Using The Remote Control; Cr-314 Remote Control; Search - Arcam CD92 Handbook

Using the remote control

CR-314 Remote Control

Note that greyed-out buttons on the remote control are DVD-
specifi c and are not used with the CD player.
Ensure that CD mode is selected using the
toggle button. The 'CD' LED above the
button is lit briefl y when CD mode is selected.
Turns the display on or off. Turning the display off generally
produces a slight improvement in sound quality.
This button enables you to repeat any section of music within
a track. Whilst the disc is playing, press the
start of the section you wish to repeat. 'REPEAT' is shown on
the display and the letter 'A–' fl ashes. Press the button a second
time when you reach the end of the section you wish to repeat.
The 'A–B' letters stop fl ashing and remain lit. This section will
repeat until you press or or . The forward search button
( ) moves forward within the selected loop.
To repeat the entire CD or a pre-programmed selection of tracks
press once: 'REPEAT' lights on the display. To repeat a
RPT
particular track, select that track and then press
that 'REPEAT 1' is shown on the display.
different track, that track is repeated instead.
To cancel the repeat function press
Search and Skip Track
Search backwards and forwards;
Skip track backwards and forwards (see page 5)
Opens and closes the CD tray
Pause, Play and Stop (see page 5)
Press once to shuffl e play CD tracks (i.e. play them in
a random order). Press again to cancel shuffl e play.
Press once to display the remaining time of the currently
TITLE
playing track. Press again to display the time remaining of
the disc. Press a third time to turn the text display on.
Press TITLE again and the display reverts to its original setting,
showing the time elapsed for the current track.
For CDs with text, pressing TITLE
is loaded but not playing displays the artist's name.
Pressing TITLE a second time displays the total number of
tracks and the total playing time.
CD72/92
6
CD/DVD
CD/DVD
CD/DVD
DISP (display)
CD/DVD REMOTE
CD DVD
A–B
CD
1
DVD
A–B button at the
4
DISP
7
A-B
RPT CLEAR
RPT (repeat)
RPT twice so
If you now select a
OPEN
a third time.
RPT
OPEN
Playback control
P MODE
P
SUBT
MODE
ZOOM AUDIO
TITLE
ANGLE SETUP
once while the disc
CR-314
0–9 keypad
This allows direct access to individual tracks on the disc. To
select a track, press the corresponding keypad button and then
press . For tracks greater than 9, enter the digits in sequence.
For example, to play track 15, press and hold
on the display moves to the left, then press
CLEAR
If you make a mistake whilst programming you can delete
the last entered track by pressing
the programmed tracks, press
2 3
displayed.
To exit the program facility, press
5 6
9
8
PROG (Program)
0
PROG
You can program a selection of up to 24 tracks from a
disc to play in any order. Select a track by using the
and buttons, then press
memory ('PROGRAM' appears on the display to indicate that you
have started programming a sequence). Repeat these steps to
program the remaining tracks in your selection. Alternatively,
press PROG once and enter your track selection using the 0–9
OK keypad.
The display shows the track numbers programmed, the total
length of the programmed sequence and the number of tracks
programmed (shown by a number below the word 'STEP').
Each time you enter a track the number below 'STEP' increments
by one and fl ashes until you press
press within about fi ve seconds the display stops fl ashing
PROG
and you will have to reselect the track.
MUTE
Press to play the program. Press
sequence from the start. Press and hold
programmed sequence. Press
facility: the display fl ashes 'CONTINUE' and shows '0'.
MUTE
Stops sound to the speaker outputs of certain Arcam amplifi ers.
TITLE MENU
Volume +/–
Adjusts the volume on Arcam remote-controllable amplifi ers.
MEM RTN
Note that the volume (+/–) controls and
no effect on the audio output level of the CD players.
STATUS SRCH
NOTE: Remember to install the two AAA batteries supplied
before trying to use your remote control.
Do not place anything in front of the display area on the
CD player (where the IR receiver is located), or the remote
control may not work.
until the number
1
.
5
. To delete all
CLEAR
repeatedly until '0' is
CLEAR
.
PROG
to program the track into
PROG
PROG to confi rm. If you fail to
again to replay the entire
to erase the
CLEAR
PROG again to exit the program
button have
MUTE