Optex RX-460 Installation Manual

Installation Manual

Wireless Push Button & Receiver
TX-460/RX-460

General information

IMPORTANT!
In order to get the best out of your system it is important you take
the time to read through the instruction before you start to install/
program your equipment.
Frequency modulation
The system works at the frequency 433.92 MHz and uses frequency
modulation.
Self-learning of code
Each TX-460 transmitter supplied has a fixed, individual code that
cannot be altered. In system TX/RX-460, transmitters and receivers
are co-coded through self-learning, i.e. the receiver learns the trans-
mitter's code.
Preparations
Assembly and installation
1. Select a suitable location for assembly of the receiver.
2. Connect the operating voltage to the receiver (12-30V AC/DC).
3. Co-program transmitter and receiver by pushing two times on the
programming button of the RX-460 and then once on the TX-460.
4. Mount the transmitter on a flat surface. Make sure the batteries
are fitted correctly in the transmitter.
5. Connect the required functions to be controlled over the receiver.
TX-460 transmitter
The TX-460 can control the RX-460 receiver over a large distance,
even within buildings. Upon activating the push button by pushing it,
a signal is transmitted. No matter how short or fast the push on the
push button is, the full signal will be transmitted, and the receiver will
always be activated.
The TX-460 has a fixed, private code that cannot be altered. This is
meant to give the push button its own coding within the 433.92 MHz
band, so no other system can take over the control. All push buttons
have a unique code.
Installation
To mount the push button on a surface, make sure that the surface is
as equally flat as possible. A surface which is not equally flat will not
provide a good mounting position for the push button, and will inter-
fere with normal functioning of the push button.
Since surfaces where the TX-460 is to be mounted upon differ, no
standard screws or other mounting material is provided. When you
have chosen screws to install the TX-460, make sure that the head
of the screw is not bigger than 8 mm, otherwise the TX-460 will be
damaged and disfunction.
TX-460 transmitter
2x
Battery replacement
4 batteries AAA 1,5V
1x
RX-460 receiver
The RX-460 is a self-learning plug-in receiver which can learn up to 50
differtent signals. It consists of 1 relay output which can be used as a
Normally Open (NO) or Normally Closed (NC) contact.
The power supply on the receiver should be 12 to 30 Volts AC or DC.
The supply can be between these values, and it does not matter how
the voltage is connected.
1. Programming button Button for programming and/or erasing
2. Green LED LED lights when the receiver receives
a radio signal
3. Yellow LED LED lights when the receiver has the
correct operating voltage
4. Red LED LED shows programming status
5. Relay Max. load over relay is 8A for resistive load
6. Connection terminal Connection terminal for voltage
7. Connection terminal Connection terminal for relay
8. Antenna Special wire antenna for optimum reception
Learning the transmitter with the receiver
The RX-460 can learn up to 50 different signals, both group codes
(through dipswitches) as unique/private codes. The TX-460 only has
the ability to learn unique/private codes. Up to 50 TX-460 push but-
tons can be programmed on 1 RX-460 receiver. When a combination
with hand transmitters is used on a RX-460, the RX-460 has also the
ability to learn in a dipswitch setting (the group coding) of these trans-
mitters.
Push the button two times during the programming procedure to learn
the private coding and push only one time to learn the group coding.
For more information about these settings and possibilities of the
hand transmitters, we recommend you to read the installation manual
of these transmitters.
(continued)
+ +
+ +
+ +
+ +
1
2
3
4
5
6
7
8