Optex Prowave Air-wave RX Installation Instructions

Prowave Air-wave RX
SINGLE RELAY RECEIVER (RG-10U)
Air-wave RX INSTALLATION INSTRUCTIONS
Please read this manual carefully before installation.
1 CAUTION AND WARNING
WARNING
1. Harsh environments
Using the Air-wave outdoors in severe conditions such as extreme temperatures,
rapid temperature change, high humidity, steam or fog may cause malfunction.
2. Tampering
Any changes or modifications not expressly approved by OPTEX could void
the user's authority to operate the equipment
(see FCC note in section 13 COMPLIANCE of this manual).
2 PARTS IDENTIFICATION
Zone indicator 1
Zone indicator 2
Zone indicator 3
Switch 1
Power
indicator
Power
Switch
Switch 2
FRONT
Note: When you recycle this product, please disassemble product and recycle according to state law.
4 INSTALLATION
How to connect the Terminal
Remove the connection terminal cover
5 TEACH TRANSMITTER CODES TO Air-wave RX "LEARN MODE"
Each transmitter has a unique transmission code, which
can be automatically "learned" by the Air-wave RX. The
Air-wave RX's zones must be taught to respond to the
appropriate transmitter. The zone characteristics can be
programmed as shown below.
Activate "LEARN" Mode
A) The Air-wave RX
automatically starts in
"Learn" mode if no
transmitter code has been
programmed.
B) Press and hold Switch 1
until the power indicator
starts to flash.
Note:
•
Revert to normal operation status before use.
•
Verify that each transmitter has been learned by the receiver by triggering them.
•
Each zone can accept a maximum of 3 transmitters, and the zone indicator shows the activated
transmitter based on the number of flashes.
(e.g. If transmitter 2 in zone 1 is activated, the zone 1 indicator flashes twice)
•
A single transmitter cannot be learned by multiple zones.
•
Turning off the devices, or losing power will not affect the transmitter or the Air-wave RX 's code memory.
Mounting
hole
Connection
terminal
cover
Output
connection
terminal
BACK
Remove knockouts according to wiring needs.
Teach the transmitter code to the receiver
Zone 1
OR
Receiver starts
in Zone 1.
FEATURES
Identifies zone (location) by 3 LED lights (3 zones + 1 continuous zone).
Able to learn 12 transmission codes (Each zone can learn 3 transmitters maximum).
Automatic "Learning" function facilitates to preset transmission codes to Air-wave RX.
Over 8 million codes possible, eliminates interference from neighbors.
Latches into alarm with "Continuous mode" function.
Adjustable duration for terminal output.
Low battery indicator to recognize transmission units' battery status.
CAUTION
1. Impact/Shock
Impact or Shock can cause severe damage or break the Air-wave RX.
2. Electric Devices
Use Air-wave RX at least 3ft (1m) away from electronic devices such as TVs, Radios, PCs,
Microwave ovens. This may cause the unit to malfunction.
3. Transmission range
Transmission range may decrease under the following conditions:
- Either transmission units or Air-wave RX installed on a metal surface.
- Presence of a steel door, reinforced concrete or other metal obstructions between
transmission units and Air-wave RX.
- Places near strong radio sources such as broadcast stations or substation.
4. Cleaning
Harsh cleaners such as paint removers or benzene may ruin the surface. Use a soft wet
cloth and mild soap to clean.
Function
Switch 1 Activating "Learn Mode" and
"Output Duration Mode"
Switch 2 Making selection
Stand
Mounting screw
Wiring
Use a power source
within the following range; 12~24V AC/DC
When using for door controller,
connect NO and COM to activate input.
Usually the activate input is NO.
Activate the transmitter you wish to teach the receiver.
The corresponding zone indicator flashes N times rapidly at intervals of 1 sec
according to the N number of transmitters, N=Maximum 3.
Zone 2
Press Switch 2 to advance to the next zone.
Erasing Codes from the Air-wave RX's Memory
1) Hold down switch 1 until the power indicator starts to flash.
2) Press Switch 2 until the appropriate zone indicator is lit.
3) Press Switch 1 to erase. The zone indicator will start to flash.
(Note: All programming in that particular zone will be erased.)
4) Press Switch 2 a few times until the power indicator stops flashing and remains lit.
Note: To erase all programming and revert to the factory default setting, turn on the
power while pressing and holding Switch 1.
3 TRANSMISSION RANGE (REFERENCE)
Transmission range must be changed according to environment.
Please check if system works properly for the site.
1000ft (Open field, line of sight)
Sensor unit
150ft (Stucco/Plaster construction)
Air-wave TX
100ft (Concrete construction)
700ft (Open field, line of sight)
Button unit
110ft (Stucco/Plaster construction)
TS-10U
70ft (Concrete construction)
Zone 1: Timed utility output
Zone 2: Timed utility output
Zone 3: Timed utility output
Zone 4: Continuous terminal output
(latches until Switch 2 is pressed to deactivate)
Zone 3 Zone 4
Press Switch 2 to revert to
normal operation status.
Receiver
Air-wave RX
Normal
Operation Status