Optex Wireless 2000 RC-20U Installation Instructions

@orenex
2000
Annunciator
$lstem
CHIME BOX
WRELAY
RECEIVER
RC.2OU INSTALLI\TION INSTRUCTIONS
Pleago rcad this manual oarefully before installation.
FEATURES
.
Compatible
with
TD.20U
(lndoor/Outdoor
Sensor Transmittefl,TS-10U (Hand.Held Transmitter),
TR-20U(Repeate|, TC.'l0U(DoorMindow Transmitter) and any transmission units
of WlRELESS1000 series.
.
ldentifies
4
zones
by
3
different
tones and LED
lights
(3
normal zones +
1
continuous
zone).
.
Able to learn
l2
transmission codes (Each zone can learn
3
transmitters maximum).
.
Automatic "Learning" function facilitates to preset
transmission codes to RC.20U.
.
Over 8
million codes possible, eliminates interference from neighbors.
.
Latches into
alarm
with "Continuous mode" function.
'
Programmed
"Utility Output
Mode"
to inactivate
chime
tone (applicable for zone
3).
.
Adjustable duration for terminal output.
.
Adjustable volume.
.
Low battery indicator to
recognize
transmission units'
battery status.
'
Polvered by
a
gVDC
adapto(lncluded).
WARNING
1. Harsh environments
Do not use the RC-20U outdoors, severe condilions as out of warranted
temperature, rapid temperature change, high humidity, or steam,
This may cause the unit to malfunction.
2. Tampering
Any changes or modifications not expressly approved by 0PTEX could void the user's
authorlty to operate the equipment,
3.
Adaptor
Do not use any other AC adaptor except what is included.
CAUTION
1.
lmpacUShock
lmpact or Shock can cause severe damage or break the RC-20U.
2,
Electric Devices
Use RC-20U at least 3ft
(1
m) away from electronic devices such as TVs, Radios,
PCs,
Microwave ovens, or any other devices with an electric motors.
This may cause the unit to malfunction.
3.
Transmission range
Transmission range may decrease under the following conditions:
- Either transmission units or RC-20U installed on a metal surface.
-
Presence of a steel door, reinforced concrete or other metal obstructions between
transmission units and RC-201.
- Places near strong radio sources such as broadcast stations or substation.
4.
Cleaning
Harsh cleaners such as paint removers or benzene may ruin the surface. Use a soft wet
cloth and mild soap to clean,
Zons indicator
1
Function
s*itch
1
i
+TlilliilLl'dHyro3,'*x?d0-
^
..
.
J,qcrivatirc"voLuvenolusfMEur
lwllcn
zL
MODE ind
makrnoselection.
AC
Adaptor
\-
Y@
Mounting screw
Transmission range must be changed according to environment.
Please check if system works properly for the site.
In
the case of insufficient transmission range, use
TR-20U (Repeater unit)
to extend range.
Zone indicator2
Zone
indicator 3
Switch
1
Switch
Switch
2
Adaplor
JACK
Sensorund
ffi
TD-20U
2000ft
{Open field, line of sighl)
Conn€ction
termlnal
i
Repeater l*{l
TR-20u
lin:t
Contact
unii [-=n
rclou
tl
Buttonunt
@
TS.1ou
,'ll
150ft
(Siucco/Plaster conitruction)
100f1
(Conffeto construclion)
:
1400ft
(Ops
ield,
line of sight)
150ft
(Stucco/Plaster conslruclion)
100ft
(Concreto consiruciion)
lemlnal
0utpul
conn€ction
FRONT
(lnside oflhe
cove0
BACK
Note: When you recycle this product, please disassemble product and recycle according to state
law.
Wall Mounting
Use the mounting screw
on
a
wall. Leave some
length of the screw out
for mounting hole of the
RC-20U.
Terminal connection
Any device with a zero
voltage input terminal can
be connected to this
terminal- This may include
electronic locks,
emergency s0undrng
devices, and automatic
reporting equipment.
Desktop
Pull out the stand on
the
back of the RC-20U
and
place
it
on any flat surface.
Use only the power adaptor supplied with the
product.
Remove the connection
terminal cover.
Use the terminal marked
"COM-N.0,"for
N.O.
devices and "COM-N.C,"
for
N.C. devices.
Remove knockouts
according to wiring
needs.
Close the connection
terminal
cover
I
-\l
tl
I
.r| s
,.
|-\
to
e
--l
\:
/'NZ'
\p
Each transmitter has a unique
transmitter
code
which
can be
automatically learned
by RC-20U.
The RC-20U's zones must be taught to respond to the appropriate transmitter. (No
trinsmitter
is
taught
on
default
setting.)
Note:
.
Verify that each transmitter has been successfully learned by RC-20U
by triggering them.
.
Each zone can learn max,
3
transmitters.
.
Zone indicator shows the activated transmitter
bV
the number of flash.
Erasing codes
from
RC-20U's
memory.
1) Hold down switch
1
until the oower indicator starts to flash.
2) Press switch 2 until the appropriate zone indicator
is
lit.
3) Press switch
1
to erase. The zone
indrcatorwill startto
flash
-{;arinr
Teach the transmitter code to
RC-20U
Activaie the transmitter you wish to teach the receiver.
(
H:::::fi:: li,'J""::i,::::*:li:'""''|e'a'
s
o'f
)
starts in
"LEARN
|\4ODE"
rf no
transmitter code has
been programmed.
OR
B) Press and hold switch
'1
11 \\
until the power indicator
U \\ et.de
t^
flrch
-lFeee
I
'l
il
Press switch
2
to return
to
normal operation status.