Using The Cr-314 Remote Control - Arcam CD192 Handbook

Using the CR-314 remote control

Ensure that CD mode is selected using the
toggle button. The 'CD' LED above the
button is lit briefly when CD mode is selected.
Turns the display on or off. Turning the display off
generally produces a slight improvement in sound
This button enables you to repeat any section of music
within a track. Whilst the disc is playing, press the
button at the start of the section you wish to repeat.
'REPEAT' is shown on the display and the letter 'A–'
flashes. Press the button a second time when you reach
the end of the section you wish to repeat. The 'A–B'
letters stop flashing and remain lit. This section will
repeat until you press or
button ( ) moves forward within the selected loop.
To repeat the entire CD or a pre-programmed selection
of tracks press once: 'REPEAT' lights on the display.
RPT
To repeat a particular track, select that track and then
press twice so that 'REPEAT 1' is shown on the
RPT
display. If you now select a different track, that track is
To cancel the repeat function press
Search backwards and forwards;
Skip track backwards and forwards (see page 5)
Opens and closes the CD tray
Pause, Play and Stop (see page 5)
Press once to shuffle play CD tracks (i.e. play them in
a random order). Press again to cancel shuffle play.
Press once to display the remaining time of the
TITLE
currently playing track. Press again to display the time
remaining of the disc. Press a third time to turn the text
Press again and the display reverts to its original
TITLE
setting, showing the time elapsed for the current track.
For CDs with text, pressing
loaded but not playing displays the artist's name.
Pressing a second time displays the total number
TITLE
of tracks and the total playing time.
CD192
E-6
CD/DVD
CD/DVD
CD/DVD
DISP (display)
quality.
A–B
A–B
or . The forward search
RPT (repeat)
repeated instead.
a third time.
RPT
Search and Skip Track
OPEN
Playback control
P MODE
TITLE
display on.
once while the disc is
TITLE
CD/DVD REMOTE
CD DVD
CD
1 2 3
DVD
4 5 6
DISP
7 9
8
A-B
0
RPT CLEAR PROG
OK
OPEN
MUTE
P
SUBT TITLE MENU
MODE
ZOOM AUDIO MEM RTN
ANGLE SETUP STATUS SRCH
CR-314
0–9 keypad
This allows direct access to individual tracks on the disc.
To select a track, press the corresponding keypad button.
For tracks greater than 9, enter the digits in sequence.
For example, to play track 15, press and hold
number on the display moves to the left, then press
CLEAR
If you make a mistake whilst programming you can
delete the last entered track by pressing
To delete all the programmed tracks, press
repeatedly until '0' is displayed.
To exit the program facility, press
PROG (Program)
You can program a selection of up to 24 tracks from
a disc to play in any order. Select a track by using the
and buttons, then press
track into memory ('PROGRAM' appears on the display
to indicate that you have started programming a
sequence). Repeat these steps to program the remaining
tracks in your selection. Alternatively, press
and enter your track selection using the 0–9 keypad.
The display shows the track numbers programmed,
the total length of the programmed sequence and the
number of tracks programmed (shown by a number
below the word 'STEP').
Each time you enter a track the number below 'STEP'
increments by one and flashes until you press
to confirm. If you fail to press
seconds the display stops flashing and you will have to
reselect the track.
Press to play the program. Press
entire sequence from the start. Press and hold
erase the programmed sequence. Press
exit the program facility.
MUTE
Stops sound to the speaker outputs of certain Arcam
amplifiers.
Volume +/–
Adjusts the volume on Arcam remote-controllable
amplifiers.
Note that the volume (+/–) controls and
have no effect on the audio output level of the CD
players.
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control.
Do not place anything in front of the display area
on the CD player (where the IR receiver is located),
or the remote control may not work.
Note that greyed-out buttons on the remote control
are DVD-specific and are not used with the CD
player.
until the
1
.
5
.
CLEAR
CLEAR
.
PROG
to program the
PROG
once
PROG
PROG
within about five
PROG
again to replay the
to
CLEAR
again to
PROG
button
MUTE