failure or damage which Datalogic determines was caused
by faulty operations, improper use, abuse, misuse, wear and tear, negligence,
improper storage or use of parts or accessories not approved or supplied by
Datalogic;
(iii) any claimed defect or damage caused by the use of product with any other
instrument, equipment or apparatus;
(iv) any claimed defect or damage caused by the failure to provide proper
maintenance, including but not limited to cleaning the upper window in
accordance with product manual;
(v) any defect or damage caused by natural or man-made disaster such as but not
limited to fire, water damage, floods, other natural disasters, vandalism or
abusive events that would cause internal and external component damage or
destruction of the whole unit, consumable items;
(vi) any damage or malfunctioning caused by non-restoring action as for example
firmware or software upgrades, software or hardware reconfigurations etc.;
(vii) the replacement of upper window/cartridge due to scratching, stains or other
degradation and/or
(viii) any consumable or equivalent (e.g., cables, power supply, batteries, keypads,
touch screen, triggers etc.).
No Assignment
Customer may not assign or otherwise transfer its rights or obligations under this warranty
except to a purchaser or transferee of product. No attempted assignment or transfer in vio-
lation of this provision shall be valid or binding upon Datalogic
DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, ORAL OR WRITTEN, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITA-
TION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PUR-
POSE, OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE FOR ANY DAMAGES
SUSTAINED BY CUSTOMER ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF
PRODUCTS UNDER THE ABOVE. THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT
IS THE CUSTOMER'S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY CLAIMS. UNDER NO
CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR
ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CON-
TINGENT DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE NOTICE OF
THE POSSIBILITY OF SUCH DAMAGES.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic
shall assume risk of loss or damage for product in Datalogic's possession. In the absence of
specific written instructions for the return of product to Customer, Datalogic will select the
carrier, but Datalogic shall not thereby assume any liability in connection with the return
shipment.
©2007-2013 Datalogic, Inc. • All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S.A. and the
E.U.
www.datalogic.com
DECLARATION OF CONFORMITY
Datalogic ADC Srl, Via S. Vitalino, 13
EC-104
Lippo di Calderara di Reno (BO) 40012 Italy
Rev.: 0
13
Pag.: 1 di 1
La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva di Datalogic ADC Srl per:
This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC Srl for:
Cette déclaration de conformité est établie sous la seule responsabilité de Datalogic Srl pour:
Diese Konformitätserklärung wird unter der alleinigen Verantwortung des Datalogic ADC Srl erteilt für:
Esta declaración de conformidad se expide bajo la exclusiva responsabilidad de Datalogic ADC Srl para:
CHR-PM80 ; Charger Only Base
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l' U nion Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
2004/108/EC - EMC Directive
2011/65/EU - RoHS Directive
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei
prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product
safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des
produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und
Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y
las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022 (C
B ITE ),
L
LASS
IMITS AND METHODS OF MEASUREMENTS OF RADIO
S
2006:
EPTEMBER
DISTURBANCE CHARACTERISTICS OF INFORMATION
A
A1: O
2007:
MMENDMENT
CTOBER
TECHNOLOGY EQUIPMENT
EN 55024, SEPTEMBER 1998:
I
NFORMATION TECHNOLOGY EQUIPMENT
AMENDMENT A1:2001+A2:2003:
C
L
M
HARACTERISTICS
IMITS AND
ETHODS OF
SUREMENT
EN 50581, S
2012:
T
D
A
EPTEMBER
ECHNICAL
OCUMENTATION FOR THE
SSESSMENT OF
E
E
P
LECTRICAL AND
LECTRONIC
RODUCTS WITH
R
R
H
ESPECT TO THE
ESTRICTION OF
AZARDOUS
STANCES
Lippo di Calderara, March29th , 2013
Ruggero Cacioppo
Quality & Reliability Manager - Europe
- I
MMUNITY
M
-
EA
S
-
UB
Advertisement
